Search Results

Standard

Rubber Boots for Drum-Type Hydraulic Brake Wheel Cylinders

2015-12-17

CURRENT

J1604_201512

This SAE Standard covers molded rubber boots used as end closures on drum-type wheel brake actuating cylinders to prevent the entrance of dirt and moisture, which could cause corrosion and otherwise impair wheel brake operation. The document includes performance tests of brake cylinder boots of both plain and insert types under specified conditions and does not include requirements relating to chemical composition, tensile strength, or elongation of the rubber compound. Further, it does not cover the strength of the adhesion of rubber to the insert material where an insert is used. The rubber material used in these boots is classified as suitable for operation in a temperature range of −40 to +120 °C ± 2 °C (−40 to + 248 °F ± 3.6 °F).

Standard

Rubber Seals for Hydraulic Disc Brake Cylinders

2014-12-03

CURRENT

J1603_201412

This SAE Standard describes the performance and part requirements for elastomeric seals used in highway vehicle disc brake calipers. Seals covered by this specification may be the solid section type (square, rectangular, O-ring, etc.) mounted stationary in the cylinder bore or on the movable piston.

Standard

Structural Testing of Passenger Car and Truck Disc Brakes

2014-11-15

CURRENT

J1713_201411

This SAE Recommended Practices specifies a procedure for determining structural strength and fatigue life of disc-brake caliper assemblies which are satisfactory for vehicle usage. It is applicable to new caliper assemblies which are employed in passenger car and truck brake systems utilizing hydraulic brake fluids. Brake design and vehicle performance requirements are not included. Specification limits are left to the discretion of the responsible manufacturer. This procedure was developed for base brake operation and does not consider some unusual effects of ABS (Anti-Lock-Brake System) or Traction Control systems which may have a significant effect on the caliper. Careful analysis of the particular type ABS and/or Traction Control should be made and additional tests may be required which are not included in this document.

Standard

Structural Testing of Passenger Car and Truck Disc Brakes

2013-02-13

HISTORICAL

J1713_201302

This SAE Recommended Practices specifies a procedure for determining structural strength and fatigue life of disc-brake caliper assemblies which are satisfactory for vehicle usage. It is applicable to new caliper assemblies which are employed in passenger car and truck brake systems utilizing hydraulic brake fluids. Brake design and vehicle performance requirements are not included. Specification limits are left to the discretion of the responsible manufacturer. This procedure was developed for base brake operation and does not consider some unusual effects of ABS (Anti-Lock-Brake System) or Traction Control systems which may have a significant effect on the caliper. Careful analysis of the particular type ABS and/or Traction Control should be made and additional tests may be required which are not included in this document.

Standard

Hydraulic Valves for Motor Vehicle Brake Systems - Performance Requirements

2012-12-03

CURRENT

J1137_201212

This SAE Recommended Practice applies to valve assemblies that are used on passenger car and light truck braking systems utilizing motor vehicle hydraulic brake fluids. The procedure (SAE J1118) and these requirements (SAE J1137) were developed for brake fluids conforming to SAE J1703 and FMVSS 116 (DOT 3) requirements; however, it may be utilized for valves which use DOT 4 or DOT 5 brake fluid. These requirements are applicable to differential warning, metering hold off, bypass function, or proportioning type valves or any combination thereof.

Standard

Rubber Dust Boots for the Hydraulic Disk Brake Piston

2012-04-30

CURRENT

J1570_201204

This SAE Standard covers molded rubber boots used on disc brake pistons to prevent the entrance of dirt and moisture which could cause corrosion and otherwise impair caliper operation. The specification includes performance tests of brake piston boots of both plain and insert types under specified conditions and does not include requirements relating to chemical composition or physical properties of the rubber compound. Further, it does not cover the strength of the adhesion of rubber to the insert material where an insert is used. The rubber material used in these boots is classified as suitable for operating in a temperature range of -40 to + 120 °C ± 2 °C (-40 to + 248 °F ± 3.6 °F).

