Search Results

Rapid adoption of battery electric vehicles means improving the energy consumption and energy efficiency of these new vehicles is a top priority. One method of accomplishing this is regenerative braking, which converts kinetic energy to electrical energy stored in the battery pack while the vehicle is decelerating. Coasting is an alternative strategy that minimizes energy consumption by decelerating the vehicle using only road load. A battery electric vehicle model is refined to assess regenerative braking, coasting, and other deceleration strategies. A road load model based on public test data calculates tractive effort requirements based on speed and acceleration. Bidirectional Willans lines are the basis of a powertrain model simulating battery energy consumption. Vehicle tractive and powertrain power are modeled backward from prescribed linear velocity curves, and the coasting trajectory is forward modeled given zero tractive power.

The influence of driver modeling and drive cycle target speed trace modification on vehicle dynamics within energy consumption simulations is studied. EPA dynamometer speed error criteria and the SAE J2951 Drive Quality Evaluation for Chassis Dynamometer Testing standard are applied to simulation outputs as proposed components of simulation validation, providing guidelines for acceptable vehicle speed outputs and allowing comparison of simulation results to reported EPA dynamometer test statistics. The combined effect of driver model tuning and drive cycle interpolation methods is investigated for the UDDS, HwFET and US06 drive cycles, with EPA-specified linearly interpolated speed trace and a PI controller driver as a baseline result.

A new and unique electric vehicle powertrain model based on bidirectional power flow for propel and regenerative brake power capture is developed and applied to production battery electric vehicles. The model is based on a Willans line model to relate power input from the battery and power output to tractive effort, with one set of parameters (marginal efficiency and an offset loss) for the bidirectional power flow through the powertrain. An electric accessory load is included for the propel, brake and idle phases of vehicle operation. In addition, regenerative brake energy capture is limited with a regen fraction (where the balance goes to friction braking), a power limit, and a low-speed cutoff limit. The purpose of the model is to predict energy consumption and range using only tractive effort based on EPA published road load and test mass (test car list data) and vehicle powertrain parameters derived from EPA reported unadjusted UDDS and HWFET energy consumption.

The Hybrid Electric Vehicle Team of Virginia Tech (HEVT) is currently modeling and bench testing powertrain components for a parallel plug-in hybrid electric vehicle (PHEV). The custom powertrain is being implemented in a 2016 Chevrolet Camaro for the EcoCAR 3 competition. The engine, a General Motors (GM) L83 5.3L V8 with Active Fuel Management (AFM) from a 2014 Silverado, is of particular importance for vehicle integration and functionality. The engine is one of two torque producing components in the powertrain. AFM allows the engine to deactivate four of the eight cylinders which is essential to meet competition goals to reduce petroleum energy use and greenhouse gas emissions. In-vehicle testing is performed with a 2014 Silverado on a closed course to understand the criteria to activate AFM. Parameters required for AFM activation are monitored by recording vehicle CAN bus traffic.

The Hybrid Electric Vehicle Team of Virginia Tech (HEVT) is currently developing a control strategy for a parallel plug-in hybrid electric vehicle (PHEV). The hybrid powertrain is being implemented in a 2016 Chevrolet Camaro for the EcoCAR 3 competition. Fuzzy rule sets determine the torque split between the motor and the engine using the accelerator pedal position, vehicle speed and state of charge (SOC) as the input variables. The torque producing components are a 280 kW V8 L83 engine with active fuel management (AFM) and a post-transmission (P3) 100 kW custom motor. The vehicle operates in charge depleting (CD) and charge sustaining (CS) modes. In CD mode, the model drives as an electric vehicle (EV) and depletes the battery pack till a lower state of charge threshold is reached. Then CS operation begins, and driver demand is supplied by the engine operating in V8 or AFM modes with supplemental or loading torque from the P3 motor.

The Hybrid Electric Vehicle Team (HEVT) of Virginia Tech is currently going through several modeling and testing stages to develop models that represent the P3 PHEV powertrain the team is building as part the EcoCAR 3 competition. The model development process consists of several major steps. First, Model-in-the-Loop (MIL) testing is conducted to validate a conventional vehicle model, down-select a desired powertrain configuration, and generate initial vehicle technical specifications. HEVT is pursuing a performance powertrain that balances high performance with minimal energy consumption. Initial MIL modeling results yield an IVM-60 mph time of 4.9 seconds and an overall UF-weighted 4-cycle energy consumption of 560 Wh/km. MIL modeling provides an initial reference to compare subsequent vehicle modeling. Following the MIL process, Software-in-the-Loop (SIL) is used to develop a vehicle model from the ground-up that facilitates the transition to Hardware-in-the-Loop (HIL) testing.

