Refine Your Search

Date

Date

Topic

Topic

Wheels Brake torque Electrical, Electronics, and Avionics Electrical systems MTC1, Earthmoving Machinery

Search Results

Viewing 1 to 20 of 27
12Next >Last >>
Sort by published
Standard

Cutting Edge - Double Bevel Cross Sections
2020-01-15
CURRENT
J738_202001
This standard is for cutting edge sections typically used in earth-moving machinery defined in SAE J1116 and ISO 6165: a Scrapers as defined in ISO 7133. b Dozers as described in ISO 6747. c Loaders as described in ISO 7131. d Graders as described in ISO 7134. Hole spacing is defined ISO 7129. Hole conformation is defined in SAE J740.
Standard

Hydraulic Excavator Operator Controls
2019-06-06
CURRENT
J1177_201906
This standard covers mobile hydraulic excavator controls and the specific arrangement and direction of motion for the primary controls. This standard applies to mobile hydraulic excavators as described in ISO 7135—Earthmoving machinery—Hydraulic excavators—Terminology and commercial specifications, and ISO 6165—Earthmoving machinery—Basic types—Vocabulary.
Standard

Specification Definitions - Hydraulic Backhoes
2012-07-16
HISTORICAL
J49_201207
This standard applies to hydraulic backhoes which have no more than 190 degrees of rotational swing, and are mounted on wheel tractors and crawler tractors.
Standard

Loading Ability Test Procedure - Scrapers
2011-10-27
CURRENT
J764_201110
This SAE Information Report applies to all independent or combination construction and industrial machines that are designed to scraper-load and transport material. (See SAE J1116 and J1057a.)
Standard

Rated Operating Load for Loaders
2007-04-30
HISTORICAL
J818_200704
This SAE Standard applies to wheel and crawler loaders taking only hydraulic lift capacity and tipping capacity into consideration. It is recognized that specific operating conditions may allow larger, or require smaller loads than the rated operating load. Some conditions could require more careful or restricted operation with the rated operating load. This standard is not to be construed as setting up test procedures or conditions.
Standard

Rated Operating Load for Loaders Equipped with Log or Material Forks without Vertical Mast
2002-10-31
HISTORICAL
J1197_200210
This SAE Recommended Practice applies to wheel and crawler loaders when equipped with log or material handling forks without vertical masts, taking only hydraulic lift capacity and operating stability into consideration. It is recognized that specific operating conditions may allow larger, or require smaller loads than the rated operating load. Some conditions would require more careful or restricted operation with the rated operating load. This practice is not to be construed as setting up test procedures or conditions.
Standard

CAPACITY RATING—ELEVATING SCRAPERS
1993-06-01
HISTORICAL
J957_199306
This SAE Standard specifies a procedure for approximating the volume of a typical material carried in the bowl of an elevating scraper as defined in SAE J728 and SAE J1057. The volumes are based on the inside dimensions of the bowl and a representative volume on top of the bowl. This rating method is intended to provide a consistent means of comparing capacities; it is not intended to define actual capacities that might be observed in any specific application.
Standard

CAPACITY RATING—SCRAPER, OPEN BOWL
1993-06-01
HISTORICAL
J741_199306
This SAE Standard specifies a procedure for approximating the volume of typical materials contained in the bowl of Open Bowl scrapers as defined in SAE J728 and SAE J1057. The volumes are based on the inside dimensions of the bowl and representative volumes on top of the bowl. This rating method is intended to provide a consistent means of comparing capacities; it is not intended to define actual capacities that might be observed in any specific application.
Standard

CUTTING EDGE—CURVED GRADER
1991-06-01
HISTORICAL
J739_199106
This SAE Standard is intended for curved cutting edge sections used on graders as defined in SAE J870 and J1057. (See Figure 1 and Table 1.) Hole conformation is further defined in SAE J740 and J1580.
Standard

RATED OPERATING LOAD FOR LOADERS EQUIPPED WITH LOG OR MATERIAL FORKS WITHOUT VERTICAL MAST
1991-02-01
HISTORICAL
J1197_199102
This SAE Recommended Practice applies to wheel and crawler loaders when equipped with log or material handling forks without vertical masts, taking only hydraulic lift capacity and operating stability into consideration. It is recognized that specific operating conditions may allow larger, or require smaller loads than the rated operating load. Some conditions would require more careful or restricted operation with the rated operating load. This practice is not to be construed as setting up test procedures or conditions.
Standard

COMPONENT NOMENCLATURE—GRADERS
1990-07-30
HISTORICAL
J870_199007
This SAE Standard provides names of major components peculiar to graders as defined in SAE J1057 (See Figure 1). Illustrations of components are not intended to be exactly descriptive of any particular machine.
Standard

COMPONENT NOMENCLATURE—SCRAPERS
1990-07-01
HISTORICAL
J728_199007
This SAE Standard provides names of major components peculiar to the scraper portion of tractor-scrapers. Reference SAE J1057. Illustrations of components are not intended to be exactly descriptive of any particular machine.
Standard

HOLE SPACING FOR SCRAPER AND DOZER CUTTING EDGES
1989-08-01
HISTORICAL
J737_198908
This standard is intended for cutting edge sections used on: a Tractor-scrapers as described in SAE J1057 and J728. b Dozers as described in SAE J729. These cutting edges are further defined in SAE J738 for cross section and SAE J740 and J1580 for hole conformation.
Standard

CAPACITY RATING—DOZER BLADES
1988-03-01
HISTORICAL
J1265_198803
This standard applies only to straight, angling, semi-U, and U-blades for crawler and wheel tractors. It applies to angling blades only in the straight (not angled) position.
Standard

RATED OPERATING LOAD FOR LOADERS
1987-05-01
HISTORICAL
J818_198705
This SAE Standard applies to wheel and crawler loaders taking only hydraulic lift capacity and tipping capacity into consideration. It is recognized that specific operating conditions may allow larger, or require smaller loads than the rated operating load. Some conditions could require more careful or restricted operation with the rated operating load. This standard is not to be construed as setting up test procedures or conditions.
Standard

NOMENCLATURE—ROLLERS AND COMPACTORS
1986-01-01
HISTORICAL
J1017_198601
This SAE Standard provides names of major components peculiar to rollers and compactors. Illustrations of components are not intended to be exactly descriptive of any particular machine. See Figures 1 to 3.)
Standard

CAPACITY RATING—LOADER BUCKET
1985-02-01
HISTORICAL
J742_198502
This standard applies to buckets of loaders (as defined by SAE J1057a, Identification Terminology of Earthmoving machines).
12Next >Last >>
X