Refine Your Search

Date

Date

Topic

Topic

Washers Parts and Components Documentation Lubricants AGE-3 Aircraft Ground Support Equipment Committee Wear Vehicle dynamics

Search Results

Viewing 1 to 20 of 61
123Next >Last >>
Sort by published
Standard

Ground Support Equipment Hydraulic Systems, Design and Installation, Recommended Practices for
2022-12-16
CURRENT
ARP4943A
This SAE Aerospace Recommended Practice (ARP) covers the design and installation requirements for hydraulic systems (up to 8000 psig [56 MPa]) for ground support equipment (GSE). This ARP is derived from AS5440, which provides hydraulic system requirements for aircraft. The recommendations herein are primarily intended for GSE that exchange hydraulic fluid with the aircraft, such as hydraulic service carts, rather than GSE with non-interfacing hydraulic systems. The GSE may be mobile, portable, or stationary.
Standard

Nose Gear Towbarless Tow Vehicle Basic Test Requirements
2022-09-30
CURRENT
ARP5283B
The purpose of this specification is to provide airplane operators and tow vehicle manufacturers with: a General design and operating requirements pertinent to test and evaluation of towbarless tow vehicles. Specific design requirements are provided in ARP4852 and ARP4853. b Test and evaluation requirements. The results of these test evaluations will determine if the loads induced by the tow vehicle will exceed the design loads of the nose gear, or are within the aircraft manufacturer’s limits so that they do not affect the certified safe limit of the nose gear. The results of these test evaluations will also determine if a stability problem may occur during pushback and/or maintenance towing operations with the tested airplane/tow vehicle combination. This document specifies general test requirements and a test evaluation procedure for towbarless tow vehicles (TLTV) intended for pushback and maintenance towing only.
Standard

Aircraft Maintenance Jacks - General Requirements
2021-09-30
CURRENT
AS4775B
This document covers the general requirements for hydraulic aircraft jacks. It can be applied to tripod, unipod, and axle jacks that may be used on open ramp areas as well as in the aircraft hangar. Throughout this Aerospace Standard, the minimum essential criteria are identified by the key word “shall”. Recommended criteria are identified by use of the key word “should”. Deviation from recommended criteria should only occur after careful consideration and thorough service evaluation have shown alternate methods to provide an equivalent level of safety. The term “vertical load” throughout this Aerospace Standard is defined as the force imposed on the aircraft jack at the airframe jack point.
Standard

Aircraft Tow Bar
2021-04-08
CURRENT
ARP1915E
This SAE Aerospace Recommended Practice (ARP) specifies dimensional and physical requirements of tow bar connections to tractor and aircraft (see Figure 1). It is applicable to all types of commercial transport category aircraft tow bar. The purpose of this SAE Aerospace Recommended Practice (ARP) is to standardize tow bar attachments to airplane and tractor according to the mass category of the towed aircraft, so that one tow bar head with different shear levels can be used for all aircraft that are within the same mass category and are manufactured in compliance with AS1614 or ISO 8267.
Standard

Main Line Aircraft Tow Bar Attach Fitting Interface
2021-04-08
CURRENT
AS1614D
This SAE Aerospace Standard (AS) specifies the interface requirements for tow bar attachment fittings on the nose gear (when towing operations are performed from the nose gear) of conventional tricycle type landing gears of commercial civil transport aircraft with a maximum ramp weight higher than 50,000 kg (110,000 pounds), commonly designated as “main line aircraft”. Its purpose is to achieve tow bar attachment fittings interface standardization by aircraft weight category (which determines tow bar forces) in order to ensure that one single type of tow bar with a standard connection can be used for all aircraft types within or near that weight category, so as to assist operators and airport handling companies in reducing the number of different tow bar types used.
Standard

Aircraft Ground Support Equipment - Wind Stability Determination
2020-04-29
CURRENT
ARP1328D
This SAE Aerospace Recommended Practice (ARP) is intended to recommend: a Uniform criteria for determination of wind loads that aircraft ground support equipment can encounter and yet allow personnel to work safely, b Uniform systems for maintaining stability (i.e., stabilizers, outriggers, spring lockout devices), c Standardization of specific types of interlock systems and actuation systems, d A standard formula with its associated design criteria for calculating the steady-state wind stability (i.e., tip point) for aircraft ground support equipment, e A standard method for testing these systems.
Standard

