Search Results

Objective: A friction rollover test was conducted as part of a rollover sensing project. This study evaluates vehicle and occupant responses in the test. Methods: A flat dolly carried a Saab 9-3 sedan laterally, passenger-side leading to a release point at 42 km/h (26 mph) onto a high-friction surface. The vehicle was equipped with roll, pitch and yaw gyros near the center of gravity. Accelerometers were placed at the vehicle center tunnel, A-pillar near the roof, B-pillar near the sill, suspension sub-frame and wheels. Five off-board and two on-board cameras recorded kinematics. Hybrid III dummies were instrumented for head and chest acceleration and upper neck force and moment. Belt loads were measured. Results: The vehicle release caused the tires and then wheel rims to skid on the high-friction surface. The trip involved roll angular velocities >300 deg/s at 0.5 s and a far-side impact on the driver’s side roof at 0.94 s. The driver was inverted in the far-side, ground impact.

A decade ago, James, et.al. published a detailed study of the available NASS data on severe rear impacts, with findings that “… stiffened or rigid seat backs will not substantially mitigate severe and fatal injuries in rear impacts.” No field accident study has since been advanced which refutes this finding. Advocates of rigidized seat backs often point to specific cases of severe rear impacts in which MAIS 4+ injuries are associated with seat back deformation, coupled with arguments supporting stiffer seatback designs. These arguments are generally based upon laboratory experiments with dummies in normal seating positions. Recent field accident data shows that generally, in collisions where the majority of societal harm is created, yielding seats continue to provide benefits, including those associated with whiplash associated disorders (WAD).

The original Malibu II study, conducted by Bahling et al, found that neck compression loading in rollover crashes is caused by the occupant moving toward the ground and therefore, roof crush was not causally related to the loading. Some have disputed this finding claiming that the occupant does not “dive toward the roof,” but rather, the roof “moves in” toward the occupant, and that roof deformation is the primary cause of cervical spine injuries in rollover crashes. The original study included a detailed analysis of film and force transducer data for 10 Potentially Injurious Impacts (PII's). This paper presents an independent analysis of these 10 PII's and one additional PII. This analysis uses the film and transducer data to evaluate the timing of roof deformation and neck loading, the magnitude of roof deformation at the time of peak neck load, and the motion of the vehicle and occupants in the inertial reference system.

Heavier, larger pickups and SUVs are bound to encounter lighter, smaller passenger vehicles in many future accidents. As the fleet has evolved to include more and more SUVs, their frontal structures are often indistinguishable from pickup fronts. Improvements in geometric compatibility features are crucial to further injury prevention progress in side impact. In corner crashes where modern bullet passenger car (PC) bumpers make appropriate geometrical overlap with target PC rocker panels, concentrated loads sometimes disrupt foam and plastic bumper corners, creating aggressive edges. In situations where sliding occurs along the structural interface, these sharp edges may slice through doors, panels and pillars. End treatments for such bumper beams should be designed to reduce this aggressive potential.

Based upon a review of the literature and new test data, the human and vehicle factors leading to head-to-roof contact in rollovers are quantified and illustrated. Vehicle design countermeasures and suggested areas of research are presented. Higher and stronger roofs and improved restraints must be analyzed as a system to evaluate the potential benefits in rollovers.

Field experience has consistently indicated that lap-only belts and lap-shoulder belts perform well and about equally in prevention of fatalities and serious injuries in the rear seating positions. Analyses based on overall usage and injury figures from the Fatal Analysis Reporting System (FARS), double-pair analysis of FARS data, and still older data bases have shown that, in the rear outboard seating positions, injury rates are about the same for lap-only and lap-shoulder belted crash occupants. Although sparse, recently available field data from the 1988-2001 National Analysis Sampling System / Crashworthiness Data System (NASS/CDS) files confirm the finding that, when used by rear seat occupants, lap-only belts perform about equally with lap-shoulder belts as countermeasures for serious and fatal injury in severe frontal crashes.

Understanding occupant kinematics is an important part of accident reconstruction, particularly with respect to injury causation. Injuries are generally sustained as the occupant interacts with the vehicle interior surfaces and is rapidly accelerated to the struck component's post-impact velocity. This paper describes some methods for assessing occupant kinematics in a collision, and discusses their limitations. A useful technique is presented which is based on free-body analysis and can be used to establish an occupant's path of motion relative to the vehicle, locate the point of occupant contact, and determine the occupant's velocity relative to that contact location.