The Wayne State University student team reengineered a mid-sized sedan into a functional plug-in hybrid electric vehicle as participants in the EcoCAR 2 competition sponsored by the US Department of Energy and managed by Argonne National Laboratory. The competition goals included reducing petroleum usage, emissions, and energy consumption through implementing advanced vehicle technologies. During the competition, the team did plug-in charging of the 19 kWh high voltage traction battery, drove in pure electric mode (engine off) until the battery was depleted, then switched to hybrid mode and continued driving by using E85 from the fuel tank. The pure electric mode vehicle driving range was 48 km [30 miles] while pulling an emissions instrumented test trailer and projected to be 58 km [36 miles] without the test trailer load for the competition's city/highway blend drive cycle.

It is well known that thermal management is a key factor in design and performance analysis of Lithium-ion (Li-ion) battery, which is widely adopted for hybrid and electric vehicles. In this paper, an air cooled battery thermal management system design has been proposed and analyzed for mild hybrid vehicle application. Computational Fluid Dynamics (CFD) analysis was performed using CD-adapco's STAR-CCM+ solver and Battery Simulation Module (BMS) application to predict the temperature distribution within a module comprised of twelve 40Ah Superior Lithium Polymer Battery (SLPB) cells connected in series. The cells are cooled by air through aluminum cooling plate sandwiched in-between every pair of cells. The cooling plate has extended the cooling surface area exposed to cooling air flow. Cell level electrical and thermal simulation results were validated against experimental measurements.

The Hybrid Electric Vehicle Team of Virginia Tech (HEVT) is participating in the 2012-2014 EcoCAR 2: Plugging in to the Future Advanced Vehicle Technology Competition series organized by Argonne National Lab (ANL), and sponsored by General Motors Corporation (GM) and the U.S. Department of Energy (DOE). The goals of the competition are to reduce well-to-wheel (WTW) petroleum energy consumption (PEU), WTW greenhouse gas (GHG) and criteria emissions while maintaining vehicle performance, consumer acceptability and safety. Following the EcoCAR 2 Vehicle Development Process (VDP), HEVT is designing, building, and refining an advanced technology vehicle over the course of the three year competition using a 2013 Chevrolet Malibu donated by GM as a base vehicle.

The Hybrid Electric Vehicle Team (HEVT) of Virginia Tech is excited about the opportunity to apply for participation in the next Advanced Vehicle Technology Competition. EcoCAR 3 is a new four year competition sponsored by the Department of Energy and General Motors with the intention of promoting sustainable energy in the automotive sector. The goal of the competition is to guide students from universities in North America to create new and innovative technologies to reduce the environmental impact of modern day transportation. EcoCAR 3, like its predecessors, will give students hands-on experience in designing and implementing advanced technologies in a setting similar to that of current production vehicles.

Ambient temperature plays an important role in the operational behavior of a vehicle. Temperature variances from 20 F to 72 F to 95 F produce different operation from different HEVs, as prescribed by their respective energy management strategies. The extra variable of Climate Control causes these behaviors to change again. There have been studies conducted on the differences in operational behavior of conventional vehicles as against HEVs, with and without climate control. Lohse-Bush et al conclude that operational behavior of conventional vehicles is much more robust as compared to HEVs and that the effect of ambient temperature is felt more prominently in HEVs (1).

Hybrid electric vehicle (HEV) is one of the most highly pursued technologies for improving energy efficiency while reducing harmful emissions. Thermal modeling and control play an ever increasing role with HEV design and development for achieving the objective of improving efficiency, and as a result of additional thermal loading from electric powertrain components such as electric motor, motor controller and battery pack. Furthermore, the inherent dual powertrains require the design and analysis of not only the optimal operating temperatures but also control and energy management strategies to optimize the dynamic interactions among various components. This paper presents a complete development process and simulation results for an efficient modeling approach with integrated control strategy for the thermal management of plug-in HEV in parallel-through-the road (PTTR) architecture using a flexible-fuel engine running E85 and a battery pack as the energy storage system (ESS).

EcoCAR 2: Plugging in to the Future (EcoCAR) is North America's premier collegiate automotive engineering competition, challenging students with systems-level advanced powertrain design and integration. The three-year Advanced Vehicle Technology Competition (AVTC) series is organized by Argonne National Laboratory, headline sponsored by the U. S. Department of Energy (DOE) and General Motors (GM), and sponsored by more than 30 industry and government leaders. Fifteen university teams from across North America are challenged to reduce the environmental impact of a 2013 Chevrolet Malibu by redesigning the vehicle powertrain without compromising performance, safety, or consumer acceptability. During the three-year program, EcoCAR teams follow a real-world Vehicle Development Process (VDP) modeled after GM's own VDP. The EcoCAR 2 VDP serves as a roadmap for the engineering process of designing, building and refining advanced technology vehicles.

The Wayne State University (WSU) EcoCAR2 student team is investigating powertrain optimizations as a part of their participation in the EcoCAR2 design competition for the conversion of a 2013 Chevrolet Malibu into a plug-in hybrid. EcoCAR2 is the current three-year Department of Energy (DoE) Advanced Vehicle Technical Competition (AVTC) for 15 select university student teams competing on designing, building, and then optimizing their Plug-In Hybrid conversions of GM donated vehicles. WSU's powertrain design provides for approximately 56-64 km (35-40 miles) of electric driving before the Internal Combustion Engine (ICE) powertrain is needed. When the ICE is started, the ICE traditionally goes through a cold start with the engine, transmission, and final drive all at ambient temperature. The ICE powertrain components are most efficient when warmed up to their normal operating temperature, typically around 90-100 °C.

