Search Results

Standard

Engine Flywheel Housings with Sealed Flanges

2012-10-23

CURRENT

J1172_201210

This SAE Recommended Practice defines flywheel housing flange configurations for applications requiring "O" ring sealing of the flange pilot bore. Table 1 and Figure 1 show dimensions that are different from those in SAE J617. All other dimensions and tolerances of SAE J617 apply.

Standard

Industrial Power Take-Offs With Driving Ring-Type Overcenter Clutches

2012-10-23

CURRENT

J621_201210

This SAE Standard defines installation dimensions of industrial power take-offs with driving ring-type overcenter clutches. Table 1 and Figure 1 give dimensions for power take-offs. For dimensions and tolerances of power take-off flanges and flywheels, see SAE J617 and J620, respectively.

Standard

Housing Internal Dimensions for Single- and Two-Plate Spring-Loaded Clutches

2012-05-31

CURRENT

J373_201205

This SAE Recommended Practice defines the minimum internal dimensions for clutch housings to provide adequate clearance for single- and two-plate spring-loaded clutches. (See Figure 1.) Consult SAE J617 for housing flange dimensions. Consult SAE J618 and J619 for spring-loaded clutch flywheel dimensions F and G and other dimensional data. Table 1 provides housing minimum internal dimensions for single- and two-plate spring-loaded clutches.

Standard

Flywheels for Two-Plate Spring-Loaded Clutches

2012-05-31

CURRENT

J619_201205

This SAE Recommended Practice defines flywheel configuration to promote standardization of flywheels for dry spring-loaded clutches. Clutches to fit flywheels with configurations per this document may not be commercially available. Availability should be ascertained prior to flywheel design Figure 1 and Table 1A.

Standard

Engine Testing with Low-Temperature Charge Air-cooler Systems in a Dynamometer Test Cell

2011-09-06

CURRENT

J1937_201109

The methods presented in this SAE Recommended Practice apply to the controlled testing of low-temperature charge, air-cooled, heavy-duty diesel engines. This document encompasses the following main sections: a Definitions of pertinent parameters b Vehicle testing to determine typical values for these parameters c Description of the setup and operation of the test cell system d Validation testing of the test cell system While not covered in this document, computer modeling of the vehicle engine cooler system is recognized as a valid tool to determine cooler system performance and could be utilized to supplement the testing described. However, adequate in-vehicle testing should be performed to validate the model before it is used for the purposes outlined. The procedure makes references to test cycles that are prescribed by the United States Environmental Protection Agency (US EPA) and are contained in the Code of Federal Regulations.

Standard

Engine and Transmission Dipstick Marking

2011-06-13

CURRENT

J614_201106

This SAE Recommended Practice provides information useful in the marking of engine and transmission dipsticks used for fluid level indication.

Standard

Design Guide for Formed-in-Place Gaskets

2008-07-08

CURRENT

J1497_200807

This SAE Recommended Practice presents information which is intended as a guide for proper designing, selection, application, and servicing of liquid, formed-in-place gasket (FIPG) materials.

Standard

Engine Coolant Pump Seals

2002-10-25

CURRENT

J780_200210

This SAE Standard outlines physical dimensions and nomenclature for the sizes of seals commonly used in engine coolant pumps of automotive type engines. Its purpose is to define a standard envelope to accommodate installation of various seal designs and to promote uniformity in seal nomenclature. (See Figures 1 to 5.)

Standard

Guide to the Application and Use of Engine Coolant Pump Face Seals

2002-10-25

CURRENT

J1245_200210

This SAE Recommended Practice is intended as a guide in the usage of mechanical face seals for the engine coolant pump application. The main purpose of the document is to fill the void caused by the lack of a ready source of practical information on the design and use of the engine coolant pump face seal. Included in the document is a compilation of present practices, as in a description of the various types of seals, material combinations, design data, tolerances, drawing format, qualification and inspection information, and quality control data. The terminology used throughout the document is recommended and, through common usage, is hoped to promote uniformity in seal nomenclature.

Standard

Engine Testing with Low-Temperature Charge Air-cooler Systems in a Dynamometer Test Cell

2002-10-21

HISTORICAL

J1937_200210

The methods presented in this SAE Recommended Practice apply to the controlled testing of low-temperature charge, air-cooled, heavy-duty diesel engines. This document encompasses the following main sections: a Definitions of pertinent parameters b Vehicle testing to determine typical values for these parameters c Description of the setup and operation of the test cell system d Validation testing of the test cell system While not covered in this document, computer modeling of the vehicle engine cooler system is recognized as a valid tool to determine cooler system performance and could be utilized to supplement the testing described. However, adequate in-vehicle testing should be performed to validate the model before it is used for the purposes outlined. The procedure makes references to test cycles that are prescribed by the United States Environmental Protection Agency (US EPA) and are contained in the Code of Federal Regulations.

