Search Results

A novel method for Single Event Effect (SEE) Radiation Testing using Built-In Self-Test (BIST) feature of indigenously developed Vikram1601 processor is discussed. The novelty is that the usage of BIST avoids need of exhaustive test vectors to ensure test coverage of all the internal registers and physical memory to store them. So processor is the only element vulnerable to radiation damage during testing. The test design was carried out at VSSC, Trivandrum and the testing was carried out at IUAC, Delhi. In the first part, a brief introduction, need and methods of radiation testing of electronics especially SEE of radiation on Silicon based devices, different radiation effects, radiation damage mechanisms and testing methods are described. A brief introduction to Vikram1601 processor, the instruction – TST, used as BIST and testing scheme implementation using TST for studying the SEE is explained.

This SAE Aerospace Recommended Practice (ARP) outlines the basic general design requirements for ground support equipment used in the civil air transport industry. It is intended to assist in standardizing requirements for various configurations of equipment. For procurement of equipment, sections of this document should be specified with due consideration of the functional and environmental requirements of the equipment, and to the relative cost of satisfying those requirements.

This SAE Aerospace Information Report (AIR) lists military and industry specifications, standards, recommended practices, and information reports applicable to aerospace hydraulic and pneumatic systems and components.

The SAE AE-5CH Taskgroup has determined that high flow liquid hydrogen fueling couplings need to be developed in order to fast fill aircraft at the airport. Though the flow rates from a current liquid hydrogen bayonet connect may reach the lower bound flow rates of regional aircraft, there are some shortcomings to this connector for aerospace. For this reason a new specification for flow rates for regional to narrowbody (and potentially later widebody) are to be developed in this documenet. Harmonization for lower flow rates (such as up to 20kg/minute) are planned to be harmonized with ground vehicle fueling such as with ISO 13984. Within this document,coupling descriptions including Flow rates from 84 to 200 kg/minute will be evaluated (and potentially higher), and requirements and testing and safety targets will be specified.

Focused on the permanent magnet synchronous motor (PMSM) used in electric, this paper proposes an online insulation testing method based on voltage injection under high-temperature and high-humidity conditions. The effect of constant humidity and temperature on the insulation performance has been also studied. Firstly, the high-voltage insulation structure and principle of PMSM are analyzed, while an electrical insulation testing method considered constant humidity and temperature is proposed. Finally, a temperature and humidity experimental cycling test is carried out on a certain prototype PMSM, taking heat conduction and radiation models, water vapor, and partial discharge into account. The results show that the electrical insulation performance of the motor under constant humidity and temperature operation environment exhibits a decreasing trend. This study can provide theoretical and practical references for the reliable durability design of PMSM.

Determining occupant kinematics in a vehicle crash is essential when understanding injury mechanisms and assessing restraint performance. Identifying contact marks is key to the process. This study was conducted to assess the ability to photodocument the various fluids on different vehicle interior component types and colors with and without the use of ultraviolet (UV) lights. Biological (blood, saliva, sweat and skin), consumable and chemical fluids were applied to vehicle interior components, such as seatbelt webbing, seat and airbag fabrics, roof liner and leather steering wheel. The samples were photodocumented with natural light and UV light (365 nm) exposure immediately after surface application and again 14 days later. The review of the photos indicated that fabric type and color were important factors. The fluids deposits were better visualized on non-porous than porous materials. For example, blood was better documented on curtain airbags than side or driver airbags.

This document defines cables that are used to provide electrical power for U.S. Department of Defense avionics support and test equipment.

This SAE Aerospace Information Report (AIR) covers forced air technology including: reference material, equipment, safety, operation, and methodology. This resource document is intended to provide information and minimum safety guidelines regarding use of forced air or forced air/fluid equipment to remove frozen contaminants. During the effective period of this document, relevant sections herein should be considered and included in all/any relevant SAE documents.

This SAE Aerospace Recommended Practice (ARP) describes the standards on telemetry data retrieval on ground support equipment (GSE), focusing on wiring requirements, connectors, signal definitions and communication protocols applicable in the industry.

This SAE Aerospace Information Report (AIR) is broken into various categories for convenience and ease of identification. It is the purpose of this document to provide certain criteria for the design and selection of stairways, for the boarding of passengers onto an aircraft. The criteria presented are limited to those factors which affect the safety of the passengers and are coordinated, where applicable, with the practices of the architectural profession, with respect to the design of stairways. Comprehensive design requirements for passenger stairs can be found in the industry documents listed under 2.1.3, 2.1.4, and 2.1.5 hereafter. The recommended practices are applicable to both mobile variable-elevation type stairways and to fixed-elevation stairways of the type built into an aircraft fuselage.

This SAE Aerospace Information Report (AIR) considers the following major areas: 1. major components and their ratings; 2. selection criteria for optimum design balance for electrical systems; 3. effects of operating conditions and environment on both maintenance and life of components; 4. trouble signals - their diagnosis and cure.

This document outlines the functional and design requirements for baggage/cargo tow tractors used for airline services.

The tow vehicle should be designed for towbarless movement of aircraft on the ground. The design will ensure that the unit will safely secure the aircraft nose landing gear within the coupling system for any operational mode.

This SAE aerospace recommended practice (ARP) covers the requirements for external ground power equipment supplying 115/200 V, three-phase, 400 HZ output power measured at the aircraft receptacle. All forms of 400 Hz ground power including mobile and fixed systems are addressed by this document.

The test method describes the procedure for determination of the total acid number (TAN) of new and degraded polyol ester and diester-based gas turbine lubricants by the potentiometric titration technique. The method was validated to cover an acidity range of 0.05 to 6.0 mg KOH g-1. The method may also be suitable for the determination of acidities outside of this range and for other classes of lubricants.

In radiography testing, the radioactive elements Iridium 192 (Ir192) and Cobalt 60 (Co60) are employed to detect subsurface and inner flaws. These radioactive components are kept secure within the radiation-protected source camera. Despite the fact that the camera is safe, there is a little quantity of radiation that may harm human body cells. In this present study, it restricts radiation emission by placing a lead sheet over the source camera, which absorbs the produced radiation. The innovative concept involves in this present work is to place a manually operated switch near the radiation source to emit radiation.

This document provides information and guidance material to assist in assessing the need for and feasibility of developing deicing facilities, the planning (size and location) and design of deicing facilities, and assessing environmental considerations and operational considerations associated with de-icing facilities. The document presents relevant information necessary to define the need for a deicing facility and factors influencing its size, location, and operation. The determination of the need for deicing facilities rests with Airports. Although this document intends to provide information to airport operator and deicing facility planner/designer, all stakeholders, including deicing service providers, should be involved in the development process.

This specification establishes requirements for a corrosion-removing compound in the form of a liquid concentrate.