Search Results

Partially Premixed Combustion (PPC) has demonstrated substantially higher efficiency compared to conventional diesel combustion (CDC) and gasoline engines (SI). By combining experiments and modeling the presented work investigates the underlying reasons for the improved efficiency, and quantifies the loss terms. The results indicate that it is possible to operate a HD-PPC engine with a production two-stage boost system over the European Stationary Cycle while likely meeting Euro VI and US10 emissions with a peak brake efficiency above 48%. A majority of the ESC can be operated with brake efficiency above 44%. The loss analysis reveals that low in-cylinder heat transfer losses are the most important reason for the high efficiencies of PPC. In-cylinder heat losses are basically halved in PPC compared to CDC, as a consequence of substantially reduced combustion temperature gradients, especially close to the combustion chamber walls.

The acoustic and performance characteristics of an automotive centrifugal compressor are studied on a steady-flow turbocharger test bench, with the goal of advancing the current understanding of compression system instabilities at the low-flow range. Two different ducting configurations were utilized downstream of the compressor, one with a well-defined plenum (large volume) and the other with minimized (small) volume of compressed air. The present study measured time-resolved oscillations of in-duct and external pressure, along with rotational speed. An orifice flow meter was incorporated to obtain time-averaged mass flow rate. In addition, fast-response thermocouples captured temperature fluctuations in the compressor inlet and exit ducts along with a location near the inducer tips.

Using a 3 liter, 4 valves per cylinder, V6 Diesel engine model, this study investigates late intake valve closing (LIVC) time in an effort to reduce the fuel consumption of the engine. Two different intake cam duration technologies for diesel engines are evaluated using a 1-D engine simulation software code. The first method utilized for duration control delays the effective closing of the intake valve by moving one intake cam lobe with respect to the other baseline intake cam lobe. In the second method, the closing of both intake valves is delayed by the introduction of an adjustable dwell period during the closing portion of the valve motion. During this mid-lift dwell period, the lift is held at a constant value until it goes into the closing phase. The systems are evaluated and compared at 4 operating points of varying engine speed and load. At each operating point, while engine load is held constant, intake valve closing time is varied.

In our introductory paper on the VEMB system (SAE 2010-01-1222) we discussed the concept of a divided exhaust period turbocharging system controlled by a concentric cam system, and we presented several fixed speed/load point sets of results that demonstrated the expected BSFC benefits. The BSFC reductions (2.5% to 4%) correlated to reduction in pumping work and to improvement in combustion phasing at knock-limited points from substantial reductions in Residual Gas Fraction compared to the conventionally-boosted baseline engine. In this paper we present additional results from engine tests in the areas of full-load performance and emissions with and without Scavenge-sourced EGR. To demonstrate the WOT performance potential of a VEMB engine, we show the effect of turbocharger matching steps, with results that exceed the baseline engine output across the engine speed range.

Trying to improve the modern diesel engine's NOx/soot tradeoff without giving up fuel economy continues to be a core target for the engine development community. One of the options not yet fully investigated for the diesel is applying variable valve events to the engine breathing process. Already used in some heavy-duty applications, late intake valve closing has long been regarded as a possible strategy for small diesel engines. Single-cylinder tests applying fully variable valve events have demonstrated potential but also raised doubts about VVA benefits on automotive size diesel engines. Full engine testing using realistic valve train technology is seen as key to judging its true performance because it covers not only combustion benefits but also influences like engine pumping on emissions and CO₂. Different to past publications, this paper focuses on testing a production feasible variable valve train technology on a fully instrumented modern Common Rail diesel engine.

The unsteady surge behavior of a turbocharger compression system is studied computationally by employing a one-dimensional engine simulation code. The system modeled represents a new turbocharger test stand consisting of a compressor inlet duct breathing from ambient, a centrifugal compressor, an exit duct connected to an adjustable-volume plenum, followed by another duct which incorporates a control valve and an orifice flow meter before exhausting to ambient. Characteristics of mild and deep surge are captured as the mass flow rate is reduced below the stability limit, including discrete sound peaks at low frequencies along with their amplitudes in the compressor (downstream) duct and plenum. The predictions are then compared with the experimental results obtained from the cold stand placed in a hemi-anechoic room.

The behavior of the compression system in turbochargers is studied with a one-dimensional engine simulation code. The system consists of an upstream compressor duct open to ambient, a centrifugal compressor, a downstream compressor duct, a plenum, and a throttle valve exhausting to ambient. The compression system is designed such that surge is the low mass flow rate instability mode, as opposed to stall. The compressor performance is represented through an extrapolated steady-state map. Instead of incorporating a turbine into the model, a drive torque is applied to the turbocharger shaft for simplification. Unsteady compression system mild surge physics is then examined computationally by reducing the throttle valve diameter from a stable operating point. Such an increasing resistance decreases the mass flow rate through the compression system and promotes surge.

