Search Results

In the past years, stringent emission regulations for Internal Combustion (IC) engines produced a large amount of research aimed at the development of innovative combustion methodologies suitable to simultaneously reduce fuel consumption and engine-out emissions. Previous research demonstrates that the goal can be obtained through the so-called Low Temperature Combustions (LTC), which combine the benefits of compression-ignited engines, such as high compression ratio and unthrottled lean operation, with a properly premixed air-fuel mixture, usually obtained injecting gasoline-like fuels with high volatility and longer ignition delay. Gasoline Partially Premixed Combustion (PPC) is a promising LTC technique, mainly characterized by the high-pressure direct-injection of gasoline and the spontaneous ignition of the premixed air-fuel mixture through compression, which showed a good potential for the simultaneous reduction of fuel consumption and emissions in CI engines.

This work focuses on the development and validation of a data-driven model capable of predicting the maximum in-cylinder pressure during the operation of an internal combustion engine, with the least possible computational effort. The model is based on two parameters, one that represents engine load and another one the combustion phase. Experimental data from four different gasoline engines, two turbocharged Gasoline Direct Injection Spark Ignition, a Naturally Aspirated SI and a Gasoline Compression Ignition engine, was used to calibrate and validate the model. Some of these engines were equipped with technologies such as Low-Pressure Exhaust Gas Recirculation and Water Injection or a compression ignition type of combustion in the case of the GCI engine. A vast amount of engine points were explored in order to cover as much as possible of the operating range when considering automotive applications and thus confirming the broad validity of the model.

This work focuses on the effects of cooled Low Pressure EGR and Water Injection observed by conducting experimental tests consisting mainly of Spark Advance sweeps at different cooled LP-EGR and WI rates. The implications on combustion and main engine performance indexes are then analysed and modelled with a control-oriented approach, showing that combustion duration and phase and exhaust gas temperature are the main affected parameters. Results show that cooled LP-EGR and WI have similar effects, being the associated combustion speed decrease the main cause of exhaust gas temperature reduction. Experimental data is used to identify control-oriented polynomial models able to capture the effects of LP-EGR and WI on both these aspects. The limitations of LP-EGR are also explored, identifying maximum compressor volumetric flow and combustion stability as the main ones.

The continuous development of modern Internal Combustion Engine (ICE) management systems is mainly aimed at complying with upcoming increasingly stringent regulations throughout the world. Performing an efficient combustion control is crucial for efficiency increase and pollutant emissions reduction. These aspects are even more crucial for innovative Low Temperature Combustions (such as RCCI), mainly due to the high instability and the high sensitivity to slight variations of the injection parameters that characterize this kind of combustion. Optimal combustion control can be achieved through a proper closed-loop control of the injection parameters. The most important feedback quantities used for combustion control are engine load (Indicated Mean Effective Pressure or Torque delivered by the engine) and center of combustion (CA50), i.e. the angular position in which 50% of fuel burned within the engine cycle is reached.

Upcoming more stringent emission regulations throughout the world pose a real challenge, especially in regard to Diesel systems for passenger cars, where the need of additional after-treatment has a big impact in terms of additional system costs and available packaging space. Therefore, the need for strategies that allow managing combustion towards lower emissions, that require a precise control of the combustion outputs, is definitely increasing. Acoustic emission of internal combustion engines contains a large amount of information related to engine behavior and working conditions. Mechanical noise and combustion noise are usually the main contributions to the noise produced by an engine. In particular, recent research from the same authors of this paper demonstrated that combustion noise can be used as an indicator of the combustion that is taking place inside the combustion chamber and therefore as a reference for the control strategy.

The need for strategies that allow managing combustion in an adaptive way has recently widely increased. Especially Diesel engines aimed for clean combustion require a precise control of the combustion outputs. Acoustic emission of internal combustion engines contains a lot of information related to engine behavior and working conditions. Mechanical noise and combustion noise are usually the main contributions to the noise produced by an engine. Combustion noise in particular can be used as an indicator of the combustion that is taking place inside the combustion chamber and therefore as a reference for the control strategy. This work discusses the correlations existing between in cylinder combustion and the acoustic emission radiated by the engine and presents a possible approach to use this signal in the engine management system for control purposes.

Nowadays the high competition reached by the automotive market forces Original Equipment Manufacturers (OEMs) towards innovative solutions. Strict emission standards and fuel economy targets make the work hard to be accomplished. Therefore modern engines feature complex architecture and embed new devices for Exhaust Gas Recirculation (EGR), turbocharging (e.g. multi-stage compressors), gas after-treatment (e.g. the Selective Catalyst Reduction (SCR)) and fuel injection (either high or low pressure). In this context the Engine Management System (EMS) plays a fundamental role to optimize engine operation. The paper deals with fuel spray and combustion simulation by a multi-zone phenomenological model aimed at the steady-state optimal tuning of the injection pattern.

International regulations continuously restrict the standards for the exhaust emissions from automotive engines. In order to comply with these requirements, innovative control and diagnosis systems are needed. In this scenario the application of methodologies based on the in-cylinder pressure measurement finds widespread applications. Indeed, almost all engine thermodynamic variables useful for either control or diagnosis can be derived from the in-cylinder pressure. Apart for improving the control accuracy, the availability of the in-cylinder pressure signal might also allow reducing the number of existing sensors on-board, thus lowering the equipment costs and the engine wiring complexity. The paper focuses on the detection of the engine thermal state, which is fundamental to achieve suitable control of engine combustion and after-treatment devices.

