Search Results

A damper and a gas spring being a thermo engine which vibrational energy absorption occurs over heat transformation, requires very specific properties of thermo chemical stability from the hydraulic fluid as well as shear strength by heat and pressure effect. It competes to the hydraulic fluid the task of this transformation vehicle. The absorption performance of a damper depends on variation of physical-chemical properties of the hydraulic fluid under heat effect and the maintenance of this performance depends on conservation of those properties during time. The traditional hydraulic fluids for this application, despite its thermo-chemical stability, suffer a deterioration process of those properties under severe operating conditions and consequently reflect in the damper component lifetime.

With the current use of bio-renewable fuel, the application of Ethanol in Flex-Fuel vehicles presents a very low CO2 emission alternative when the complete cycle, from plantation, fuel production, till vehicle use, is considered. In Brazil more than 80% of the car production is composed of Flex-Fuel vehicles. Due to the lower heating content of the Ethanol, more aggressive combustion calibrations are used to obtain the same engine power than when burning gasoline. Such Ethanol demands, associated with the continuous increase of engine specific power has lead to thermo-mechanical loads which challenges the tribology of piston rings. The ethanol use brings also some specific tribological differences not very well understood like fuel dilution in the lube oil, especially on cold start, corrosive environment etc. Under specific driving conditions, incipient failures like spalling on nitrided steel top rings have been observed.

One of the problems related to the gray cast iron cylinder liner, and others materials, transportation is the possibility of the surface corrosion due to a non-controlled environment. The manufacturer has the responsability to guarantee the product free of corrosion up to the opening at final destination. Aiming to evaluate the liners transportation, regarding the corrosion potential during the transportation cycle, Magneti Marelli Cofap did experiments where the atmospheric conditions inside the pallets were measured. Using a special device it was possible to check the temperature, absolute humidity and relative humidity variations at every step, which were pre-set by using an specific software. The main reason for variations that might happen at the liner surface are related to transportation and storage. The corrosion rate will be determined by physical and chemical atmospheric conditions.

The components of the piston/ring/liner system must have their wear resistance increased to meet the new engine requirements. The engine operating conditions can be even worse if corrosive wear in the engine is expected to occur. This paper presents a study to improve the wear resistance of piston ring coatings and liner materials by the addition of chromium carbide and carbide forming alloying elements, respectively. The engine tests were run with high sulfur fuel (about 1.0 wt%) and lubricant with low total base number (TBN) with the objective of increasing the corrosive conditions. The results show the improvement of the ring coatings wear resistance with the increase of the chromium carbide content. The cylinder liner materials also presented lower wear rates when they had hard particles, mainly due to the addition of niobium, vanadium and titanium.

The evolution of internal combustion engines has led to friction reduction as well as to gaseous emissions reduction, demanding the use of narrower rings. Nodular cast iron is used satisfactorily for compression piston rings, with wear resistant coatings to improve their durability. However, for more severe applications and rings narrower than 1.2mm, even the nodular cast iron mechanical resistance is not enough. In this way, the use of steel is recommended, which may have its tribological properties improved by the nitriding thermochemical treatment. This paper presents the characteristics of the materials and of the nitriding process of compression and oil control rings as well as bench and dynamometric test results run during the development of these products.

The first groove piston rings are highly loaded due to the combustion chamber nearness. They support high pressure against the cylinder wall, high working temperature and low lubricant level. In critical working condition, it could be used flame sprayed molybdenum coating the rings from 99.9% purity wires. The wire flame spray process limitation is the deposition of only one material. Here it is presented a new concept for getting wear resistant coatings on first groove piston rings, by flame spraying, by applying simultaneously materials with different characteristics from wires. Comparative results between the proposal (Moly + Inox) and the conventional (Moly) coating are presented. The simultaneous application of stainless steel and molybdenum decreases the first groove piston rings wear without loss of scuffing resistance.

The higher load in heavy duty Diesel engines and the use of piston ring coatings with higher wear resistance cause more severe working conditions to the cylinder liners. In some cases, high localized wear occurs at the top dead center (TDC) of the first groove ring, where the loads and lubrication conditions are critical. It was studied the effect of the addition of hard particles on cylinder liner materials. The presence of these particles was obtained through the use of small quantities of strong carbide forming alloying elements: Vanadium, Niobium and Titanium. Cylinder liners with hard particle addition were tested in comparison to regular liners. This test used high sulfur fuel (> 1.0 wt %) and low additivation lubricant oil, maintaining the same ring pack configuration for both liners. The results showed sensible liner wear reduction at the TDC of the first ring without compromising the ring pack performance.