Search Results

The effects of intake pressure (Pin), start of injection (SOI), injection pressure (Pinj), injection split ratio (Qsplit), internal and external exhaust gas recirculation rates were varied to optimize several key parameters at a partially pre-mixed combustion low load/low speed condition using CFD. These include indicated specific fuel consumption (ISFC), combustion phasing (CA50), maximum rate of pressure rise (MRPR), maximum cylinder pressure (Pmax), indicated specific NOx (sNOx), indicated specific hydrocarbons (sHC) and Filter Smoke Number (FSN) emissions. Low-load point (6 bar indicated mean effective pressure (IMEP), 1500 revolutions per minute (RPM)) was selected where Pin varied between 1.25 and 1.5 bar, SOI between -100 and -10 crank angle degree (CAD) after top dead center (aTDC), Pinj between 100 and 200 bar, split ratio between 0 and 0.5, EGR between 0 and 45% and internal EGR measured by rebreathing valve height was varied between 0 and 4.5 mm.

Due to experimental challenges, combustion of diesel-like jets has rarely been characterized by laser-based quantitative multiscalar measurements. In this work, recently developed laser diagnostics for combustion temperature and the concentrations of CO, O2, and NO are applied to a diesel-like jet, using a highly oxygenated fuel. The diagnostic is based on spontaneous Raman scattering (SRS) and laser-induced fluorescence (LIF) methods. Line imaging yields multiscalar profiles across the jet cross section. Measurements turn out to be particularly accurate, because near-stoichiometric combustion occurs in the central region of the jet. Thereby, experimental cross-influences by light attenuation and interfering emissions are greatly reduced compared to the combustion of conventional, sooting diesel fuel jets. This is achieved by fuel oxygenation and enhanced premixing.

This study investigated dual-fuel operation with a light duty Diesel engine over a wide engine load range. Ethanol was hereby injected into the intake duct, while Diesel was injected directly into the cylinder. At low loads, high ethanol shares are critical in terms of combustion stability and emissions of unburnt hydrocarbons. As the load increases, the rates of heat release become problematic with regard to noise and mechanical stress. At higher loads, an advanced injection of Diesel was found to be beneficial in terms of combustion noise and emissions. For all tests, engine-out NOx emissions were kept within the EU-6.1 limit.

Maintaining low NOx emissions over the operating range of diesel engines continues to be a major issue. However, optical measurements of nitric oxide (NO) are lacking particularly in the core of diesel jets, i.e. in the region of premixed combustion close to the spray axis. This is basically caused by severe attenuation of both the laser light and fluorescent emission in laser-induced fluorescence (LIF) applications. Light extinction is reduced by keeping absorption path lengths relatively short in this work, by investigating diesel jets in a combustion vessel instead of an engine. Furthermore, the NO-detection threshold is improved by conducting 1-d line measurements instead of 2-d imaging. The NO-LIF data are corrected for light attenuation by combined LIF and spontaneous Raman scattering. The quantified maximum light attenuation is significantly lower than in comparable previous works, and its wavelength dependence is surprisingly weak.

With increasing interest in new biofuel candidates, 1-octanol and di-n-butylether (DNBE) were presented in recent studies. Although these molecular species are isomers, their properties are substantially different. In contrast to DNBE, 1-octanol is almost a gasoline-type fuel in terms of its auto-ignition quality. Thus, there are problems associated with engine start-up for neat 1-octanol. In order to find a suitable glow-plug position, mixture formation is studied in the cylinder under almost idle operating conditions in the present work. This is conducted by planar laser-induced fluorescence in a high-speed direct-injection optical diesel engine. The investigated C8-oxygenates are also significantly different in terms of their evaporation characteristics. Thus, in-cylinder mixture formation of these two species is compared in this work, allowing conclusions on combustion behavior and exhaust emissions.

Pilot injection (PI) during the negative-valve-overlap (NVO) period is one method to improve control of combustion in gasoline controlled auto-ignition engines. This is generally attributed to both chemical and thermal effects. However, there are little experimental data on active species formed by the combusting PI and their effect on main combustion in real engines. Thus, it is the objective of the current study to apply and assess optical in-cylinder diagnostics for these species. Firstly, the occurrence and nature of combustion during the NVO period is investigated by spectrally-resolved multi-species flame luminescence measurements. OH*, CH*, HCO*, CO-continuum chemiluminescence, and soot luminosity are recorded. Secondly, spectrally-, spatially-, and cycle-resolved laser-induced fluorescence measurements of formaldehyde are conducted. It is attempted to find a cycle-resolved measure of the chemical effect of PI.

