Search Results

Momentum conservation is a principle rule that affects the behaviour of vapour jet and liquid spray penetration. The air entrainment and mixture formation processes are dominated by the momentum transferred from the fuel to the ambient gas. Thus, it is a significant factor in the development of spray and jet penetration. This mixture formation process is well described for small-scale passenger car injectors; however, it has to be investigated in more detail for large-scale injector nozzles. The current work provides qualitative and quantitative results of spray and jet parameters in a constant volume combustion chamber (CVC). Two optical methods have been utilized to evaluate spray and jet details: Schlieren photography as a method to visualize the jet penetration and cone angle as well as Mie scattering for the phase change evaluation and the determination of liquid spray parameters.

To address stricter emission limits, GDI develops to increased fuel pressure. Current gasoline injectors are already operating at a pressure of up to 35 MPa and an elevation is still promising lower particle emissions and increased efficiency. There have been only few studies of GDI sprays at pressures >50 MPa published. Contrary, in diesel engines injection pressure up to 250 MPa are common. GDI and diesel injector designs limit liquid penetration in different ways to avoid wall wetting, which has a negative impact on emissions in GDI combustion concepts. With elevated fuel pressure the question arises which design concept limits the penetration depth more effectively. To investigate the properties of high pressure sprays, a GDI injector (100 MPa max. fuel pressure) and an injector with diesel-like design are compared. High speed Shadowgraphy and Schlieren technique are used to gather information of liquid and vapor phase propagation.

The nozzle geometry of fuel injectors has a strong influence on turbulences and pressure gradients within the nozzle flow. The flow situation at the nozzle outlet determines the spray propagation into the ambient atmosphere. This spray penetration is critical for gasoline direct injection (GDI) systems. When the spray penetration is too high, it can cause wall and cylinder impingement, which increases particle emissions drastically. However, prediction of fuel spray propagation in dependency of nozzle hole geometry is difficult due to the large difference in scale between the nozzle flow and the spray development. Because of this, spray measurements with varying nozzle geometry parameters and statistical evaluation of these datasets are useful for the future development of fuel injectors. In this study, shadowgraphy measurements of real-size single-hole glass nozzles are presented. The nozzles cover a wide range of geometry parameters relevant to a GDI system.

Continued improvement in the combustion process of internal combustion engines is necessary to reduce fuel consumption, CO2 emissions, and criteria emissions for automotive transportation around the world. In this paper, test results for the Gen3X Gasoline Direct Injection Compression Ignition (GDCI) engine are presented. The engine is a 2.2L, four-cylinder, double overhead cam engine with compression ratio ~17. It features a “wetless” combustion system with a high-pressure direct injection fuel system. At low load, exhaust rebreathing and increased intake air temperature were used to promote autoignition and elevate exhaust temperatures to maintain high catalyst conversion efficiency. For medium-to-high loads, a new GDCI-diffusion combustion strategy was combined with advanced single-stage turbocharging to produce excellent low-end torque and power. Time-to-torque (TT) simulations indicated 90% load response in less than 1.5 seconds without a supercharger.

In DISI engines spray distribution and atomization directly influence mixture formation, the quality of combustion and the resulting emissions. Constant Volume Chambers (CVC) are commonly used to characterize sprays of gasoline injectors. The CVCs provide good optical access but the flow condition of the engine cannot be reproduced. Optically accessible engines in contrast deliver realistic flow conditions but have restricted optical access. In former investigations we compared the spray propagation of different injectors in constant volume chambers and in optical accessible engines. These results showed a clear difference of the spray propagation in the CVC and the engine, especially at high charge motion conditions in the engine. To find an appropriate way to investigate the impact of different charge motion a flow channel was built with adjustable crossflow velocities from 5-50 m/s. The spray propagation during the injection process was measured with high-speed shadowgraphy.

The automotive industry is facing tremendous challenges to improve fuel economy and emissions of the internal combustion engine. In the US, 2025 standards for fuel economy and CO2 emissions are extremely stringent. Simultaneously, vehicles must comply with new US Tier 3 emissions standards. In all market segments, there is a need for very clean and efficient engines operating on gasoline fuels. Gasoline Direct Injection Compression Ignition (GDCI) has been under development for several years and significant progress has been realized. As part of two US DOE programs, Delphi has developed a third generation GDCI engine that utilizes partially premixed compression ignition. The engine features an innovative “wetless”, low-temperature, combustion system with the latest high-pressure GDi injection system. The system was developed using extensive simulation and engine testing.

The fuel spray behavior in the near nozzle region of a gasoline injector is challenging to predict due to existing pressure gradients and turbulences of the internal flow and in-nozzle cavitation. Therefore, statistical parameters for spray characterization through experiments must be considered. The characterization of spray velocity fields in the near-nozzle region is of particular importance as the velocity information is crucial in understanding the hydrodynamic processes which take place further downstream during fuel atomization and mixture formation. This knowledge is needed in order to optimize injector nozzles for future requirements. In this study, the results of three experimental approaches for determination of spray velocity in the near-nozzle region are presented. Two different injector nozzle types were measured through high-speed shadowgraph imaging, Laser Doppler Anemometry (LDA) and X-ray imaging.

