Search Results

Momentum conservation is a principle rule that affects the behaviour of vapour jet and liquid spray penetration. The air entrainment and mixture formation processes are dominated by the momentum transferred from the fuel to the ambient gas. Thus, it is a significant factor in the development of spray and jet penetration. This mixture formation process is well described for small-scale passenger car injectors; however, it has to be investigated in more detail for large-scale injector nozzles. The current work provides qualitative and quantitative results of spray and jet parameters in a constant volume combustion chamber (CVC). Two optical methods have been utilized to evaluate spray and jet details: Schlieren photography as a method to visualize the jet penetration and cone angle as well as Mie scattering for the phase change evaluation and the determination of liquid spray parameters.

Homogeneous lean or diluted combustion can significantly increase the efficiency of spark ignition engines. Active fuelled pre-chamber ignition systems can overcome the problem that common spark ignitions systems are incapable to ignite strongly diluted mixtures. A small portion of the charge is burned in a separated chamber, which is connected to the main chamber by multiple small orifices. The combustion inside the pre-chamber generates hot gases, which penetrate into the main chamber and ignite the diluted charge on multiple sites. Active pre-chamber ignition systems feature a separate fuelling or scavenging system in addition to the one of the main combustion chambers. Preferably, gaseous fuel is used for the pre-chamber fuelling allowing better dosing accuracy and mixture preparation inside the pre-chamber.

To address stricter emission limits, GDI develops to increased fuel pressure. Current gasoline injectors are already operating at a pressure of up to 35 MPa and an elevation is still promising lower particle emissions and increased efficiency. There have been only few studies of GDI sprays at pressures >50 MPa published. Contrary, in diesel engines injection pressure up to 250 MPa are common. GDI and diesel injector designs limit liquid penetration in different ways to avoid wall wetting, which has a negative impact on emissions in GDI combustion concepts. With elevated fuel pressure the question arises which design concept limits the penetration depth more effectively. To investigate the properties of high pressure sprays, a GDI injector (100 MPa max. fuel pressure) and an injector with diesel-like design are compared. High speed Shadowgraphy and Schlieren technique are used to gather information of liquid and vapor phase propagation.

The introduction of the so called Emission Controlled Areas within the IMO Tier III legislation forces manufacturers of maritime propulsion systems to adherence to stringent emission thresholds. Dual fuel combustion, which is characterized by the injection of a small amount of fuel oil to ignite a premixed natural gas air mixture, constitutes an option to meet this target. At high diesel substitution rates and very short pilot injection events, the injector is operated in the ballistic regime. This influences spray penetration, mixture formation and ignition behavior. In the present work, a seven-hole dual fuel injector was measured in a combustion chamber to provide data for the generation of a CFD model using the commercial code AVL FIRE®. The liquid and the vapor phase of the fuel spray were quantified by Mie-scattering and Schlieren-imaging technique for different chamber conditions.

In DISI engines spray distribution and atomization directly influence mixture formation, the quality of combustion and the resulting emissions. Constant Volume Chambers (CVC) are commonly used to characterize sprays of gasoline injectors. The CVCs provide good optical access but the flow condition of the engine cannot be reproduced. Optically accessible engines in contrast deliver realistic flow conditions but have restricted optical access. In former investigations we compared the spray propagation of different injectors in constant volume chambers and in optical accessible engines. These results showed a clear difference of the spray propagation in the CVC and the engine, especially at high charge motion conditions in the engine. To find an appropriate way to investigate the impact of different charge motion a flow channel was built with adjustable crossflow velocities from 5-50 m/s. The spray propagation during the injection process was measured with high-speed shadowgraphy.

The present study helps to understand the local combustion characteristics of PREmixed Mixture Ignition in the End-gas Region (PREMIER) combustion mode while using increasing amount of natural gas as a diesel substitute in conventional CI engine. In order to reduce NOx emission and diesel fuel consumption micro-pilot diesel injection in premixed natural gas-air mixture is a promising technique. New strategy has been employed to simulate dual fuel combustion which uses well established combustion models. Main focus of the simulation is at detection of an end gas ignition, and creating an unified modeling approach for dual fuel combustion. In this study G-equation flame propagation model is used with detailed chemistry in order to detect end-gas ignition in overall low temperature combustion. This combustion simulation model is validated using comparison with experimental data for dual fuel engine.

The fuel spray behavior in the near nozzle region of a gasoline injector is challenging to predict due to existing pressure gradients and turbulences of the internal flow and in-nozzle cavitation. Therefore, statistical parameters for spray characterization through experiments must be considered. The characterization of spray velocity fields in the near-nozzle region is of particular importance as the velocity information is crucial in understanding the hydrodynamic processes which take place further downstream during fuel atomization and mixture formation. This knowledge is needed in order to optimize injector nozzles for future requirements. In this study, the results of three experimental approaches for determination of spray velocity in the near-nozzle region are presented. Two different injector nozzle types were measured through high-speed shadowgraph imaging, Laser Doppler Anemometry (LDA) and X-ray imaging.