Legislative restrictions on the currently limited exhaust gas components and the future CO2 emissions limits have led to intensive research in the field of alternative fuels and innovative combustion approaches. Increased homogeneity of air-fuel mixture through advanced injection is one combustion approach, which potentially reduces engine-out nitrogen oxide and particulate emissions, with good fuel consumption in certain load ranges. Ignition characteristics under homogenous combustion conditions differ from those under heterogeneous conditions. Among other reasons, this is due to the increased role of low temperature chemistry with increasing homogeneity. The ignition behaviour of diesel fuels is characterised by the Cetane number (CN), which is, however, determined at significant higher temperatures than those prevalent during ignition under homogenous combustion. As a result, its relevance as a fuel characteristic number requires evaluation.

The residue and waste streams of existing industry offer feasible and sustainable raw materials for biofuel production. All kind of biomass contains carbon and hydrogen which can be turned into liquid form with suitable processes. Using hydrotreatment or Biomass-to-Liquid technologies (BTL) the liquid oil can be further converted into transportation biofuels. Hydrotreatment technology can be used to convert bio-oils and fats in to high quality diesel fuels that have superior fuel properties (e.g. low aromatic content and high cetane number) compared to regular diesel fuel and first generation ester-type diesel fuel. UPM has developed a new innovative technology based on hydrotreatment that can be used to convert Crude Tall Oil (CTO) into high quality renewable diesel fuel. This study concentrated on determining the functionality and possible effects of CTO based renewable diesel as a blending component on engine emissions and engine performance.

Recent research [21] has shown that the compression ignition concept where very low cetane fuels (RON between 70 and 85) are run in compression ignition (CI) mode has several advantages. The engine will be at least as efficient and clean as the current diesel engines but will have a less complicated after-treatment system. The optimum fuel will be less processed and therefore simpler to make compared to current gasoline or diesel fuels. Naphtha, which is a product of the initial distillation of petroleum, is one such fuel. It provides a path to mitigate the global demand imbalance between heavier and lighter fuels that is otherwise projected. Since naphtha requires much less processing in the refinery than either gasoline or diesel [23], there is an additional benefit in terms of well-to-wheel CO2 emissions and overall energy consumed. Partially premixed charge compression ignition combustion with such a low cetane fuel has usually been investigated with a diesel engine base.

Demand for transport energy is growing but this growth is skewed heavily toward commercial transport, such as, heavy road, aviation, marine and rail which uses heavier fuels like diesel and kerosene. This is likely to lead to an abundance and easy availability of lighter fractions like naphtha, which is the product of the initial distillation of crude oil. Naphtha will also require lower energy to produce and hence will have a lower CO₂ impact compared to diesel or gasoline. It would be desirable to develop engine combustion systems that could run on naphtha. Many recent studies have shown that running compression ignition engines on very low Cetane fuels, which are very similar to naphtha in their auto-ignition behavior, offers the prospect of developing very efficient, clean, simple and cheap engine combustion systems. Significant development work would be required before such systems could power practical vehicles.

More stringent emissions standards along with higher fuel economy demands have obliged auto makers to develop technical solutions that exploit synergistic features from gasoline and diesel engines. To minimize NOx and soot trade-off, diesel powertrain has been developed to adopt increasingly complex and expensive technology such as extremely high pressure fuel injection systems, low pressure EGR, and variable valve timing. These attempts are associated with promoting Partially Premixed Charge Compression Ignition (PPC-CI) combustion via increasing mixing time and ignition delay. Alternatively, PPC-CI combustion can be achieved easier by using fuels with higher resistance to auto-ignition than conventional diesel fuel. Previous work has demonstrated the possibility of reducing the cost of future diesel after-treatment systems by using gasoline-like fuels.

Recently, a consistent mixing model for the two-way coupling of a CFD code and a zero-dimensional multi-zone code was developed. This work allowed for building an interactively coupled CFD-multi-zone approach that can be used to model HCCI combustion. In this study, the interactively coupled CFD-multi-zone approach is applied to PCCI combustion in a 1.9l FIAT GM Diesel engine. The physical domain in the CFD code is subdivided into multiple zones based on one phase variable (fuel mixture fraction). The fuel mixture fraction is the dominant quantity for the description of nonpremixed combustion. Each zone in the CFD code is represented by a corresponding zone in the zero-dimensional multi-zone code. The zero-dimensional multi-zone code solves the chemistry for each zone, and the heat release is fed back into the CFD code. The thermodynamic state of each zone, and thereby the phase variable, changes in time due to mixing and source terms (e.g., vaporization of fuel, wall heat transfer).

