Search Results

Standard

Overcenter Clutch Spin Test Procedure

2012-10-23

CURRENT

J1079_201210

This SAE Recommended Practice applies to driving ring type overcenter clutches such as are used in industrial power takeoffs.

Standard

Spring-Loaded Clutch Spin Test Procedure

2012-10-23

CURRENT

J1073_201210

This SAE Recommended Practice applies to spring-loaded clutches such as are used with manual shift type transmissions.

Standard

Flywheels for Single-Plate Spring-Loaded Clutches

2012-05-31

CURRENT

J618_201205

This SAE Recommended Practice applies to flywheels for dry spring-loaded clutches used on internal combustion engines. Figure 1 and Tables 1, 2, and 3 report information currently used in the industry. Clutches requiring other dimensions are also manufactured. Dimensions given are primarily for single-plate clutches. Flywheels for two plate clutches have the same dimensions if an adaptor for the intermediate plate and second driven disc is supplied with the clutch. If instead the flywheel is to be extended to adapt the intermediate plate and second driven member, consult the clutch manufacturer for the required J dimension and drive arrangements for the intermediate plate. See SAE J1806 for flywheels for size 14 and 15.5 two plate pull-type clutches.

Standard

Thrust Washers – Design and Application

2011-06-13

CURRENT

J924_201106

This SAE Standard presents the basic size and tolerance information for the design and manufacture of thrust washers. In most cases, the standard employs nominal figures in both metric and inch-pound units and, therefore, does not necessarily provide exact equivalents.

Standard

Split Type Bushings – Design and Application

2011-06-13

CURRENT

J835_201106

This SAE Standard presents the standard sizes, important dimensions, specialized measurement techniques, and tolerances for split type bushings. Both SI and inch sizes are shown; their dimensions are not exact equivalents. New designs shall use SI units. Unless specifically stated as ±, all tolerances are total.

Standard

Engine and Transmission Dipstick Marking

2011-06-13

CURRENT

J614_201106

This SAE Recommended Practice provides information useful in the marking of engine and transmission dipsticks used for fluid level indication.

Standard

Application Guide to Radial Lip Seals

2002-10-25

CURRENT

J946_200210

This SAE Recommended Practice is intended as a guide to the use of radial lip type seals. It has been prepared from existing literature, which includes standards, specifications, and catalog data of both oil seal producers and users and includes generally accepted information and data. The main reason for the preparation of the document is to make standard information available in one document to the users of oil seals.

Standard

Lip Force Measurement--Radial Lip Seals

2002-10-25

CURRENT

J1901_200210

This SAE Recommended Practice defines radial lip force for shaft seals. The principle of lip force measurement is described and the types of radial force measuring devices are discussed. A type of radial force measuring device and procedure for use is recommended.

Standard

Passenger Car and Light Truck Axles

2001-11-01

HISTORICAL

J2200_200111

This SAE Recommended Practice is intended to outline basic nomenclature for axle designs in common use for automotive drives. Over a period of years, there have been many different designs; however, for the purpose of this report, only the most common designs have been selected and only their general construction is illustrated to show the nomenclature of the various parts.

Standard

Guide to the Application and Use of Engine Coolant Pump Face Seals

2000-11-07

HISTORICAL

J1245_200011

This SAE Recommended Practice is intended as a guide in the usage of mechanical face seals for the engine coolant pump application. The main purpose of the document is to fill the void caused by the lack of a ready source of practical information on the design and use of the engine coolant pump face seal. Included in the document is a compilation of present practices, as in a description of the various types of seals, material combinations, design data, tolerances, drawing format, qualification and inspection information, and quality control data. The terminology used throughout the document is recommended and, through common usage, is hoped to promote uniformity in seal nomenclature.

Standard

Lip Force Measurement—Radial Lip Seals

2000-10-09

HISTORICAL

J1901_200010

This SAE Recommended Practice defines radial lip force for shaft seals. The principle of lip force measurement is described and the types of radial force measuring devices are discussed. A type of radial force measuring device and procedure for use is recommended.

Standard

Continuously Variable Transmission Test Code For Passenger Cars

2000-04-12

HISTORICAL

J1618_200004

To measure the performance characteristics of Continuously Variable Transmissions (CVT). It outlines dynamometer tests that cover the range of operation and provides a method of presenting the test data. This procedure must be followed with similar test facilities so that results obtained from different laboratories are comparable.

Standard

ENGINE AND TRANSMISSION DIPSTICK MARKING

1995-06-29

HISTORICAL

J614_199506

This SAE Recommended Practice provides information useful in the marking of engine and transmission dipsticks used for fluid level indication.

Standard

THRUST WASHERS—DESIGN AND APPLICATION

1995-02-01

HISTORICAL

J924_199502

This SAE Standard presents the basic size and tolerance information for the design and manufacture of thrust washers. In most cases, the standard employs nominal figures in both metric and inch-pound units and, therefore, does not necessarily provide exact equivalents.

Standard

SPLIT TYPE BUSHINGS—DESIGN AND APPLICATION

1995-02-01

HISTORICAL

J835_199502

This SAE Standard presents the standard sizes, important dimensions, specialized measurement techniques, and tolerances for split type bushings. Both SI and inch sizes are shown; their dimensions are not exact equivalents. New designs shall use SI units. Unless specifically stated as ±, all tolerances are total.

Standard

DESIGN GUIDE FOR FORMED-IN-PLACE GASKETS

1994-04-05

HISTORICAL

J1497_199404

This SAE Recommended Practice presents information which is intended as a guide for proper designing, selection, application, and servicing of liquid, formed-in-place gasket (FIPG) materials.

Standard

ENGINE WEIGHT, DIMENSIONS, CENTER OF GRAVITY, AND MOMENT OF INERTIA

1992-04-01

HISTORICAL

J2038_199204

This SAE Recommended Practice has been developed to provide a uniform method for reporting the weight, dimensions, center of gravity, and moment of inertia of internal combustion engines. SAE J2038 is not intended to cover the technical interface between the engine and transmission. To locate the rear of the engine crankshaft in relationship to the rear of the flywheel housing, refer to SAE J617.

Standard

APPLICATION GUIDE TO RADIAL LIP SEALS

1991-10-01

HISTORICAL

J946_199110

This SAE Recommended Practice is intended as a guide to the use of radial lip type seals. It has been prepared from existing literature, which includes standards, specifications, and catalog data of both oil seal producers and users and includes generally accepted information and data. The main reason for the preparation of the document is to make standard information available in one document to the users of oil seals.

Standard

PASSENGER CAR AND LIGHT TRUCK AXLES

1991-01-09

HISTORICAL

J2200_199101

This SAE Recommended Practice is intended to outline basic nomenclature for axle designs in common use for automotive drives. Over a period of years, there have been many different designs; however, for the purpose of this report, only the most common designs have been selected and only their general construction is illustrated to show the nomenclature of the various parts.

Standard

LIP FORCE MEASUREMENT, RADIAL LIP SEALS

1990-09-01

HISTORICAL

J1901_199009

This SAE Recommended Practice defines radial lip force for shaft seals. The principle of lip force measurement is described and the types of radial force measuring devices are discussed. A type of radial force measuring device and procedure for use is recommended.