Refine Your Search

Date

Date

Topic

Topic

Pressure Product development E-25 General Standards for Aerospace and Propulsion Systems On-board energy sources Thermodynamics Heat transfer Design Engineering and Styling

Search Results

Viewing 1 to 20 of 51
123Next >Last >>
Sort by published
Standard

Lubricant, Solid Film
2022-04-01
CURRENT
AS1701F
This document covers the performance requirements for solid dry film lubricants, air dried or heat cured, for use in aerospace applications. These lubricants are intended to prevent galling, and may be capable of remaining effective for extended periods of time after exposure to extreme environmental conditions.
Standard

Thread Inspection Practices
2020-02-03
CURRENT
AS5870
This document addresses AS8879 thread inspection issues relating to selection, usage and capability of gages. It addresses the selection of calibrated measurement gages, the need for defined quality metrics, the methodology of determining the appropriate guardband factors, and the minimum inspection requirements for single element pitch diameter gages. Users of this document shall apply the information described herein for the evaluation of the capability of their measurements based on the measurement consumer risk. It involves the analysis of the measurement (product) distribution and biases of both the product and measurement system distributions. It protects the consumer from the worst case distribution results. A whitepaper has been developed to provide supporting documentation and the rationale used in the development of this standard. This whitepaper will be published by the SAE as an Aerospace Information Report (AIR6553).
Standard

Groove Design - Metal Face Seal
2019-06-06
CURRENT
AIR1108A
Groove designs presented herein are applicable for use with machined or formed metal seals which are similar in configuration to those shown in figure 3, which operate under internal pressure or in vacuum service and which have been specifically qualified or recommended by the purchaser or the manufacturer for use with this AIR. They are also applicable for use with metal o-rings (e.g., MS9142, MS202 thru MS9205) where interchangeability with machined or formed metal seals is desired. For metal o-ring groove designs where inter-changeability is not a requirement refer to ARP 674.
Standard

Modules and Basic Racks of Metric Spur and Helical Gears
2018-09-11
CURRENT
AS1560B
This SAE Aerospace Standard (AS) establishes the standard modules for aerospace metric involute gear teeth and establishes the tooth dimensions of aerospace metric involute gear teeth in terms of the conjugate rack type cutter whose counterpart reference profile is called the basic rack profile of the generated gear, having the tooth dimensions expressed in terms proportional to the module.
Standard

White Paper to Support Supersession of MIL-S-8879C With AS8879C
2018-08-23
HISTORICAL
AIR5926
This paper was prepared to support supersession of MIL-S-8879C with Screw Thread Conformity Task Force selected industry standard AS8879C, published by the Society of Automotive Engineers (SAE). Other documentation changes will be covered by separate papers. Separate papers are anticipated for thread gaging issues, and thread gage calibration procedures. The STC-TF decided that the thread design standard needed to be completed before thread gage definition could be addressed. Thread gage definition has to be known before calibration procedures can be addressed.
Standard

Groove Design, Metal O-Ring Gasket
2018-03-30
CURRENT
ARP674D
Groove designs presented herein are applicable for use with the following "MS" metal O-ring gaskets conforming to the applicable "AS" standard drawings listed in 1(a) or 1(b), or to dimensionally equivalent gaskets of other materials: a AMS 5570 or AMS 5576 Plain 1 AS9141 - 0.035 tube × 0.006 wall 2 AS9142 - 0.062 tube × 0.006 wall 3 AS9202 - 0.062 tube × 0.010 wall 4 AS9203 - 0.094 tube × 0.006 wall 5 AS9204 - 0.094 tube × 0.010 wall 6 AS9205 - 0.125 tube × 0.010 wall b AMS 5570 or AMS 5576 Silver Plated 1 AS9371 - 0.035 tube × 0.006 wall 2 AS9372 - 0.062 tube × 0.006 wall 3 AS9373 - 0.062 tube × 0.010 wall 4 AS9374 - 0.094 tube × 0.006 wall 5 AS9375 - 0.094 tube × 0.010 wall 6 AS9376 - 0.125 tube × 0.010 wall NOTE: The term "AS gasket" as used in this document refers to the 'MS' part numbers defined on the applicable 'AS' standards listed in 1(a) or 1(b).
Standard

Lubricant, Solid Film
2014-12-28
HISTORICAL
AS1701E
This document covers the performance requirements for solid dry film lubricants, air dried, or heat cured for use in aerospace applications. These lubricants are intended to prevent galling, and may be capable of remaining effective for extended periods of time after exposure to extreme environmental conditions.
Standard

Lubricant, Solid Film
2014-01-09
HISTORICAL
AS1701D
Delete AS7108, clarify thickness requirements for coating of threads, clarify tape test requirements, update references, and general revision.
123Next >Last >>
X