Standard

Automotive Hydraulic Brake Tube Joints

2011-07-19

CURRENT

J2879_201107

This document applies to 90 degree double inverted flares used on common sizes of automotive hydraulic brake tubes, and their associated tube nuts and mating ports. The intent of this standard is to replace the use of SAE J512 and SAE J533 for automotive hydraulic brake tube connections.

Standard

Rubber Seals for Hydraulic Disc Brake Cylinders

2008-05-13

HISTORICAL

J1603_200805

This SAE Standard describes the performance and part requirements for elastomeric seals used in highway vehicle disc brake calipers. Seals covered by this specification may be the solid section type (square, rectangular, O-ring, etc.) mounted stationary in the cylinder bore or on the movable piston.

Standard

Hydraulic Wheel Cylinders for Automotive Drum Brakes

2006-08-16

HISTORICAL

J101_200608

This document specifies minimum performance and durability requirements for satisfactory vehicle usage, and it is applicable to wheel cylinder assemblies from commercial production, after production shipment, shelf storage, and remanufacture (factory rebuild).

Standard

Structural Testing of Passenger Car and Truck Disc Brakes

2004-06-07

HISTORICAL

J1713_200406

This SAE Recommended Practices specifies a procedure for determining structural strength and fatigue life of disc-brake caliper assemblies which are satisfactory for vehicle usage. It is applicable to new caliper assemblies which are employed in passenger car and truck brake systems utilizing hydraulic brake fluids. Brake design and vehicle performance requirements are not included. Specification limits are left to the discretion of the responsible manufacturer. This procedure was developed for base brake operation and does not consider some unusual effects of ABS (Anti-Lock-Brake System) or Traction Control systems which may have a significant effect on the caliper. Careful analysis of the particular type ABS and/or Traction Control should be made and additional tests may be required which are not included in this document.

Standard

Hydraulic Valves for Motor Vehicle Brake Systems—Performance Requirements

2002-08-07

HISTORICAL

J1137_200208

This SAE Recommended Practice applies to valve assemblies that are used on passenger car and light truck braking systems utilizing motor vehicle hydraulic brake fluids. The procedure (SAE J1118) and these requirements (SAE J1137) were developed for brake fluids conforming to SAE J1703 and FMVSS 116 (DOT 3) requirements; however, it may be utilized for valves which use DOT 4 or DOT 5 brake fluid. These requirements are applicable to differential warning, metering hold off, bypass function, or proportioning type valves or any combination thereof.

Standard

Structural Testing of Passenger Car and Truck Disc Brakes

1998-01-01

HISTORICAL

J1713_199801

This SAE Recommended Practices specifies a procedure for determining structural strength and fatigue life of disc-brake caliper assemblies which are satisfactory for vehicle usage. It is applicable to new caliper assemblies which are employed in passenger car and truck brake systems utilizing hydraulic brake fluids. Brake design and vehicle performance requirements are not included. Specification limits are left to the discretion of the responsible manufacturer. This procedure was developed for base brake operation and does not consider some unusual effects of ABS (Anti-Lock-Brake System) or Traction Control systems which may have a significant effect on the caliper. Careful analysis of the particular type ABS and/or Traction Control should be made and additional tests may be required which are not included in this document.

Standard

HYDRAULIC VALVES FOR MOTOR VEHICLE BRAKE SYSTEMS—PERFORMANCE REQUIREMENTS

1995-06-01

HISTORICAL

J1137_199506

This SAE Recommended Practice applies to valve assemblies that are used on passenger car and light truck braking systems utilizing motor vehicle hydraulic brake fluids. The procedure (SAE J1118) and these requirements (SAE J1137) were developed for brake fluids conforming to SAE J1703 and FMVSS 116 (DOT 3) requirements; however, it may be utilized for valves which use DOT 4 or DOT 5 brake fluid. These requirements are applicable to differential warning, metering hold off, bypass function, or proportioning type valves or any combination thereof.