Naturally aspirated HCCI operation is typically limited to medium load operation (∼ 5 bar net IMEP) by excessive pressure rise rate. Boosting can provide the means to extend the HCCI range to higher loads. Recently, it has been shown that HCCI can achieve loads of up to 16.3 bar of gross IMEP by boosting the intake pressure to more than 3 bar, using externally driven compressors. However, investigating HCCI performance over the entire speed-load range with real turbocharger systems still remains an open topic for research. A 1 - D simulation of a 4 - cylinder 2.0 liter engine model operated in HCCI mode was used to match it with off-the-shelf turbocharger systems. The engine and turbocharger system was simulated to identify maximum load limits over a range of engine speeds. Low exhaust enthalpy due to the low temperatures that are characteristic of HCCI combustion caused increased back-pressure and high pumping losses and demanded the use of a small and more efficient turbocharger.

It has been clearly demonstrated separately, that the application of both Dual Cam Phasers (DCP) and External Cooled EGR systems are highly beneficial to improving the efficiency of highly-boosted GDI engines. DCP systems can optimize the volumetric efficiency at WOT conditions, improve boost and transient response at low engine speeds, and provide internal EGR at low RPM part-load conditions. External cooled EGR has been demonstrated to dramatically improve the fuel consumption, lower turbine inlet temperature, and improve emissions at high power conditions. In previous investigations by the BorgWarner Engine Systems Group, we showed that full engine speed/load range EGR coverage can be obtained by combining High Pressure Loop and Low Pressure Loop external EGR systems with a DCP strategy.

The current direction for Diesel combustion system development is towards homogenization, in order to reduce particulate and NOx emissions. However, a strong increase of carbon monoxide emissions (CO) is frequently noted in combination with enhanced homogenization. Therefore, the current investigation focuses on a detailed analysis of the particulate - CO trade-off using a laser-optical and multidimensional CFD investigation of the combustion process of a swirl HSDI system. The CFD methodology involves reduced kinetics for soot formation and oxidation and a three-step CO model. These models are validated by a detailed comparison to optical measurements of flow, spray penetration and the spatial distribution of soot, temperature and oxygen concentration. The results obtained show that high concentrations of CO occur as an intermediate combustion reaction product. Subsequently, CO and soot are oxidized in large areas of the combustion chamber.

Variable Compression Ratio (VCR) technology has long been recognized as a method of improving Spark Ignition (SI) engine fuel economy. The Pressure Reactive Piston (PRP) assembly features a two-piece piston, with a piston crown and separate piston skirt which enclose a spring set between them. The unique feature is that the upper piston reacts to the cylinder pressure, accommodating rapid engine load changes passively. This mechanism effectively limits the peak pressures at high loads without an additional control device, while allowing the engine to operate at high compression ratio during low load conditions. Dynamometer engine testing showed that Brake Specific Fuel Consumption (BSFC) improvement of the PRP over the conventional piston ranged from 8 to 18 % up to 70% load. Knock free full load operation was also achieved. The PRP equipped engine combustion is characterized by reverse motion of the piston crown near top dead center and higher thermal efficiency.

This paper discusses the compression ratio influence on maximum load of a Natural Gas HCCI engine. A modified Volvo TD100 truck engine is controlled in a closed-loop fashion by enriching the Natural Gas mixture with Hydrogen. The first section of the paper illustrates and discusses the potential of using hydrogen enrichment of natural gas to control combustion timing. Cylinder pressure is used as the feedback and the 50 percent burn angle is the controlled parameter. Full-cycle simulation is compared to some of the experimental data and then used to enhance some of the experimental observations dealing with ignition timing, thermal boundary conditions, emissions and how they affect engine stability and performance. High load issues common to HCCI are discussed in light of the inherent performance and emissions tradeoff and the disappearance of feasible operating space at high engine loads.

Natural gas quality, in terms of the volume fraction of higher hydrocarbons, strongly affects the auto-ignition characteristics of the air-fuel mixture, the engine performance and its controllability. The influence of natural gas composition on engine operation has been investigated both experimentally and through chemical kinetic based cycle simulation. A range of two component gas mixtures has been tested with methane as the base fuel. The equivalence ratio (0.3), the compression ratio (19.8), and the engine speed (1000 rpm) were held constant in order to isolate the impact of fuel autoignition chemistry. For each fuel mixture, the start of combustion was phased near top dead center (TDC) and then the inlet mixture temperature was reduced. These experimental results have been utilized as a source of data for the validation of a chemical kinetic based full-cycle simulation.