Three jet fuel surrogates were compared against their target fuels in a compression ignited optical engine under a range of start-of-injection temperatures and densities. The jet fuel surrogates are representative of petroleum-based Jet-A POSF-4658, natural gas-derived S-8 POSF-4734 and coal-derived Sasol IPK POSF-5642, and were prepared from a palette of n-dodecane, n-decane, decalin, toluene, iso-octane and iso-cetane. Optical chemiluminescence and liquid penetration length measurements as well as cylinder pressure-based combustion analyses were applied to examine fuel behavior during the injection and combustion process. HCHO* emissions obtained from broadband UV imaging were used as a marker for low temperature reactivity, while 309 nm narrow band filtered imaging was applied to identify the occurrence of OH*, autoignition and high temperature reactivity.

A previous study by the authors has shown an efficiency benefit of up to Δηi = 10 % for stratified operation of a high pressure natural gas direct injection (DI) spark ignition (SI) engine compared to the homogeneous stoichiometric operation with port fuel injection (PFI). While best efficiencies appeared at extremely lean operation at λ = 3.2, minimum HC emissions were found at λ = 2. The increasing HC emissions and narrow ignition time frames in the extremely lean stratified operation have given the need for a detailed analysis. To further investigate the mixture formation and flame propagation und these conditions, an optically accessible single-cylinder engine was used. The mixture formation and the flame luminosity have been investigated in two perpendicular planes inside the combustion chamber.

Pre-chamber ignition systems enable the combustion of homogeneous lean mixtures in internal combustion engines with significantly increased thermal efficiency. Such ignition systems provide a much higher ignition energy compared to a common spark ignition by burning a small portion of the charge in a separate chamber, generating multiple ignition sites in the main combustion chamber and increasing the turbulent flame speed. Pre-chamber ignition systems are commonly used in large natural gas engines but the integration in automotive engines is not feasible so far due to the lack of suitable fuelling systems needed to keep the pre-chamber mixture stoichiometric at lean operation of the engine. Based on preliminary investigations we developed an ignition system with fuelled pre-chamber for automotive engines utilizing the available space for the conventional spark plug.

With increasing interest to reduce the dependency on gasoline and diesel, alternative energy source like compressed natural gas (CNG) is a viable option for internal combustion engines. Spark-ignited (SI) CNG engine is the simplest way to utilize CNG in engines, but direct injection (DI) Diesel-CNG dual-fuel engine is known to offer improvement in combustion efficiency and reduction in exhaust gases. Dual-fuel engine has characteristics similar to both SI engine and diesel engine which makes the combustion process more complex. This paper reports the computational fluid dynamics simulation of both DI dual-fuel compression ignition (CI) and SI CNG engines. In diesel-CNG dual-fuel engine simulations and comparison to experiments, attention was on ignition delay, transition from auto-ignition to flame propagation and heat released from the combustion of diesel and gaseous fuel, as well as relevant pollutants emissions.

In a study using a single-cylinder engine a significant potential in fuel efficiency and emission reduction was found for stratified operation of a high pressure natural gas direct injection (DI) spark ignition (SI) engine. The control of the mixture formation process appeared to be critical to ensure stable inflammation of the mixture. Therefore, optical investigations of the mixture formation were performed on a geometric equivalent, optically accessible single-cylinder engine to investigate the correlation of mixture formation and inflammability. The two optical measurement techniques infrared (IR) absorption and laser-induced fluorescence (LIF) were employed. Mid-wavelength IR absorption appeared to be qualified for a global visualization of natural gas injection; LIF allows to quantify the equivalence ratio inside a detection level. While LIF measurements require complex equipment, the IR setup consists merely of a black body heater and a mid-wavelength sensitive IR camera.

Worldwide diesel fuels differ in their composition and therefore in thermo-physical properties. Some of these properties are known to have little effect on the combustion process. Others, like the cetane number, have dramatic influence on the combustion formation and thus on the heat release rate and more important the formation of soot and NOx. In an experiment series various commercially available fuel types, like EN 590 [1], ASTM D975 [2] and JIS K 2204 [3], have been compared to alternative diesel fuels such as FAME, GtL and premium diesel fuel with increased cetane number. A specially designed research injector was used in order to provide full optical access to one single fuel jet injected and combusted in a constant volume vessel. First, the liquid fuel phase propagation has been investigated by means of Mie-scattering and the liquid penetration depth and the spray cone angle have been evaluated.

Modern concepts of downsized DI gasoline engines set up high requirements on the injection system to meet the emission targets. The fundamental knowledge and understanding of spray propagation physics are essential for the development of nozzles and injection strategies, due to reduced displacements in combination with the continuing trend of elevated fuel pressures. A detailed analysis of micro- and macroscopic spray parameters was carried out using a multihole solenoid driven DI injector. The measurements were performed in a continuously scavenged pressure chamber with full optical access. Fuel pressure up to 38MPa and backpressures in a range from 0.03 - 0.2 MPa were varied. Optical investigations were done by Shadowgraphy imaging and Phase Doppler Anemometry. The combination of micro- and macroscopic spray results are used to discuss the propagation behaviour of gasoline spray.