The purpose of this paper is to present some innovative techniques developed for an unconventional utilization of currently standard exhaust sensors, such as HEGO, UEGO, and NOx probes. In order to comply with always more stringent legislation about pollutant emissions, intake-exhaust systems are becoming even more complex and sophisticated, especially for CI engines, often including one or two UEGO sensors and a NOx sensor, and potentially equipped with both short-route and long-route EGR. Within this context, the effort to carry out novel methods for measuring the main exhaust gas dynamic properties exploiting sensors installed for different purposes, could be useful both for control applications, such as EGR rates estimation, or cost reduction, minimizing the on-board devices number. In this work, a gray-box model for measuring the gas mass flow rate, based on standard NOx sensor operating parameters of its heating circuit, is analyzed.

Automotive engines and control systems are more and more sophisticated due to increasingly restrictive environmental regulations. Particularly in both diesel and SI lean-burn engines NOx emissions are the key pollutants to deal with and sophisticated Engine Management System (EMS) strategies and after-treatment devices have to be applied. In this context, the in-cylinder oxygen mass fraction plays a key-role due its direct influence on the NOx formation mechanism. Real-time estimation of the intake O₂ charge enhances the NOx prediction during engine transients, suitable for both dynamic adjustments of EMS strategies and management of aftertreatment devices. The paper focuses on the development and experimental validation of a real-time estimator of O₂ concentration in the intake manifold of an automotive common-rail diesel engine, equipped with turbocharger and EGR system.

New and upcoming exhaust emissions regulations and fuel consumption reduction requirements are forcing the development of innovative and particularly complex intake-engine-exhaust layouts. Especially in the case of Compression Ignition (CI) engines, the HC-CO-NOx-PM after-treatment system is becoming extremely expensive and sophisticated, and the necessity to further reduce engine-out emission levels, without significantly penalizing fuel consumption figures, may lead to the adoption of intricate and challenging intake-exhaust systems configurations. The adoption of both long- and short-route Exhaust Gas Recirculation (EGR) systems is one example of such situation, and the need to precisely measure (or estimate) mass flow rates in the various elements of the gas exchange circuit is one of the consequences.

Future regulations on pollutant emissions will impose a drastic cut on Diesel engines out-emissions. For this reason, the development of closed-loop combustion control algorithms has become a key factor in modern Diesel engine management systems. Diesel engines out-emissions can be reduced through a highly premixed combustion portion in low and medium load operating conditions. Since low-temperature premixed combustions are very sensitive to in-cylinder thermal conditions, the first aspect to be considered in newly developed Diesel engine control strategies is the control of the center of combustion. In order to achieve the target center of combustion, conventional combustion control algorithms correct the measured value varying main injection timing. A further reduction in engine-out emissions can be obtained applying an appropriate injection strategy.

The paper deals with the steady-state optimal tuning of control variables for an automotive turbocharged Diesel engine. The optimization analysis is based on an engine simulation model, composed of a control oriented model of turbocharger integrated with a predictive multi-zone combustion model, which allows accounting for the impact of control variables on engine performance, NOx and soot emissions and turbine outlet temperature. This latter strongly affects conversion efficiency of after treatment devices therefore its estimation is of great interest for both control and simulation of tailpipe emissions. The proposed modeling structure is aimed to support the engine control design for common-rail turbocharged Diesel engines with multiple injections, where the large number of control parameters requires a large experimental tuning effort.

Modern internal combustion engine control systems require on-board evaluation of a large number of quantities, in order to perform an efficient combustion control. The importance of optimal combustion control is mainly related to the requests for pollutant emissions reduction, but it is also crucial for noise, vibrations and harshness reduction. Engine system aging can cause significant differences between each cylinder combustion process and, consequently, an increase in vibrations and pollutant emissions. Another aspect worth mentioning is that newly developed low temperature combustion strategies (such as HCCI combustion) deliver the advantage of low engine-out NOx emissions, however, they show a high cylinder-to-cylinder variation. For these reasons, non uniformity in torque produced by the cylinders in an internal combustion engine is a very important parameter to be evaluated on board.

Nowadays requirements towards a reduction in fuel consumption and pollutant emissions of Internal Combustion Engines (ICE) keep on pushing manufacturers to improve engines performance through the enhancement of existing subsystems (e.g.: electronic fuel injection, air systems) and the introduction of specific devices (e.g.: exhaust gas recirculation systems, SCR, …). Modern systems require a combined design and application of different after-treatment devices. Mathematical models are useful tools to investigate the complexity of different system layouts, to design and to validate (HIL/SIL testing) control strategies for the after-treatment management. This study presents a mean value model of an exhaust system with SCR; it has been coupled with a common rail diesel engine combustion black box model (Neural Network based). So, dedicated models for exhaust pipes, oxidation catalyst, diesel particulate filter and selective catalytic converter are developed.

Multi-jet injection strategies open significant opportunities for the combustion management of the modern diesel engine. Splitting up the injection process into 5 steps facilitates the proper design of the combustion phase in order to obtain the desired torque level, whilst attempting a reduction in emissions, particularly in terms of NOx. Complex 3-D models are needed in the design stage, where components such as the injector or combustion chamber shape have to be determined. Alternatively, zero-dimensional approaches are more useful when fast interpretation of experimental data is needed and an optimization of the combustion process should be obtained based on actual data. For example, zero-dimensional models allow a quick choice of optimum control settings for each engine operating condition, avoiding the need to test all the possible combinations of engine control parameters.