Rollover accidents are responsible for a significant percentage of crash injuries. Increasing seat belt restraint use is the most effective way to reduce rollover injuries. Injuries to restrained occupants are also of interest. It has been suggested that head/neck injuries are caused by roof crush, and that modification to roof structures and seat belt systems would lead to a substantial reduction in severe rollover injuries. Field accident data and rollover testing are used to evaluate the relationship between roof crush, seat belt design, and severe rollover injuries.

The National Highway Traffic Safety Administration (NHTSA) has recently opened a rulemaking docket seeking comments on the design of automobile seats and their performance in rear Impacts. There are two philosophies of seat design: one advocates rigid seats, the other advocates seats which yield in a controlled manner. A review of the legislative history of seat back design standards indicates that yielding seats have historically been considered a better approach for passenger cars. The design characteristics of current production automobile seats are evaluated and show no significant changes over the past three decades. Concerns about the performance of rigid seat backs in real world rear impacts are discussed, specifically increased injury exposure due to ramping, rebound and out-of-position occupants.

Recent detailed field accident data are examined with regard to injuries associated with rear impacts. The distribution of “Societal Harm” associated with various injury mechanisms is presented, and used to evaluate the performance of current seat back and restraint system designs. Deformation associated with seat back yield is shown to be beneficial in reducing overall Societal Harm in rear impacts. The Societal Harm associated with ejection and contact with the vehicle rear interior (the two injury mechanisms addressed by a rigid seat approach), is shown to be minimal. The field accident data also confirm that restraint usage in rear impacts has a substantial injury-reducing effect. Laboratory tests and computer simulations were run to investigate the mechanism by which seat belts protect occupants in rear impacts.

Rear impacts in the crash test data base compiled by the NHTSA are analyzed and compared to the CRASH3 rear stiffness coefficients. The CRASH3 values do not represent the test data adequately. This is because the values were derived from limited data, and because some of the rear moving barrier test data were miscoded as fixed barrier tests. A review of the larger NHTSA data base does not support the CRASH3 assumption that vehicles of similar size (wheelbase) have similar rear stiffness characteristics. Therefore, it is important when reconstructing individual accidents to use crash test data specific to the vehicles involved. Repeated rear fixed barrier test data on four vehicles are analyzed to study the data trend at speeds below and above the NHTSA test data. Constant stiffness and constant force models are compared and a combination of the two is shown to fit available test data.

This paper summarizes work relating to the assessment of societal benefits of side impact protection. National Crash Severity Study (NCSS) and National Accident Sampling System (NASS) accident data technigues were reviewed with respect to the reliability of output information concerning the distribution of side impact accidents by impact severity and relationships between injury and impact severity. NCSS and NASS are confounded by errors and inadequacies, primarily as a result of improper accident reconstruction based upon the CRASH computer program. Based on review of several sample cases, it is believed that the NCSS/NASS files underestimate Lower severities and overestimate higher severities in side impact, with delta-V errors probably overestimated by 25-30 percent in the case of the more serious accidents. These errors cannot be properly quantified except on a case-by-case basis. They introduce unknown biases into NCSS/NASS.

An understanding of fundamental kinematic relationships among the several deforming surfaces of side-impacting bullet and target vehicle, occupant protection system and occupant is fundamental to rational design of crash injury counter-measures. Unfortunately, such understanding is not easy to achieve. Side impacts address the full range of bodily contacts and injuries in a way that challenges analysis. Each bodily area and organ requires individual consideration for adequate injury protection. This paper presents a simplified graphical analysis of occupant kinematics and injury exposure applied specifically to the NHTSA-proposed crabbed moving deformable barrier (MDB) compartment impact, as described in NHTSA's Notice of Proposed Rulemaking (NPRM) for Federal Motor Vehicle Safety Standard (FMVSS) 214, issued in January of 1988 [NHTSA 1988 (1)*]. Projections are offered regarding the potential of thoracic injury counter-measures.