The Wayne State University EcoCAR2 team provided its members with Modeling and Simulation training course for the second summer of the competition. EcoCAR2 is a three-year Advanced Vehicle Technology Competition (AVTC) sponsored by General Motors and the Department of Energy. The course lasted three months and included 45 hours of formal lectures and class hands-on work and an estimated one hundred and fifty hours in home assignments that directly contributed to the team's deliverables. The course described here is unique. The design and class examples were extracted from an in-house complete vehicle simulation and control code to ensure hands-on, interactive training based on real-world problems. The course investigated the physics behind every major powertrain component of a hybrid electric vehicle and the different ways to model the components into a full vehicle simulation.

The Hybrid Electric Vehicle Team (HEVT) of Virginia Tech has achieved the Year 2 goal of producing a 65% functional mule vehicle suitable for testing and refinement, while maintaining the series-parallel plug-in hybrid architecture developed during Year 1. Even so, further design and expert consultations necessitated an extensive redesign of the rear powertrain and front auxiliary systems packaging. The revised rear powertrain consists of the planned Rear Traction Motor (RTM), coupled to a single-speed transmission. New information, such as the dimensions of the high voltage (HV) air conditioning compressor and the P2 motor inverter, required the repackaging of the hybrid components in the engine bay. The P2 motor/generator was incorporated into the vehicle after spreading the engine and transmission to allow for the required space.

The Hybrid Electric Vehicle Team (HEVT) of Virginia Tech is participating in the 2011-2014 EcoCAR 2 competition in which the team is tasked with re-engineering the powertrain of a GM donated vehicle. The primary goals of the competition are to reduce well to wheels (WTW) petroleum energy use (PEU) and reduce WTW greenhouse gas (GHG) and criteria emissions while maintaining performance, safety, and consumer acceptability. To meet these goals HEVT has designed a series parallel plug-in hybrid electric vehicle (PHEV) with multiple modes of operation. This paper will first cover development of the control system architecture with a dual CAN bus structure to meet the requirements of the vehicle architecture. Next an online optimization control strategy to minimize fuel consumption will be developed. A simple vehicle plant model will then be used for software-in-the-loop (SIL) testing to improve fuel economy.

The Wayne State University (WSU) EcoCAR2 student team designed, modeled, Model-In-the-Loop (MIL) tested, Software-In-the-Loop (SIL) simulation tested, and Hardware-In-the-Loop (HIL) simulation tested the team's conversion design for taking a 2013 Chevrolet Malibu and converting it into a Parallel-Through-The-Road (PTTR) plug-in hybrid. The 2013 Malibu is a conventional Front Wheel Drive (FWD) vehicle and the team's conversion design keeps the conventional FWD and adds a Rear Wheel Drive (RWD) powertrain consisting of an electric motor, a single speed reduction gearbox and a differential to drive the rear wheels -where none of these previously existed on the rear wheels. The RWD addition creates the PTTR hybrid powertrain architecture of two driven axles where the mechanical torque path connection between the two powertrains is through the road, rather than a mechanical torque path through gears, chains, or shafts.

The Wayne State University (WSU) EcoCAR2 student team is participating in a design competition for the conversion of a 2013 Chevrolet Malibu into a plug-in hybrid. The team created a repeatable on-road test drive route using local public roads near the university that would be of similar velocity ranges contained in the EcoCAR2 4-Cycle Drive Schedule - a weighted combination of four different EPA-based drive cycles (US06 split into city and highway portions, all of the HWFET, first 505 seconds portion of UDDS). The primary purpose of the team's local on-road route was to be suitable for testing the team's added hybrid components and control strategy for minimizing petroleum consumption and tail pipe emissions. Comparison analysis of velocities was performed between seven local routes and the EcoCAR2 4-Cycle Drive Schedule. Three of the seven local routes had acceptable equivalence for velocity (R₂ ≻ 0.80) and the team selected one of them to be the on-road test drive route.

A crucial step to designing and building more efficient vehicles is modeling powertrain energy consumption. While accurate modeling is indeed key to effective and efficient design, a fundamental understanding of the powertrain and auxiliary systems that contribute to the energy consumption of a vehicle is equally as important. This paper presents a methodology that has been packaged into a tool, called VTool (short for Vehicle Tool), which can be used to estimate the energy consumption of a vehicle powertrain. The method is intrinsically designed to foster understanding of the vehicle powertrain as it relates to energy consumption and losses while still providing reasonably accurate results. This paper briefly explains the methodology of VTool and demonstrates the capability of VTool as a design tool by presenting 4 example exercises.