Search Results

Standard

Multiposition Small Engine Exhaust System Fire Ignition Suppression

2020-10-06

CURRENT

J335_202010

This SAE Recommended Practice establishes equipment and test procedures for determining the performance of spark arrester exhaust systems of multiposition small engines (<19 kW) used in portable applications, including hand-held, hand-guided, and backpack mounted devices. It is not applicable to spark arresters used in vehicles or stationary equipment.

Standard

Spark Arrester Test Carbon

2020-10-06

CURRENT

J997_202010

This SAE Standard establishes physical properties required of SAE Coarse Test Carbon and SAE Fine Test Carbon and establishes test methods to ensure that these requirements are met.

Standard

Spark Arrester Test Procedure for Large Size Engines

2013-03-26

HISTORICAL

J342_201303

This SAE Recommended Practice establishes equipment and procedures for the evaluation of the effectiveness and other performance characteristics of spark arresters or turbochargers used on the exhaust system of large engines normally used in a railroad locomotive, stationary power plant, and other similar applications. This document does not cover applications requiring flame arresting, exhaust gas cooling, or isolation from explosive gases. Two test methods are presented: a laboratory test using ambient air (cold test) and an engine test using exhaust gases (hot test). The hot test is preferred. Arresters tested by the provisions of this document can be expected to perform as tested when tilted no more than 45 degrees from their normal position. Test results from a spark arrester or turbocharger evaluated by the hot test can be applied to different engines of similar design, provided the data shows it to be effective in the applicable flow ranges.

Standard

Maximum Allowable Rotational Speed for Internal Combustion Engine Flywheels

2012-10-23

CURRENT

J1456_201210

This SAE Recommended Practice applies to flywheels and flywheel-starter ring gear assemblies used with internal combustion engines of the spark ignition and diesel type equipped with a governor or speed limiting device. Engine sizes are those capable of using SAE No. 6 through SAE No. 00 flywheel housings. This document applies to methods used to determine the rotational speed capability of flywheels for stresses imposed by centrifugal forces only.

Standard

Multiposition Small Engine Exhaust System Fire Ignition Suppression

2012-10-23

HISTORICAL

J335_201210

This SAE Recommended Practice establishes equipment and test procedures for determining the performance of spark arrester exhaust systems of multiposition small engines (<19 kW) used in portable applications, including hand-held, hand-guided, and backpack mounted devices. It is not applicable to spark arresters used in vehicles or stationary equipment.

Standard

Thrust Washers – Design and Application

2011-06-13

CURRENT

J924_201106

This SAE Standard presents the basic size and tolerance information for the design and manufacture of thrust washers. In most cases, the standard employs nominal figures in both metric and inch-pound units and, therefore, does not necessarily provide exact equivalents.

Standard

Guide to the Application and Use of Engine Coolant Pump Face Seals

2000-11-07

HISTORICAL

J1245_200011

This SAE Recommended Practice is intended as a guide in the usage of mechanical face seals for the engine coolant pump application. The main purpose of the document is to fill the void caused by the lack of a ready source of practical information on the design and use of the engine coolant pump face seal. Included in the document is a compilation of present practices, as in a description of the various types of seals, material combinations, design data, tolerances, drawing format, qualification and inspection information, and quality control data. The terminology used throughout the document is recommended and, through common usage, is hoped to promote uniformity in seal nomenclature.

Standard

Seals—Bond Test Fixture and Procedure

2000-10-09

HISTORICAL

J1900_200010

Bond, as it relates to elastomeric seals, is defined as “The adhesion, established by vulcanization, between two cured elastomeric surfaces, or between one cured elastomeric surface and one nonelastomeric surface.”1 Vulcanization refers in this case to chemical bonding. Good bond is essential to the function of elastomeric radial lip seals and other precision bonded parts. This SAE Recommended Practice describes a universal bond test fixture developed by the RMA that can be mounted to a conventional tensile test machine. This will allow a quantitative evaluation of bond rather than a merely qualitative one.

Standard

SEALS—TERMINOLOGY OF RADIAL LIP

1997-05-01

HISTORICAL

J111_199705

The purpose of this SAE Recommended Practice is to provide a glossary of radial seal terms and nomenclature which are normally encountered in the design, manufacture, installation, testing, inspection, and failure mode analysis of radial seals. The information will aid in the understanding and communication among those people associated with radial seals.

Standard

MAXIMUM ALLOWABLE ROTATIONAL SPEED FOR INTERNAL COMBUSTION ENGINE FLYWHEELS

1995-07-03

HISTORICAL

J1456_199507

This SAE Recommended Practice applies to flywheels and flywheel-starter ring gear assemblies used with internal combustion engines of the spark ignition and diesel type equipped with a governor or speed limiting device. Engine sizes are those capable of using SAE No. 6 through SAE No. 00 flywheel housings. This document applies to methods used to determine the rotational speed capability of flywheels for stresses imposed by centrifugal forces only.

