Search Results

Standard

Multiposition Small Engine Exhaust System Fire Ignition Suppression

2020-10-06

CURRENT

J335_202010

This SAE Recommended Practice establishes equipment and test procedures for determining the performance of spark arrester exhaust systems of multiposition small engines (<19 kW) used in portable applications, including hand-held, hand-guided, and backpack mounted devices. It is not applicable to spark arresters used in vehicles or stationary equipment.

Standard

Spark Arrester Test Procedure for Large Size Engines

2013-03-26

HISTORICAL

J342_201303

This SAE Recommended Practice establishes equipment and procedures for the evaluation of the effectiveness and other performance characteristics of spark arresters or turbochargers used on the exhaust system of large engines normally used in a railroad locomotive, stationary power plant, and other similar applications. This document does not cover applications requiring flame arresting, exhaust gas cooling, or isolation from explosive gases. Two test methods are presented: a laboratory test using ambient air (cold test) and an engine test using exhaust gases (hot test). The hot test is preferred. Arresters tested by the provisions of this document can be expected to perform as tested when tilted no more than 45 degrees from their normal position. Test results from a spark arrester or turbocharger evaluated by the hot test can be applied to different engines of similar design, provided the data shows it to be effective in the applicable flow ranges.

Standard

Engine Flywheel Housings with Sealed Flanges

2012-10-23

CURRENT

J1172_201210

This SAE Recommended Practice defines flywheel housing flange configurations for applications requiring "O" ring sealing of the flange pilot bore. Table 1 and Figure 1 show dimensions that are different from those in SAE J617. All other dimensions and tolerances of SAE J617 apply.

Standard

Industrial Power Take-Offs With Driving Ring-Type Overcenter Clutches

2012-10-23

CURRENT

J621_201210

This SAE Standard defines installation dimensions of industrial power take-offs with driving ring-type overcenter clutches. Table 1 and Figure 1 give dimensions for power take-offs. For dimensions and tolerances of power take-off flanges and flywheels, see SAE J617 and J620, respectively.

Standard

Multiposition Small Engine Exhaust System Fire Ignition Suppression

2012-10-23

HISTORICAL

J335_201210

This SAE Recommended Practice establishes equipment and test procedures for determining the performance of spark arrester exhaust systems of multiposition small engines (<19 kW) used in portable applications, including hand-held, hand-guided, and backpack mounted devices. It is not applicable to spark arresters used in vehicles or stationary equipment.

Standard

Housing Internal Dimensions for Single- and Two-Plate Spring-Loaded Clutches

2012-05-31

CURRENT

J373_201205

This SAE Recommended Practice defines the minimum internal dimensions for clutch housings to provide adequate clearance for single- and two-plate spring-loaded clutches. (See Figure 1.) Consult SAE J617 for housing flange dimensions. Consult SAE J618 and J619 for spring-loaded clutch flywheel dimensions F and G and other dimensional data. Table 1 provides housing minimum internal dimensions for single- and two-plate spring-loaded clutches.

Standard

Flywheels for Two-Plate Spring-Loaded Clutches

2012-05-31

CURRENT

J619_201205

This SAE Recommended Practice defines flywheel configuration to promote standardization of flywheels for dry spring-loaded clutches. Clutches to fit flywheels with configurations per this document may not be commercially available. Availability should be ascertained prior to flywheel design Figure 1 and Table 1A.

Standard

Thrust Washers – Design and Application

2011-06-13

CURRENT

J924_201106

This SAE Standard presents the basic size and tolerance information for the design and manufacture of thrust washers. In most cases, the standard employs nominal figures in both metric and inch-pound units and, therefore, does not necessarily provide exact equivalents.

Standard

Engine and Transmission Dipstick Marking

2011-06-13

CURRENT

J614_201106

This SAE Recommended Practice provides information useful in the marking of engine and transmission dipsticks used for fluid level indication.

Standard

Design Guide for Formed-in-Place Gaskets

2008-07-08

CURRENT

J1497_200807

This SAE Recommended Practice presents information which is intended as a guide for proper designing, selection, application, and servicing of liquid, formed-in-place gasket (FIPG) materials.