Standard

Diesel Catalytic Converter Nomenclature and Terminology

2001-10-30

CURRENT

J1643_200110

This SAE Draft Technical Report applies to nomenclature of diesel engine catalytic converter parts and various configurations.

Standard

Engine Coolant Pump Seals

2000-11-07

HISTORICAL

J780_200011

This SAE Standard outlines physical dimensions and nomenclature for the sizes of seals commonly used in engine coolant pumps of automotive type engines. Its purpose is to define a standard envelope to accommodate installation of various seal designs and to promote uniformity in seal nomenclature. (See Figures 1 to 5.)

Standard

Guide to the Application and Use of Engine Coolant Pump Face Seals

2000-11-07

HISTORICAL

J1245_200011

This SAE Recommended Practice is intended as a guide in the usage of mechanical face seals for the engine coolant pump application. The main purpose of the document is to fill the void caused by the lack of a ready source of practical information on the design and use of the engine coolant pump face seal. Included in the document is a compilation of present practices, as in a description of the various types of seals, material combinations, design data, tolerances, drawing format, qualification and inspection information, and quality control data. The terminology used throughout the document is recommended and, through common usage, is hoped to promote uniformity in seal nomenclature.

Standard

Manual Transmission and Transaxle Efficiency and Parasitic Loss Measurement

1999-08-30

HISTORICAL

J2453_199908

Because of the intense focus on CAFE and fuel emission standards, optimization of the automobile drivetrain is imperative. In light of this, component efficiencies have become an important factor in the drivetrain decision-making process. It has therefore become necessary to develop a universal standard to judge transmission efficiency. This SAE Recommended Practice specifies the dynamometer test procedure which maps a manual transmission’s efficiency. The document is separated into two parts. The first compares input and output torque throughout a specified input speed range in order to determine “in-gear” transmission efficiency. The second procedure measures parasitic losses experienced while in neutral at nominal idling speeds and also churning losses while in gear. The application of this document is intended for passenger car and light truck. All references to transmissions throughout this document include transaxles.

Standard

SEALS—TERMINOLOGY OF RADIAL LIP

1997-05-01

HISTORICAL

J111_199705

The purpose of this SAE Recommended Practice is to provide a glossary of radial seal terms and nomenclature which are normally encountered in the design, manufacture, installation, testing, inspection, and failure mode analysis of radial seals. The information will aid in the understanding and communication among those people associated with radial seals.

Standard

ENGINE AND TRANSMISSION DIPSTICK MARKING

1995-06-29

HISTORICAL

J614_199506

This SAE Recommended Practice provides information useful in the marking of engine and transmission dipsticks used for fluid level indication.

Standard

INDUSTRIAL POWER TAKE-OFFS WITH DRIVING RING-TYPE OVERCENTER CLUTCHES

1995-03-08

HISTORICAL

J621_199503

This SAE Standard defines installation dimensions of industrial power take-offs with driving ring-type overcenter clutches. Table 1 and Figure 1 give dimensions for power take-offs. For dimensions and tolerances of power take-off flanges and flywheels, see SAE J617 and J620, respectively.

Standard

FLYWHEELS FOR TWO-PLATE SPRING-LOADED CLUTCHES

1993-12-01

HISTORICAL

J619_199312

This SAE Recommended Practice defines flywheel configuration to promote standardization of flywheels for dry spring-loaded clutches. Clutches to fit flywheels with configurations per this document may not be commercially available. Availability should be ascertained prior to flywheel design Figure 1 and Table 1A.

Standard

INSTRUMENTATION AND TECHNIQUES FOR EXHAUST GAS EMISSIONS MEASUREMENT

1993-09-09

HISTORICAL

J254_199309

This SAE Recommended Practice establishes uniform laboratory techniques for the continuous and bag-sample measurement of various constituents in the exhaust gas of the gasoline engines installed in passenger cars and light-duty trucks. The report concentrates on the measurement of the following components in exhaust gas: hydrocarbons (HC), carbon monoxide (CO), carbon dioxide (CO2), oxygen (O2), and nitrogen oxides (NOx). NOx is the sum of nitric oxide (NO) and nitrogen dioxide (NO2). A complete procedure for testing vehicles may be found in SAE J1094. This document includes the following sections: 1 Scope 2 References 3 Emissions Sampling Systems 4 Emissions Analyzers 5 Data Analysis 6 Associated Test Equipment 7 Test Procedures

Standard

STATIC AND RECIPROCATING ELASTOMERIC TRANSMISSION SEALS

1993-03-26

HISTORICAL

J654_199303

This SAE Recommended Practice is intended as a guide to the design and use of static and reciprocating elastomeric transmission seals. It has been prepared from existing literature, which includes standards, specifications, and catalog data of both producers and users and includes generally-accepted information and data. The main reason for the preparation of the document is to make standard information available in one document to the users of static and reciprocating elastomeric transmission seals.