Subject of this work is a simulation model for PCCI combustion that can be used in closed-loop control development. A detailed multi-zone chemistry model for the high-pressure part of the engine cycle is extended by a mean value model accounting for the gas exchange losses. The resulting model is capable of describing PCCI combustion with stationary excactness. It is at the same time very economic with respect to computational costs. The model is further extended by identified system dynamics influencing the stationary inputs. For this, a Wiener model is set up that uses the stationary model as a nonlinear system representation. In this way, a dynamic nonlinear model for the representation of the controlled plant Diesel engine is created.

Within a public founded project test cell investigations were undertaken to identify parameters which predominantly influence the development of critical deposits in injection nozzles. A medium-duty diesel engine was operated in two different coking cycles with a zinc-free lubricant. One of the cycles is dominated by rated power, while the second includes a wide area of the operation range. During the experiments the temperatures at the nozzle tip, the geometries of the nozzle orifice and fuel properties were varied. For a detailed analysis of the deposits methods of electron microscopy were deployed. In the course of the project optical access to all areas in the nozzle was achieved. The experiments were evaluated by means of the monitoring of power output and fuel flow at rated power. The usage of a SEM (scanning electron microscope) and a TEM (transmission electron microscope) revealed images of the deposits with a magnification of up to 160 000.

Subject of this work is the recently introduced extended Representative Interactive Flamelet (RIF) model for multiple injections. First, the two-dimensional laminar flamelet equations, which can describe the transfer of heat and mass between two-interacting mixture fields, are presented. This is followed by a description of the various mixture fraction and mixture fraction variance equations that are required for the RIF model extension accounting for multiple injection events. Finally, the modeling strategy for multiple injection events is described: Different phases of combustion and interaction between the mixture fields resulting from different injections are identified. Based on this, the extension of the RIF model to describe any number of injections is explained. Simulation results using the extended RIF model are compared against experimental data for a Common-Rail DI Diesel engine that was operated with three injection pulses.

In Common-Rail DI Diesel Engines, multiple injection strategies are considered as one of the methodologies to achieve optimum performance and emission reduction. However, multiple injections open a whole new horizon of parameters which affect the combustion process. These parameters include the number of injection events, the duration between the starts of each injection event, the splitting of the total fuel mass on the different injection events, etc. In the present work, the influence of the number of injection events and the influence of the duration between the starts of each injection event on emission levels are investigated. Combustion and pollutant formation were experimentally investigated in a Common-Rail DI Diesel engine. The engine was operated at conventional part-load conditions with 2000 rpm, no external EGR, and an injected fuel mass of 15 mg/cycle.

Representative Interactive Flamelets (RIF) have proven successful in predicting Diesel engine combustion. The RIF concept is based on the assumption that chemistry is fast compared to the smallest turbulent time scales, associated with the turnover time of a Kolmogorov eddy. The assumption of fast chemistry may become questionable with respect to the prediction of pollutant formation; the formation of NOx, for example, is a rather slow process. For this reason, three different approaches to account for NOx emissions within the flamelet approach are presented and discussed in this study. This includes taking the pollutant mass fractions directly from the flamelet equations, a technique based on a three-dimensional transport equation as well as the extended Zeldovich mechanism. Combustion and pollutant emissions in a Common-Rail DI Diesel engine are numerically investigated using the RIF concept. Special emphasis is put on NOx emissions.

Homogeneous Charge Compression Ignition (HCCI) is a combustion concept which has the potential for efficiency comparable to a DI Diesel engine with low NOx and soot emissions. However, HCCI is difficult to control, especially at low speeds and loads. One way to assist with combustion control and to extend operation to low speed and loads is to close the exhaust valve before TDC of the exhaust stroke, trapping and recompressing some of the hot residual. Further advantages can be attained by injecting the fuel into this trapped, recompressed mixture, where chemical reactions occur that improve ignitability of the subsequent combustion cycle. Even further improvement in the subsequent combustion cycle can be achieved by applying a spark, leading to a spark-assisted HCCI combustion concept.

Combustion and pollutant formation in a new recently introduced Common-Rail DI Diesel engine concept with roof-shaped combustion chamber and tumble charge motion are numerically investigated using the Representative Interactive Flamelet concept (RIF). A reference case with a cup shaped piston bowl for full load operating conditions is considered in detail. In addition to the reference case, three more cases are investigated with a variation of start of injection (SOI). A surrogate fuel consisting of n-decane (70% liquid volume fraction) and α-methylnaphthalene (30% liquid volume fraction) is used in the simulation. The underlying complete reaction mechanism comprises 506 elementary reactions and 118 chemical species. Special emphasis is put on pollutant formation, in particular on the formation of NOx, where a new technique based on a three-dimensional transport equation within the flamelet framework is applied.