Standard

RUBBER RINGS FOR AUTOMOTIVE APPLICATIONS

1995-06-29

HISTORICAL

J120_199506

This SAE Recommended Practice covers the dimensional and material requirements of rubber O-rings for automotive application and rectangular section rubber seal rings for automotive applications.

Standard

STANDARD CLASSIFICATION SYSTEM FOR NONMETALLIC AUTOMOTIVE GASKET MATERIALS

1995-03-25

HISTORICAL

J90_199503

The classification system provides a means for specifying or describing pertinent properties of commercial nonmetallic gasket materials. Materials composed of asbestos, cork, cellulose, and other organic or inorganic materials in combination with various binders or impregnants are included. Materials normally classified as rubber compounds are not included, since they are covered in SAE J200—ASTM D 2000. Gasket coatings are not covered, since details thereof are intended to be given on engineering drawings or in separate specifications.

Standard

THRUST WASHERS—DESIGN AND APPLICATION

1995-02-01

HISTORICAL

J924_199502

This SAE Standard presents the basic size and tolerance information for the design and manufacture of thrust washers. In most cases, the standard employs nominal figures in both metric and inch-pound units and, therefore, does not necessarily provide exact equivalents.

Standard

DESIGN GUIDE FOR FORMED-IN-PLACE GASKETS

1994-04-05

HISTORICAL

J1497_199404

This SAE Recommended Practice presents information which is intended as a guide for proper designing, selection, application, and servicing of liquid, formed-in-place gasket (FIPG) materials.

Standard

SEALS - BOND TEST FIXTURE AND PROCEDURE

1990-10-01

HISTORICAL

J1900_199010

Bond, as it relates to elastomeric seals, is defined as "The adhesion, established by vulcanization, between two cured elastomeric surfaces, or between one cured elastomeric surface and one nonelastomeric surface".1 Vulcanization refers in this case to chemical bonding. Good bond is essential to the function of elastomeric radial lip seals and other precision. bonded parts. This SAE Recommended Practice describes a universal bond test fixture developed by the RMA that can be mounted to a conventional tensile test machine. This will allow a quantitative evaluation of bond rather than a merely qualitative one.

Standard

MAXIMUM ALLOWABLE ROTATIONAL SPEED FOR INTERNAL COMBUSTION ENGINE FLYWHEELS

1990-06-01

HISTORICAL

J1456_199006

This SAE Recommended Practice applies to flywheels and flywheel-starter ring gear assemblies used with internal combustion engines of the spark ignition and diesel type equipped with a governor or speed limiting device. Engine sizes are those capable of using SAE No. 6 through SAE No. 00 flywheel housings. This document applies to methods used to determine the rotational speed capability of flywheels for stresses imposed by centrifugal forces only.

Standard

STANDARD CLASSIFICATION SYSTEM FOR NONMETALLIC AUTOMOTIVE GASKET MATERIALS

1990-06-01

HISTORICAL

J90_199006

The classification system provides a means for specifying or describing pertinent properties of commercial nonmetallic gasket materials. Materials composed of asbestos, cork cellulose, and other organic or inorganic materials in combination with various binders or impregnants are included. Materials normally classified as rubber compounds are not included, since they are covered in SAE J200 - ASTM D 2000. Gasket coatings are not covered, since details thereof are intended to be given on engineering drawings or in separate specifications.

Standard

GUIDE TO THE APPLICATION AND USE OF PASSENGER CAR AIR-CONDITIONING COMPRESSOR FACE SEALS

1990-05-01

HISTORICAL

J1954_199005

This SAE Recommended Practice is intended as a guide in the usage of mechanical face seals for the passenger car air-conditioning compressor application. Included in this guide is a compilation of present practices; for example, a description of various type seals, material combinations, design data, tolerances, drawing format, qualification testing, inspection information and quality control data. The terminology used is recommended to promote uniformity in seal nomenclature.

Standard

DESIGN GUIDE FOR FORMED-IN-PLACE GASKETS

1988-12-01

HISTORICAL

J1497_198812

This manual presents information which is intended as a guide for proper designing, selection, application, and servicing of liquid, formed-in-place gasket (FIPG) materials.

Standard

DESIGN GUIDE FOR FORMED-IN-PLACE GASKETS

1988-05-01

HISTORICAL

J1497_198805

This manual presents information which is intended as a guide for proper designing, selection, application, and servicing of liquid, formed-in-place gasket (FIPG) materials.