Hydrogen engines represent an economic alternative to fuel cells for future energy scenarios based on Liquid Organic Hydrogen Carriers (LOHC). This scenario incorporates LOHCs to store hydrogen from fluctuating renewable energy sources and deliver it to decentralised power generation units. Hydrogen engines were deeply investigated in the past decade and the results show efficiencies similar to CI engines. Due to the low energy density and tendency towards pre-ignition of hydrogen, the key element to reach high efficiency and a safe operation is a direct injection of the hydrogen. Because high injection pressure is not available in practical applications or would reduce the possible driving range, a low injection pressure is favourable. The low density leads to large flow cross sections inside the injector, similar to CNG direct injectors. So far, some research CNG and hydrogen low pressure direct injectors were investigated, but no commercial injector is available.

Modern direct injection spark ignition (DISI) engine concepts have the drawback of higher particulate matter emission as compared to port fuel injection concepts. Especially, when driven with biofuels, the operation of DISI engines requires a deeper insight into particulate formation processes. In this study a modern optical accessible DISI engine is used. Pure isooctane, ethanol, E20 (20vol% of ethanol in isooctane) and E85 were investigated as fuels. Simultaneous OH*-chemiluminescence and soot radiation imaging was conducted by a high-speed camera system in order to separate premixed combustion with the sooting combustion. Furthermore, a laser-induced incandescence (LII) sensor was used to measure exhaust elementary carbon mass concentration. Systematically, operation points were chosen, which correspondent to the main sooting mechanisms, poolfire, mixture inhomogeneities and global low air-fuel ratio. Furthermore, they were compared to a homogenous charge combustion strategy.

Cylinder deactivation is a technology seeing increased automotive deployment in light of more demanding fuel economy and emissions requirements. Examples of current production systems include GM's Active Fuel Management and Chrysler's Multi-Displacement System, both of which provide one fixed level of deactivation. Dynamic Skip Fire (DSF), in which the number of fired cylinders is continuously varied to match the torque demand, offers significantly increased fuel savings over a wider operating range than the current production systems. One of the biggest challenges in implementing cylinder deactivation is developing strategies to provide acceptable Noise, Vibration and Harshness (NVH); this paper discusses those challenges and the methodologies developed. This work covers theoretical root causes; proposed metrics to quantify the NVH level; algorithmic and physical mitigation methods; and both subjective and objective evaluation results.

Surrogates for JP-8 have been developed in the high temperature gas phase environment of gas turbines. In diesel engines, the fuel is introduced in the liquid phase where volatility plays a major role in the formation of the combustible mixture and autoignition reactions that occur at relatively lower temperatures. In this paper, the role of volatility on the combustion of JP-8 and five different surrogate fuels was investigated in the constant volume combustion chamber of the Ignition Quality Tester (IQT). IQT is used to determine the derived cetane number (DCN) of diesel engine fuels according to ASTM D6890. The surrogate fuels were formulated such that their DCNs matched that of JP-8, but with different volatilities. Tests were conducted to investigate the effect of volatility on the autoignition and combustion characteristics of the surrogates using a detailed analysis of the rate of heat release immediately after the start of injection.

The need for using alternative fuel sources continues to grow as industry looks towards enhancing energy security and lowering emissions levels. In order to capture the potential of these megatrends, this study focuses on the relationship between ignition energy, thermal efficiency, and combustion stability of a 0.5 L single cylinder engine powered by compressed natural gas (CNG) at steady state operation. The goal of the experiment was to increase ignition energy at fixed lambda values to look for gains in thermal efficiency. Secondly, a lambda sweep was performed with criteria of maintaining a 4% COVIMEP by increasing the ignition energy until an appropriate threshold for stable combustion was found. The engine performance was measured with a combustion analysis system (CAS), to understand the effects of thermal efficiency and combustion stability (COVIMEP). Emissions of the engine were measured with an FTIR.

Development of in-cylinder spray targeting, plume penetration and atomization of the gasoline direct-injection (GDi) multi-hole injector is a critical component of combustion developments, especially in the context of the engine downsizing and turbo-charging trend that has been adopted in order to achieve the European target CO2, US CAFE, and concomitant stringent emissions standards. Significant R&D efforts are directed towards the optimization of injector nozzle designs in order to improve spray characteristics. Development of accurate predictive models is desired to understand the impact of nozzle design parameters as well as the underlying physical fluid dynamic mechanisms resulting in the injector spray characteristics. This publication reports Large Eddy Simulation (LES) analyses of GDi single-hole skew-angled nozzles, with β=30° skew (bend) angle and different nozzle geometries.