Aircraft Ground Support Equipment - Wind Stability Determination
2017-05-04
HISTORICAL
ARP1328C
This SAE Aerospace Recommended Practice (ARP) is intended to recommend: a uniform criteria for determination of wind loads that aircraft ground support equipment can encounter and yet allow personnel to work safely, b uniform systems for maintaining stability (i.e., stabilizers, outriggers, spring lockout devices), c standardization of specific types of interlock systems and actuation systems, d a standard formula with its associated design criteria for calculating the steady-state wind stability (i.e., tip point) for aircraft ground support equipment, e a standard method for testing these systems.
Standard

Aircraft Ground Support Equipment - Wind Stability Determination
2012-10-15
HISTORICAL
ARP1328B
This SAE Aerospace Recommended Practice (ARP) is intended to recommend: a uniform criteria for determination of wind loads that aircraft ground support equipment can encounter and yet allow personnel to work safely, b uniform systems for maintaining stability (i.e., stabilizers, outriggers, spring lockout devices), c standardization of specific types of interlock systems and actuation systems, d a standard formula with its associated design criteria for calculating the steady-state wind stability (i.e., tip point) for aircraft ground support equipment, e a standard method for testing these systems.
Standard

Nose Gear Towbarless Tow Vehicle Basic Test Requirements
2012-09-24
HISTORICAL
ARP5283A
The purpose of this specification is to provide airplane operators and tow vehicle manufacturers with: a General design and operating requirements pertinent to test and evaluation of towbarless tow vehicles. Specific design requirements are provided in ARP4852 and ARP4853. b Test and evaluation requirements. The results of these test evaluations will determine if the loads induced by the tow vehicle will exceed the design loads of the nose gear, or are within the aircraft manufacturer’s limits so that they do not affect the certified safe limit of the nose gear. The results of these test evaluations will also determine if a stability problem may occur during pushback and/or maintenance towing operations with the tested airplane/tow vehicle combination. This document specifies general test requirements and a test evaluation procedure for towbarless tow vehicles (TLTV) intended for pushback and maintenance towing only.
Standard

Design and Safety Criteria for Passenger Boarding Stairways
2012-03-28
CURRENT
ARP836C
This SAE Aerospace Recommended Practice (ARP) is broken into various categories for convenience and ease of identification. It is the purpose of this document to provide certain criteria for the design and selection of stairways, for the boarding of passengers onto an aircraft. The criteria presented are limited to those factors which affect the safety of the passengers and are coordinated, where applicable, with the practices of the architectural profession, with respect to the design of stairways. The recommended practices are applicable to both mobile variable-elevation type stairways and to fixed-elevation stairways of the type built into an aircraft fuselage.
Standard

Regional Aircraft Towbar Attach Fitting Interface
2011-06-20
CURRENT
AS5488A
This SAE Aerospace Standard (AS) specifies the interface requirements for towbar attachment fittings on the nose gear (when towing operations are performed from the nose gear) of conventional tricycle type landing gears of commercial civil transport aircraft with a maximum ramp weight between 8600 kg (19 000 lb) and 50 000 kg (110 000 lb), commonly designated as "regional aircraft". Its purpose is to achieve towbar attachment fittings interface standardization by aircraft weight category (which determines towbar forces) in order to ensure that one single type of towbar with a standard connection can be used for all aircraft types within or near that weight category, so as to assist operators and airport handling companies in reducing the number of different towbar types used.
Standard

Aircraft Maintenance Jacks - General Requirements
2011-01-14
HISTORICAL
AS4775A
This document covers the general requirements for hydraulic aircraft jacks. It can be applied to tripod, unipod, and axle jacks that may be used on open ramp areas as well as in the aircraft hanger. Throughout this Aerospace Standard, the minimum essential criteria are identified by the key word “shall”. Recommended criteria are identified by use of the key word “should”. Deviation from recommended criteria should only occur after careful consideration and thorough service evaluation have shown alternate methods to provide an equivalent level of safety. The term “vertical load” throughout this Aerospace Standard is defined as the force imposed on the aircraft jack at the airframe jack point.
123Next >Last >>
X