Search Results

An ultra-lightweight piston and conrod without small end bush, combined with a ring pack designed for minimized friction is analyzed and demonstrated as an optimized power cylinder system in a high performance gasoline engine. Component and system analysis for optimizing the design, materials used and design features are reviewed, along with durability, NVH and friction testing results. Results are compared to other benchmark power cylinder system components for weight, performance and value.

It is well known that lubricating oil consumption (LOC) is much affected by the cylinder bore deformation occurring within internal combustion engines. There are few analytical reports, however, of this relationship within internal combustion engines in operation. This study was aimed at clarifying the relationship between cylinder bore deformation and LOC, using a conventional in-line four-cylinder gasoline engine. The rotary piston method developed by the author et al. was used to measure the cylinder bore deformation of the engine’s cylinder #3 and cylinder #4. In addition, the sulfur tracer method was applied to measure LOC of each cylinder. LOC was also measured by changing ring tension with a view to taking up for discussion how piston ring conforms to cylinder, and how such conformability affects LOC. Their measured results were such that the cylinder bore deformation was small in the low engine load area and large in the high engine load area.

The relationship between piston ring and out side of diameter (hereon referred to as OD) wear of ring has not been fully analyzed. In this study, the relationship between the ring OD wear and ring friction force during the break-in period, where ring OD wear occurs in a short period of time, was analyzed. After 20 hours of firing test, Friction mean effective Pressure (hereon referred to as FMEP) of nitrided ring having OD wear was 1.6kPa higher than that of Physical Vapor Deposition (hereon referred to as PVD) ring having little amount of wear (hereon referred to as “no OD wear”). In addition, lubricating condition of piston system during break-in period was also analyzed in this study. When plateau-honing cylinder was used, the FMEP showed an increasing trend over a 20-hour period of firing test. The cause of this increasing trend is the deterioration of lubricating condition of the piston skirt.

This paper deals with the friction performance results for various new concept piston skirt profiles. The program was conducted under the assumption that friction performance varies by the total amount of oil available at each crank angle in each stroke and the instantaneous distribution of the oil film over the piston skirt area. In previous papers [1,2] it was that lower friction designs would be expected to show higher skirt slap noise. This paper discusses the correlation between friction and skirt slap for each new concept profile design. Finally, this paper explains the friction reduction mechanism for the test samples for each stroke of the engine cycle by observing the skirt movement and oil lubrication pattern using a visualization engine.

By observation through a glass window, the effect of side surface sealing ability of piston ring on the increase of oil consumption for light load and at medium engine speed range was confirmed. In each engine stroke, effects of ring motion on oil consumption were predicted by simulation and the flow of oil around piston ring was observed during actual firing engine operation through a visualization window with a test engine. Importance of the side surface sealing ability of piston ring on oil consumption and effect of small width top ring with positive twist for second ring collapse were reconfirmed.

Automobile engines have undergone continuous improvements over the years in terms of higher output, lower pollutant emission, and lower fuel consumption. With recent steep rise in crude oil price, consumer interest in fuel economy of automobiles has increased. With such interest, lowering fuel consumption appears to be the issue that currently needs to be tackled. The piston ring and piston friction were measured with floating liner, we confirmed that wear of piston ring running surface influenced friction. It was confirmed by this study that main cause of break in is decrease in liner surface roughness and piston ring OD wear. Additionally, this paper indicated that friction decreased by preventing piston ring OD wear in the process of break in.

Due to increasing economic and environmental performance requirements of internal combustion engines, piston manufacturers now focus more on lower friction designs. One factor strongly influencing the friction behavior of pistons is the dynamic interaction between lubricating oil, cylinder bore and piston. Therefore, the dynamic effect of the oil film in the gap between the liner and piston has been studied, using a single cylinder engine equipped with a sapphire window. This single cylinder engine was also equipped with a floating liner, enabling real-time friction measurement, and directly linking the oil film behavior to friction performance of pistons.