Three jet fuel surrogates were compared against their target fuels in a compression ignited optical engine under a range of start-of-injection temperatures and densities. The jet fuel surrogates are representative of petroleum-based Jet-A POSF-4658, natural gas-derived S-8 POSF-4734 and coal-derived Sasol IPK POSF-5642, and were prepared from a palette of n-dodecane, n-decane, decalin, toluene, iso-octane and iso-cetane. Optical chemiluminescence and liquid penetration length measurements as well as cylinder pressure-based combustion analyses were applied to examine fuel behavior during the injection and combustion process. HCHO* emissions obtained from broadband UV imaging were used as a marker for low temperature reactivity, while 309 nm narrow band filtered imaging was applied to identify the occurrence of OH*, autoignition and high temperature reactivity.

The second generation 1.8L Gasoline Direct Injection Compression Ignition (GDCI) engine was built and tested using RON91 gasoline. The engine is intended to meet stringent US Tier 3 emissions standards with diesel-like fuel efficiency. The engine utilizes a fulltime, partially premixed combustion process without combustion mode switching. The second generation engine features a pentroof combustion chamber, 400 bar central-mounted injector, 15:1 compression ratio, and low swirl and squish. Improvements were made to all engine subsystems including fuel injection, valve train, thermal management, piston and ring pack, lubrication, EGR, boost, and aftertreatment. Low firing friction was a major engine design objective. Preliminary test results indicated good improvement in brake specific fuel consumption (BSFC) over the first generation GDCI engines, while meeting targets for engine out emissions, combustion noise and stability.

In a study using a single-cylinder engine a significant potential in fuel efficiency and emission reduction was found for stratified operation of a high pressure natural gas direct injection (DI) spark ignition (SI) engine. The control of the mixture formation process appeared to be critical to ensure stable inflammation of the mixture. Therefore, optical investigations of the mixture formation were performed on a geometric equivalent, optically accessible single-cylinder engine to investigate the correlation of mixture formation and inflammability. The two optical measurement techniques infrared (IR) absorption and laser-induced fluorescence (LIF) were employed. Mid-wavelength IR absorption appeared to be qualified for a global visualization of natural gas injection; LIF allows to quantify the equivalence ratio inside a detection level. While LIF measurements require complex equipment, the IR setup consists merely of a black body heater and a mid-wavelength sensitive IR camera.

Worldwide diesel fuels differ in their composition and therefore in thermo-physical properties. Some of these properties are known to have little effect on the combustion process. Others, like the cetane number, have dramatic influence on the combustion formation and thus on the heat release rate and more important the formation of soot and NOx. In an experiment series various commercially available fuel types, like EN 590 [1], ASTM D975 [2] and JIS K 2204 [3], have been compared to alternative diesel fuels such as FAME, GtL and premium diesel fuel with increased cetane number. A specially designed research injector was used in order to provide full optical access to one single fuel jet injected and combusted in a constant volume vessel. First, the liquid fuel phase propagation has been investigated by means of Mie-scattering and the liquid penetration depth and the spray cone angle have been evaluated.

A 1.8L Gasoline Direct Injection Compression Ignition (GDCI) engine was tested over a wide range of engine speeds and loads using RON91 gasoline. The engine was operated with a new partially premixed combustion process without combustion mode switching. Injection parameters were used to control mixture stratification and combustion phasing using a multiple-late injection strategy with GDi-like injection pressures. At idle and low loads, rebreathing of hot exhaust gases provided stable compression ignition with very low engine-out NOx and PM emissions. Rebreathing enabled reduced boost pressure, while increasing exhaust temperatures greatly. Hydrocarbon and carbon monoxide emissions after the oxidation catalyst were very low. Brake specific fuel consumption (BSFC) of 267 g/kWh was measured at the 2000 rpm-2bar BMEP global test point.

Modern concepts of downsized DI gasoline engines set up high requirements on the injection system to meet the emission targets. The fundamental knowledge and understanding of spray propagation physics are essential for the development of nozzles and injection strategies, due to reduced displacements in combination with the continuing trend of elevated fuel pressures. A detailed analysis of micro- and macroscopic spray parameters was carried out using a multihole solenoid driven DI injector. The measurements were performed in a continuously scavenged pressure chamber with full optical access. Fuel pressure up to 38MPa and backpressures in a range from 0.03 - 0.2 MPa were varied. Optical investigations were done by Shadowgraphy imaging and Phase Doppler Anemometry. The combination of micro- and macroscopic spray results are used to discuss the propagation behaviour of gasoline spray.