Standard

RUBBER BOOTS FOR DRUM-TYPE HYDRAULIC BRAKE WHEEL CYLINDERS

1995-01-01

HISTORICAL

J1604_199501

This SAE Standard covers molded rubber boots used as end closures on drum-type wheel brake actuating cylinders to prevent the entrance of dirt and moisture, which could cause corrosion and otherwise impair wheel brake operation. The document includes performance tests of brake cylinder boots of both plain and insert types under specified conditions and does not include requirements relating to chemical composition, tensile strength, or elongation of the rubber compound. Further, it does not cover the strength of the adhesion of rubber to the insert material where an insert is used. The rubber material used in these boots is classified as suitable for operation in a temperature range of -40 to +120 °C ± 2 °C (-40 to + 248 °F ± 3.6 °F).

Standard

RUBBER SEALS FOR HYDRAULIC DISC BRAKE CYLINDERS

1990-06-01

HISTORICAL

J1603_199006

This SAE Standard describes the performance and part requirements for elastomeric seals used in highway vehicle disc brake calipers. Seals covered by this specification may be the solid section type (square, rectangular, O-ring, etc.) mounted stationary in the cylinder bore or on the movable piston.

Standard

HYDRAULIC WHEEL CYLINDERS FOR AUTOMOTIVE DRUM BRAKES

1989-12-01

HISTORICAL

J101_198912

This document specifies minimum performance and durability requirements for satisfactory vehicle usage, and it is applicable to wheel cylinder assemblies from commercial production, after production shipment, shelf storage, and remanufacture (factory rebuild).

Standard

RUBBER BOOTS FOR DRUM-TYPE HYDRAULIC BRAKE WHEEL CYLINDERS

1989-10-01

HISTORICAL

J1604_198910

This document covers molded rubber boots used as end closures on drum-type wheel brake actuating cylinders to prevent the entrance of dirt and moisture, which could cause corrosion and otherwise impair wheel brake operation. The document includes performance tests of brake cylinder boots of both plain and insert types under specified conditions and does not include requirements relating to chemical composition, tensile strength, or elongation of the rubber compound. Further, it does not cover the strength of the adhesion of rubber to the insert material where an insert is used. The rubber material used in these boots is classified as suitable for operation in a temperature range of -40 to + 120 ± 2°C (-40 to +248 ± 3.6°F).

Standard

AUTOMOTIVE HYDRAULIC BRAKE SYSTEM—METRIC BANJO BOLT CONNECTIONS

1989-05-01

HISTORICAL

J1291_198905

This standard documents dimensional metric specifications for hydraulic brake system threaded ports and banjo bolts for the interconnection of major components in automotive hydraulic brake systems. Banjo blocks are not covered by this standard. The purpose of this document is to recommend preferred metrically dimensioned components (including alternative choices). Some applications may require sizes or forms other than those shown herein, and this document does not preclude such other details when they are required.

Standard

AUTOMOTIVE HYDRAULIC BRAKE SYSTEM - METRIC TUBE CONNECTIONS

1989-05-01

HISTORICAL

J1290_198905

This standard documents dimensional metric specifications for hydraulic brake system tubing with flared ends, threaded ports, and male tube nuts for the interconnection of major components in automotive hydraulic brake systems. The purpose of this document is to recommend preferred metrically dimensioned components (including alternative choices), that are intended to be functionally compatible with International Organization for Standardization Specification, ISO 4038-1977 (E). Some applications may require sizes of forms other than those shown herein, and this document does not preclude such other details when they are required.

Standard

HYDRAULIC VALVES FOR MOTOR VEHICLE BRAKE SYSTEMS TEST PROCEDURE

1977-05-01

HISTORICAL

J1118_197705

The Recommended Practice specifies the test procedure to assure valve assemblies which are satisfactory for vehicle usage, and it is applicable to new valve assemblies from commercial production, and remanfacture (factory rebuild). The minimum performance and durability requirements are specified in SAE J1137, Hydraulic Valves for Motor Vehicle Brake Systems-Performance Requirements.