Standard

Rubber Rings for Automotive Applications

2002-10-25

CURRENT

J120_200210

This SAE Recommended Practice covers the dimensional and material requirements of rubber O-rings for automotive application and rectangular section rubber seal rings for automotive applications.

Standard

Static and Reciprocating Elastomeric Transmission Seals

2002-10-25

CURRENT

J654_200210

This SAE Recommended Practice is intended as a guide to the design and use of static and reciprocating elastomeric transmission seals. It has been prepared from existing literature, which includes standards, specifications, and catalog data of both producers and users and includes generally-accepted information and data. The main reason for the preparation of the document is to make standard information available in one document to the users of static and reciprocating elastomeric transmission seals.

Standard

Diesel Catalytic Converter Nomenclature and Terminology

2001-10-30

CURRENT

J1643_200110

This SAE Draft Technical Report applies to nomenclature of diesel engine catalytic converter parts and various configurations.

Standard

ENGINE AND TRANSMISSION DIPSTICK MARKING

1995-06-29

HISTORICAL

J614_199506

This SAE Recommended Practice provides information useful in the marking of engine and transmission dipsticks used for fluid level indication.

Standard

INDUSTRIAL POWER TAKE-OFFS WITH DRIVING RING-TYPE OVERCENTER CLUTCHES

1995-03-08

HISTORICAL

J621_199503

This SAE Standard defines installation dimensions of industrial power take-offs with driving ring-type overcenter clutches. Table 1 and Figure 1 give dimensions for power take-offs. For dimensions and tolerances of power take-off flanges and flywheels, see SAE J617 and J620, respectively.

Standard

DIESEL ENGINE SMOKE MEASUREMENT

1995-02-24

HISTORICAL

J255_199502

Measurement of diesel smoke in an accurate and consistent manner has been a serious problem for engine and vehicle manufacturers, users, and agencies charged with enforcing smoke limits. Several instruments, based on different principles and using different scales, are commonly used. In addition to these, human observation and judgment are often used to relate smoke to a variety of standards. The purpose of this SAE Information Report is to provide an understanding of the nature of diesel smoke, how it can be measured, and how the various measurement methods can be correlated. Except for defining the various types of smoke, the report deals solely with the steady-state measurement of visible, black smoke emitted from diesel engines. For the benefit of those who wish to study various aspects of the subject in greater depth, a list of useful references is included in Section 2. This document is divided into the following sections:

Standard

THRUST WASHERS—DESIGN AND APPLICATION

1995-02-01

HISTORICAL

J924_199502

This SAE Standard presents the basic size and tolerance information for the design and manufacture of thrust washers. In most cases, the standard employs nominal figures in both metric and inch-pound units and, therefore, does not necessarily provide exact equivalents.

Standard

FLYWHEELS FOR TWO-PLATE SPRING-LOADED CLUTCHES

1993-12-01

HISTORICAL

J619_199312

This SAE Recommended Practice defines flywheel configuration to promote standardization of flywheels for dry spring-loaded clutches. Clutches to fit flywheels with configurations per this document may not be commercially available. Availability should be ascertained prior to flywheel design Figure 1 and Table 1A.

Standard

PROCEDURE FOR MEASURING BORE AND FACE RUNOUT OF FLYWHEELS, FLYWHEEL HOUSINGS, AND FLYWHEEL HOUSING ADAPTERS

1993-04-01

HISTORICAL

J1033_199304

This SAE Recommended Practice applies to any internal combustion engine which can utilize SAE No. 6 thru SAE No. 00 size flywheel housing. It provides instructions for correcting flywheel housing bore runout readings which are influenced by crankshaft bearing clearance. Limits for bore and face runout are specified in the various SAE Standards and Recommended Practices covering flywheels and flywheel housings.

Standard

APPLICATION GUIDE TO RADIAL LIP SEALS

1991-10-01

HISTORICAL

J946_199110

This SAE Recommended Practice is intended as a guide to the use of radial lip type seals. It has been prepared from existing literature, which includes standards, specifications, and catalog data of both oil seal producers and users and includes generally accepted information and data. The main reason for the preparation of the document is to make standard information available in one document to the users of oil seals.