Search Results

Piston wetting can be isolated from the other sources of HC emissions from DISI engines by operating the engine predominantly on a gaseous fuel and using an injector probe to impact a small amount of liquid fuel on the piston top. This results in a marked increase in HC emissions. In a previous study, we used a variety of pure liquid hydrocarbon fuels to examine the influence of fuel volatility and structure on the HC emissions due to piston wetting. It was shown that the HC emissions correspond to the Leidenfrost effect: fuels with very low boiling points yield high HCs and those with a boiling point near or above the piston temperature produce much lower HCs. All of these prior tests of fuel effects were performed at a single operating condition: the Ford World Wide Mapping Point (WWMP). In the present study, the effects of load and engine speed are examined.

An optical access engine was used to image the liquid film evaporation off the piston of a simulated direct injected gasoline engine. A directional injector probe was used to inject liquid fuel (gasoline, i-octane and n-pentane) directly onto the piston of an engine primarily fueled on propane. The engine was run at idle conditions (750 RPM and closed throttle) and at the Ford World Wide Mapping Point (1500 RPM and 262 kPa BMEP). Mie scattering images show the liquid exiting the injector probe as a stream and directly impacting the piston top. Schlieren imaging was used to show the fuel vaporizing off the piston top late in the expansion stroke and during the exhaust stroke. Previous emissions tests showed that the presence of liquid fuel on in-cylinder surfaces increases engine-out hydrocarbon emissions.

The mixture preparation process was investigated in a direct-injected, 4-valve, SI engine under motored conditions. The engine had a transparent cylinder liner that allowed the fuel spray to be imaged using laser sheet Mie scattering. A fiber optic probe was used to measure the vapor phase fuel concentration history at the spark plug location between the two intake valves. The fuel injector was located on the cylinder axis. Two flow fields were examined; the stock configuration (tumble index 1.4) and a high tumble (tumble index 3.4) case created using shrouded intake valves. The fuel spray was visualized with the engine motored at 750 and 1500 RPM. Start of injection timings of 90°, 180° and 270° after TDC of intake were examined. The imaging showed that the fuel jet is greatly distorted for the high tumble condition, particularly at higher engine speeds. The tumble was large enough to cause significant cylinder wall wetting under the exhaust valves for some conditions.

In premixed turbulent combustion models, two mechanisms have been used to explain the increase in the flame speed due to the turbulence. The newer explanation considers the full range of turbulence scales which wrinkle the flame front so as to increase the flame front area and, thus, the flame propagation speed. The fractal combustion model is an example of this concept. The older mechanism assumes that turbulence enables the penetration of unburned mixtures across the flame front via entrainment into the burned mixture zone. The entrainment combustion or eddy burning model is an example of this mechanism. The results of experimental studies of combustion regimes and the flame structures in SI engines has confirmed that most combustion takes place at the wrinkled flame front with additional combustion taking place in the form of flame fingers or peninsulas.

Predictions of the Fractal Engine Simulation code were compared with SI engine data in a previous paper. These comparisons were extremely good except for the single data set available at a low engine speed. Because of uncertainty regarding whether the lack of agreement for this case resulted from some difficulty with the experimental data or was due to lack of proper speed dependence in the model, additional comparisons are made for a range of speeds from 300-1500 rpm. The fractal burning model is a turbulence driven model (i.e., driven primarily by the turbulence intensity) that divides the combustion process into four sequential phases: 1) kernel formation, 2) early flame growth, 3) fully developed turbulent flame propagation, and 4) end of combustion. The kernel formation process was not included in the previous version of this model, but was found to be required to predict engine speed effects.

Researchers in the field of turbulent combustion have found fractal geometry to be a useful tool for describing and quantifying the nature of turbulent flames. This paper describes and compares several techniques for the fractal analysis of two dimensional (2-D) turbulent flame images. Four methods of fractal analysis were evaluated: the Area Method, the Box Method, the Caliper Method, and the Area-Caliper Method. These techniques were first applied to a computer-generated fractal image having a known fractal dimension and known cut-offs. It was found that a “window” effect can cause the outer cut-off to be underestimated. The Caliper Method was found to suffer from noise arising from the statistical nature of the analysis. The Area-Caliper Method was found to be superior to the other methods. The techniques were applied to two types of flame images obtained in a spark ignition engine: Mie scattering from particles seeded in the flow and laser induced fluorescence of OH.

Initial investigations of a new type of high energy ignitor for I.C. engines are described. The ignitor is a miniaturized railgun, or “railplug.” The railplug produces a relatively large mass of high velocity plasma. These characteristics may be advantageous for initiating combustion in a number of different applications. Unlike a plasma jet ignitor, the railplug plasma is driven not only by thermodynamic expansion, but by electromagnetic forces as well. Four experimental railplug designs were evaluated using schlieren and shadowgraphy visualization to examine plasma movement and shape. Railplug current and voltage were also measured. One railplug consisting of two unenclosed parallel rails was used to demonstrate the electromagnetically induced motion of the plasma at ambient conditions. Schlieren photos showed that the plasma plume moves strongly in the direction of the electromagnetic Lorentz forces.