The objective was to rank piston friction and noise for three piston architectures at three cold clearance conditions. Piston secondary motion was measured using four gap sensors mounted on each piston skirt to better understand the friction and noise results. One noticeable difference in friction performance from conventional designs was as engine speed increased the friction force during the expansion stroke decreased. This was accompanied by relatively small increases in friction force during the other strokes so Friction Mean Effective Pressure (FMEP) for the whole cycle was reduced. Taguchi's Design of Experiment method was used to analyze the variances in friction and noise.

The authors et al. developed a unique single cylinder diesel engine equipped with a floating liner device for the measurement of piston friction force, aimed at the clarification of the relationship between the multiple fuel injections and the state of piston lubrication. Using this engine, the effects of the post fuel injections on the state of piston lubrication have been checked under this study, according to the variation in the piston friction force. As a result, it is verified that the oil film on the cylinder near the top dead center is diluted immediately with the injected fuel, and that the piston lubrication deteriorates more than anticipated even for the case using the SAE 5W/30 oil, compared with the case where the SAE 0W/20 oil with a lower viscosity is used.

The effect of local lubricant viscosity on the temperature and thickness of oil film on a piston ring in a diesel engine is analyzed by using the Reynolds equation, and unsteady and two-dimensional energy equation with heat generated from viscous dissipation. The oil film viscosity for a multi-grade oil is then estimated by using the local oil film temperature and the local shear rate. Moreover, the heat transfer between ring and liner surfaces is examined. The oil film thickness calculated from this method is lesser than that of the case where the viscosity is based on the liner temperature and the mean shear rate. Maximum values of heat transfer at the ring and liner surfaces are obtained at the vicinity of crank angle where the oil film thickness is at a minimum.

Aiming at the improvement in piston lubrication and the reduction of piston friction loss under this study, piston friction forces of cylinders with different surface roughness and treatment methods have been measured by means of a floating liner method, and the piston surface conditions have been also observed. As a result, it is found that the piston lubrication can be markedly improved by reducing the cylinder surface roughness. It is also verified that the deterioration in lubrication can be reduced even if some low viscosity oil is used, and the effect on the friction loss reduction becomes greater by reducing the piston surface roughness. On the other hand, it is found that many small vertical flaws are generated on the cylinder surface by reducing the surface roughness. In order to cope with this problem, etching and DLC (Diamond Like Carbon) coating have been tested as the surface treatments. As a result, it is confirmed that DLC coating is effective for the above.

Although various factors affecting oil consumption of an internal combustion engine can be considered, a technique to predict the amount of oil consumed within a cylinder that passes across a running surface of a ring was developed in this study. In order to predict the effect of cylinder deformation on oil consumption, a simple and easy technique to calculate the oil film thickness in deformed cylinder was proposed. For this technique, the piston ring was assumed to be a straight beam, and the beam bends with ring tension, gas pressure, and oil film pressure. From the calculated oil film thickness, amount of oil passing across the running surface of the TOP ring and into the combustion chamber was calculated. The calculated results were then compared to the oil film thickness of the ring and oil consumption measured during engine operation, and their validity was confirmed.

A study was conducted to understand the effects the specifications of the crank-slider mechanism have on piston friction losses. The information obtained through the study is believed to be useful information for reducing the piston friction. A single-cylinder spark-ignited gasoline engine was designed and constructed to have not only a real-time piston friction measurement system using the floating liner method, but also provisions to facilitate changing the specifications of the crank-slider mechanism. This paper describes the study results obtained under various engine-operating conditions and reports the parametric test results of three crank ratios and five crankshaft-offset amounts tested.

This study has been conducted aiming at an experimental verification of the ring collapse phenomena that occurs in a taper faced second ring of a direct fuel injection type truck diesel engine. The oil film thickness of the second ring, the ring axial motion and the inter-ring pressure have been measured under various operating conditions of engine. As a result, it is verified that the back pressure of the second ring becomes lower than the second land pressure, and that the second ring oil film becomes extremely thick temporarily where the second ring contacts with the ring groove upper surface. It is also verified that blow-by passes through the second ring where the oil film of the second ring becomes thick. Hence it is highly probable that the collapse of the second ring has occurred at that time.