Modern direct injection spark ignition (DISI) engine concepts have the drawback of higher particulate matter emission as compared to port fuel injection concepts. Especially, when driven with biofuels, the operation of DISI engines requires a deeper insight into particulate formation processes. In this study a modern optical accessible DISI engine is used. Pure isooctane, ethanol, E20 (20vol% of ethanol in isooctane) and E85 were investigated as fuels. Simultaneous OH*-chemiluminescence and soot radiation imaging was conducted by a high-speed camera system in order to separate premixed combustion with the sooting combustion. Furthermore, a laser-induced incandescence (LII) sensor was used to measure exhaust elementary carbon mass concentration. Systematically, operation points were chosen, which correspondent to the main sooting mechanisms, poolfire, mixture inhomogeneities and global low air-fuel ratio. Furthermore, they were compared to a homogenous charge combustion strategy.

In previous work, Gasoline Direct Injection Compression Ignition (GDCI) has demonstrated good potential for high fuel efficiency, low NOx, and low PM over the speed-load range using RON91 gasoline. In the current work, a four-cylinder, 1.8L engine was designed and built based on extensive simulations and single-cylinder engine tests. The engine features a pent roof combustion chamber, central-mounted injector, 15:1 compression ratio, and zero swirl and squish. A new piston was developed and matched with the injection system. The fuel injection, valvetrain, and boost systems were key technology enablers. Engine dynamometer tests were conducted at idle, part-load, and full-load operating conditions. For all operating conditions, the engine was operated with partially premixed compression ignition without mode switching or diffusion controlled combustion.

Development of in-cylinder spray targeting, plume penetration and atomization of the gasoline direct-injection (GDi) multi-hole injector is a critical component of combustion developments, especially in the context of the engine downsizing and turbo-charging trend that has been adopted in order to achieve the European target CO2, US CAFE, and concomitant stringent emissions standards. Significant R&D efforts are directed towards the optimization of injector nozzle designs in order to improve spray characteristics. Development of accurate predictive models is desired to understand the impact of nozzle design parameters as well as the underlying physical fluid dynamic mechanisms resulting in the injector spray characteristics. This publication reports Large Eddy Simulation (LES) analyses of GDi single-hole skew-angled nozzles, with β=30° skew (bend) angle and different nozzle geometries.

Natural gas has been considered to be one of the most promising alternative fuels due to its lower NOx and soot emissions, less carbon footprint as well as attractive price. Furthermore, higher octane number makes it suitable for high compression ratio application compared with other gaseous fuels. For better economical and lower emissions, a turbocharged, four strokes, direct injection, high pressure common rail diesel engine has been converted into a diesel/natural gas dual-fuel engine. For dual-fuel engine operation, natural gas as the main fuel is sequentially injected into intake manifold, and a very small amount of diesel is directly injected into cylinder as the ignition source. In this paper, a dual-fuel electronic control unit (ECU) based on the PowerPC 32-bit microprocessor was developed. It cooperates with the original diesel ECU to control the fuel injection of the diesel/natural gas dual-fuel engine.

Differences in thermo-physical parameters of fuels have high impact on the ignition, combustion and emission. Pure rapeseed FAME and diesel fuel with a cetane number of 60 have been compared to reference fuel. In an optical accessible vessel the fuels have been injected in order to investigate the spray, the ignition and soot formation. The high cetane number fuel showed similar behavior in spray phase to the reference fuel but the FAME fuel is more present at all operating points due to low volatile fuel components. The ignition and combustion process was investigated via chemical luminescence (CL) and laser induced incandescence (LII). In engine investigations a reduced ignition delay is detected in case of high cetane-number. The more sensitive optical techniques show differences in the combustion process. The ignition behavior of the reference fuel and the increased cetane number fuel were similar until the cetane increaser of the high cetane fuel came into effect.

Understanding the causal loop from injection to combustion in modern direct injection engines is essential to improve combustion and reduce emissions. In this work, the section from injection to fuel-evaporation in this causal loop was investigated using different optical measurement techniques, with a focus on drop size measurements using Phase Doppler Anemometry (PDA). One spray jet of a modern DISI multi-hole injector was investigated using gasoline RON 95 fuel and two single component alkane fuels (n-hexane / n-decane). In a first step the macroscopic spray formation and propagation of this spray jet were studied using a 2D-Mie-scattering technique in an optical injection chamber at homogenous charge DISI conditions. Furthermore, the droplet size distribution and mean diameter were determined spatially and temporally resolved for an ambient pressure of 0.3MPa and different ambient temperature (323K / 423K / 523K) conditions in the optical chamber using Phase Doppler Anemometry.

The interaction between a combusting diesel spray and a wall at temperatures of 700K and 735K was investigated in a combustion chamber using optical measurement techniques. The temperatures were chosen as they appear in the range of the maximum piston surface temperatures of the latest production engines. Combustion was investigated with a dual camera setup, which is designed to take simultaneous pictures of the UV flame luminosity (FL_UV) and the visible flame luminosity (FL_VIS). The FL_UV is used to measure lean or stoichiometric combustion. The FL_VIS is capable of detecting the thermally excited soot. Mie scattering is used to study the liquid fuel phase. It was found that there is almost no FL_VIS signal visual in the 700K case, but a very strong signal in the 735K case. In general, one might expect that higher wall temperatures lead to an improved mixture formation and, consequently, lower soot production. However, the opposite was detected.