Refine Your Search

Date

Date

Topic

Topic

Medical, health, and wellness Data management SAE IC Powertrain Steering Committee

Search Results

Viewing 1 to 20 of 27
12Next >Last >>
Sort by published
Standard

Multiposition Small Engine Exhaust System Fire Ignition Suppression
2020-10-06
CURRENT
J335_202010
This SAE Recommended Practice establishes equipment and test procedures for determining the performance of spark arrester exhaust systems of multiposition small engines (<19 kW) used in portable applications, including hand-held, hand-guided, and backpack mounted devices. It is not applicable to spark arresters used in vehicles or stationary equipment.
Standard

Spark Arrester Test Procedure for Large Size Engines
2013-03-26
HISTORICAL
J342_201303
This SAE Recommended Practice establishes equipment and procedures for the evaluation of the effectiveness and other performance characteristics of spark arresters or turbochargers used on the exhaust system of large engines normally used in a railroad locomotive, stationary power plant, and other similar applications. This document does not cover applications requiring flame arresting, exhaust gas cooling, or isolation from explosive gases. Two test methods are presented: a laboratory test using ambient air (cold test) and an engine test using exhaust gases (hot test). The hot test is preferred. Arresters tested by the provisions of this document can be expected to perform as tested when tilted no more than 45 degrees from their normal position. Test results from a spark arrester or turbocharger evaluated by the hot test can be applied to different engines of similar design, provided the data shows it to be effective in the applicable flow ranges.
Standard

Engine Flywheel Housings with Sealed Flanges
2012-10-23
CURRENT
J1172_201210
This SAE Recommended Practice defines flywheel housing flange configurations for applications requiring "O" ring sealing of the flange pilot bore. Table 1 and Figure 1 show dimensions that are different from those in SAE J617. All other dimensions and tolerances of SAE J617 apply.
Standard

Industrial Power Take-Offs With Driving Ring-Type Overcenter Clutches
2012-10-23
CURRENT
J621_201210
This SAE Standard defines installation dimensions of industrial power take-offs with driving ring-type overcenter clutches. Table 1 and Figure 1 give dimensions for power take-offs. For dimensions and tolerances of power take-off flanges and flywheels, see SAE J617 and J620, respectively.
Standard

Multiposition Small Engine Exhaust System Fire Ignition Suppression
2012-10-23
HISTORICAL
J335_201210
This SAE Recommended Practice establishes equipment and test procedures for determining the performance of spark arrester exhaust systems of multiposition small engines (<19 kW) used in portable applications, including hand-held, hand-guided, and backpack mounted devices. It is not applicable to spark arresters used in vehicles or stationary equipment.
Standard

Housing Internal Dimensions for Single- and Two-Plate Spring-Loaded Clutches
2012-05-31
CURRENT
J373_201205
This SAE Recommended Practice defines the minimum internal dimensions for clutch housings to provide adequate clearance for single- and two-plate spring-loaded clutches. (See Figure 1.) Consult SAE J617 for housing flange dimensions. Consult SAE J618 and J619 for spring-loaded clutch flywheel dimensions F and G and other dimensional data. Table 1 provides housing minimum internal dimensions for single- and two-plate spring-loaded clutches.
Standard

Flywheels for Two-Plate Spring-Loaded Clutches
2012-05-31
CURRENT
J619_201205
This SAE Recommended Practice defines flywheel configuration to promote standardization of flywheels for dry spring-loaded clutches. Clutches to fit flywheels with configurations per this document may not be commercially available. Availability should be ascertained prior to flywheel design Figure 1 and Table 1A.
Standard

Thrust Washers – Design and Application
2011-06-13
CURRENT
J924_201106
This SAE Standard presents the basic size and tolerance information for the design and manufacture of thrust washers. In most cases, the standard employs nominal figures in both metric and inch-pound units and, therefore, does not necessarily provide exact equivalents.
Standard

Engine and Transmission Dipstick Marking
2011-06-13
CURRENT
J614_201106
This SAE Recommended Practice provides information useful in the marking of engine and transmission dipsticks used for fluid level indication.
Standard

Design Guide for Formed-in-Place Gaskets
2008-07-08
CURRENT
J1497_200807
This SAE Recommended Practice presents information which is intended as a guide for proper designing, selection, application, and servicing of liquid, formed-in-place gasket (FIPG) materials.
Standard

ENGINE AND TRANSMISSION DIPSTICK MARKING
1995-06-29
HISTORICAL
J614_199506
This SAE Recommended Practice provides information useful in the marking of engine and transmission dipsticks used for fluid level indication.
Standard

INDUSTRIAL POWER TAKE-OFFS WITH DRIVING RING-TYPE OVERCENTER CLUTCHES
1995-03-08
HISTORICAL
J621_199503
This SAE Standard defines installation dimensions of industrial power take-offs with driving ring-type overcenter clutches. Table 1 and Figure 1 give dimensions for power take-offs. For dimensions and tolerances of power take-off flanges and flywheels, see SAE J617 and J620, respectively.
Standard

THRUST WASHERS—DESIGN AND APPLICATION
1995-02-01
HISTORICAL
J924_199502
This SAE Standard presents the basic size and tolerance information for the design and manufacture of thrust washers. In most cases, the standard employs nominal figures in both metric and inch-pound units and, therefore, does not necessarily provide exact equivalents.
Standard

FLYWHEELS FOR TWO-PLATE SPRING-LOADED CLUTCHES
1993-12-01
HISTORICAL
J619_199312
This SAE Recommended Practice defines flywheel configuration to promote standardization of flywheels for dry spring-loaded clutches. Clutches to fit flywheels with configurations per this document may not be commercially available. Availability should be ascertained prior to flywheel design Figure 1 and Table 1A.
Standard

APPLICATION GUIDE TO RADIAL LIP SEALS
1991-10-01
HISTORICAL
J946_199110
This SAE Recommended Practice is intended as a guide to the use of radial lip type seals. It has been prepared from existing literature, which includes standards, specifications, and catalog data of both oil seal producers and users and includes generally accepted information and data. The main reason for the preparation of the document is to make standard information available in one document to the users of oil seals.
Standard

APPLICATION GUIDE TO RADIAL LIP SEALS
1989-08-01
HISTORICAL
J946_198908
This recommended practice is intended as a guide to the use of radial lip type seals. It has been prepared from existing literature, which includes standards, specifications, and catalog data of both oil seal producers and users and includes generally-accepted information and data. The main reason for the preparation of the recommended practice is to make standard information available in one document to the users of oil seals.
12Next >Last >>
X