This study has been conducted aiming at reductions of piston slap noise and piston friction loss, and effects of lubricating oil supply between the piston skirt and cylinder on diesel engine have been verified through a series of experiments. Namely, lubricating oil was supplied forcibly into the piston skirt from outside of engine, and its effects on the cylinder block vibration, piston friction force, slap motion and oil consumption have been measured. As a result, it has been verified that the supply of a small amount of oil (6mL/min) to the piston skirt reduces about 50 % of the block vibration caused by the piston slap motion in idling operation, and about 20 % of the piston friction loss in full load operation. Furthermore it has verified without giving any significant adverse effect on oil consumption.

Oil film thicknesses of the piston top ring and the second ring of a truck diesel engine have been measured simultaneously by embedding capacitance type clearance sensors in the ring sliding surfaces. Owing to the above, several phenomena such as the variation in oil film thickness of each ring in one cycle, correlation between the rings, difference in oil film thickness between the thrust and counter thrust-sides, effects of engine operating conditions on oil film thickness, etc. have been determined. Efforts have been also made to analyze the causes of such phenomena according to the measured results of piston slap motion and ring motions, and the calculated results of oil film thickness.

Exhaust-gas recirculation (EGR) causes the piston ring and cylinder liners of a diesel engine to suffer abnormal wear. The present study aimed at making clear the mechanism of wear which is induced by soot in the EGR gas. The piston ring has been chrome plated and the cylinder was made of boron steadite cast iron. Detailed observations of the ring sliding surfaces and that of the wear debris contained in lubricating oil were carried out. As a result, it was found that the wear of the top ring sliding surfaces identify abrasive wear without respect to the presence of EGR by steadite on the cylinder liner sliding surface. In addition, it is confirmed in a cutting test that soot mixed lubricating oil improved in performance as cutting oil. Based on these results, we proposed the hypothesis in the present study that ring wear is accelerated at EGR because abrasive wear increases due to a lot of soot mixed into lubricating oil improving the performance of lubricating oil as cutting oil.

Offsetting the crankshaft axis with respect to the cylinder axis has been thought to be a method to reduce piston side force[1]. Hence the piston friction is expected to be reduced. An automotive manufacturer has already used the crankshaft offset for a production gasoline engine to improve fuel economy. The authors have conducted research into the effect of crankshaft offset on the piston friction. A single-cylinder engine was modified to have a crankshaft offset. Piston frictional force was measured in real-time by using a floating liner method. In addition, laser-induced fluorescence (LIF) technique was employed to measure oil film thickness on the piston skirt area, and a gap sensor was used to measure piston motion. As a result, the authors concluded that the effect of crankshaft offset on piston friction could not be explained only by its effect on the piston side force. In accordance with the measurement results, crankshaft offset changed piston slap motion.

This paper describes measurements of oil film thickness of piston ring packages which have different oil control rings. The oil film thickness measurements were taken at three points, namely, the piston thrust side, front side and rear side, by the Laser Induced Fluorescence Method(LIF). One of the main findings is that the oil film thickness on the thrust side varies greatly from cycle to cycle, while cyclic variations are smaller on the front and rear sides. This difference is due to the smaller inclination of the oil control rings on the front and rear sides, compared with that on the thrust side. It is also found that oil consumption has a good correlation with oil film thickness on the thrust side and that the thrust side oil film thickness becomes thinner as the oil ring becomes narrower.

Exhaust-gas recirculation (EGR) causes the piston rings and cylinder liners of a Diesel engine to suffer abnormal wear on the sliding parts. The present study aimed at making clear such abnormal wear structurally by examining the state of lubrication of the piston with a floating liner method, observing directly a visualized cylinder and experimenting on a Diesel engine for wear. As a result, it was confirmed that soot in EGR gas would change a lot the characteristics of the piston friction force. There are two mechanisms: one directly enters the sliding surfaces, and the other enters the ring rear, applying more load to them. It was also confirmed that the level of wear on the piston ring would vary to a large extent as the state of lubrication changed.