Collision Safety Engineering, Inc. (CSE), has developed a test prototype system to protect occupants during lateral impacts. It is an inflatable system that offers the potential of improved protection from thoracic, abdominal and pelvic injury by moving an impact pad into the occupant early in the crash. Further, it shows promise for head and neck protection by deployment of a headbag that covers the major target areas of B-pillar, window space, and roofrail before head impact. Preliminary static and full-scale crash tests suggest the possibility of injury reduction in many real-world crashes, although much development work remains before the production viability of this concept can be established. A description of the system and its preliminary testing is preceded by an overview of side impact injury and comments on the recent NHTSA Rule Making notices dealing with side-impact injury.

The issues of front seat energy absorption and seat belt effectiveness are investigated first through the review of prior experimental and analytical studies of rear impact dynamics. These prior studies indicate that the current energy absorption characteristic of seats is a safety benefit. Prior efforts to construct a rigidized seat indicate that such designs are likely to be impractical due to excessive weight and cost. Additionally, these studies indicate that seat belts provide an important safety function in rear impacts. Static tests of production seats were conducted, added to an existing data base, and analyzed to better understand the strength and energy absorbing characteristics of production seats. Crash test results from the New Car Assessment Program as well as earlier test programs were analyzed to describe the response of occupants and seats in rear impact and the protective function of seat belts in such collisions.

Results of two studies concerning the interrelationship of velocity, compression and injury in blunt thoracic impact to anesthetized swine have been combined to provide a data base of forty-one experiments. impact velocity ranged from ∼8-30 m/s and applied normalized chest compression from ∼0.10-0.30. Experimental subjects were suspended in the spine-horizontal position and loaded midsternally through a 150 mm diameter, flat rigid disk on an impacting mass propelled upward from below. Measurements and computations included sternal and spinal accelerations, intracardiovascular overpressures, physiological responses, injury, as assessed by necropsy, and different forms of the velocity and compression exposure severity parameters. The significance of both compression and velocity as parameters of impact exposure severity is clearly demonstrated. Qualitatively, exacerbation of injury was seen when either variable was increased with the other held constant.

Vehicle accident reconstruction methods based on deformation energy are argued to be an increasingly valuable tool to the accident reconstructionist, provided reliable data, reasonable analysis techniques, and sound engineering judgement accompany their use. The evolution of the CRASH model of vehicle structural response and its corresponding stiffness coefficients are reviewed. It is concluded that the deformation energy for an accident vehicle can be estimated using the CRASH model provided that test data specific to the accident vehicle is utilized. Published stiffness coefficients for vehicle size categories are generally not appropriate. For the purpose of estimating vehicle deformation energy, a straight-forward methodology is presented which consists of applying the results of staged crash tests. The process of translating crush profiles to estimates of vehicle deformation energies and velocities is also discussed.

The relatively rare occurrence of injury or fatality in fuel-fed fires has received considerable attention in automotive safety rulemaking and products liability litigation. The literature related to fatalities associated with fire is confirmed by recent FARS data, and there are no reliable field data which confirm a need for further injury-reducing effect related to FMVSS 301. NHTSA has acknowledged this by removing crash fire rulemaking from its priorities plan. The police-reported crash fire data now available must be supplemented with in-depth investigation by trained teams before informed judgements can be made regarding further safety improvements with respect to crash fire injury.

A vehicle trajectory simulation called VTS has been developed as an aid for reconstruction of automobile accidents. The two dimensional vehicle has longitudinal, lateral and yaw degrees of freedom, a point mass at the center of gravity) yaw inertia about the center of gravity and four contact points (“tires”) which can be arbitrarily positioned. No collision or aerodynamic forces are modeled. The traction surface is represented as a flat plane with a specified nominal friction coefficient. Several quadrilateral “patches” may be applied to the surface to change the friction coefficient in specific regions. User vehicle control consists of timewise tables for steering angle and traction coefficient for each of the four wheels. When used individually or in conjunction with other computer modules, VTS provides a convenient, accurate modular tool for trajectory simulation.

This project covers one facet of a program to develop a mechanical model for characterizing the time history of local forces on the zygomatic, maxillary and mandible regions of the human face during a frontal collision. Two mechanical devices to measure the forces on crash dummies during testing were designed, constructed and tested. The devices employed cantilever beams equipped with strain gauges. Both devices were subjected to a series of drop tests onto various materials. Time histories were compared to those obtained from cadaver experiments. While the data obtained from this testing appears to be similar to the cadaver data, further improvements and modifications will make the model much more useful.