Refine Your Search

Date

Date

Topic

Topic

Tests and Testing AGE-3 Aircraft Ground Support Equipment Committee Commercial vehicles Identification Chemicals Diesel / compression ignition engines Wear

Search Results

Viewing 1 to 20 of 81
123Next >Last >>
Sort by published
Standard

Impulse Towing Loads
2023-04-03
CURRENT
AIR6906
This SAE Aerospace Information Report (AIR) provides information about impulse loads that occur during normal aircraft towing operations. An instrumented tow bar was used to characterize towing loads. Suggestions to minimize impulse loads by reducing the tow bar to tow vehicle gap are described.
Standard

Measurement of Exterior Sound Level of Specialized Aircraft Ground Support Equipment
2021-09-30
CURRENT
ARP1801A
The scope of this SAE Recommended Practice covers specialized internal combustion engine powered equipment used in support of aircraft operations. The equipment may be self-propelled, truck mounted, trailer mounted, skid mounted or stationary. It does not include construction equipment or equipment designed primarily for operation on highways or within factories or building areas. NOTE: Equivalent methodology is provided in (CEN) EN 1915-4, Aircraft ground support equipment - General requirements - Part 4: Noise measurement methods and reduction, to be used for measurements conforming to the EU Machinery Directive
Standard

Pallet/Container Loader Auto-Levelling Systems
2021-09-30
CURRENT
ARP4776
The data in this document is, at this stage, primarily concerned with the interface of pallet/container loaders and lower-deck compartments of standard and wide-body aircraft although the principles illustrated may be applied to the main-decks of narrow and wide-body aircraft. NOTE: For the purpose of this document, in accordance with Part 3 of the Directives for the technical work of ISO and with accepted IATA practice, minimum essential criteria defined by the word "shall" are absolute requirements. Recommended criteria identified by the word "should", while considered important, are not mandatory.
Standard

Method of Testing Pre-Conditioned Air Equipment
2021-04-08
CURRENT
ARP5374B
This SAE Aerospace Recommended Practice (ARP) applies to Point-Of-Use, Central and Mobile Pre-Conditioned Air Equipment. It does not apply to aircraft mounted equipment.
Standard

Aircraft Tow Bar
2021-04-08
CURRENT
ARP1915E
This SAE Aerospace Recommended Practice (ARP) specifies dimensional and physical requirements of tow bar connections to tractor and aircraft (see Figure 1). It is applicable to all types of commercial transport category aircraft tow bar. The purpose of this SAE Aerospace Recommended Practice (ARP) is to standardize tow bar attachments to airplane and tractor according to the mass category of the towed aircraft, so that one tow bar head with different shear levels can be used for all aircraft that are within the same mass category and are manufactured in compliance with AS1614 or ISO 8267.
Standard

Maintenance of Batteries and Battery Charging and Servicing Facilities
2020-09-23
CURRENT
AIR1898A
This SAE Aerospace Information Report (AIR) covers, and is restricted to, hands-on servicing/ maintenance of industrial lead acid batteries used solely for motive power and exclusively for ground support equipment (GSE). It does not address or pertain to automotive-type SLI (starting-lighting-ignition) batteries or any other types of batteries (such as nickel-cadmium, zinc, or lithium batteries) which may be on-board airport GSE for either motive power or auxiliary uses. Similarly, the battery servicing and charging facilities described herein are those intended exclusively for industrial lead acid batteries.
Standard

Fuels in Ground Support Equipment (Other Than Gasoline or Diesel)
2020-09-23
CURRENT
AIR5373A
This SAE Aerospace Information Report (AIR) is intended as a source of comparative information and is subject to change to keep pace with experience and technical advances. This document describes currently used fuels and fuels which may be used in the future. Conventional gasoline and diesel fuels are intentionally omitted from this document.
Standard

Charger for Battery Powered Ground Support Equipment
2020-09-23
CURRENT
ARP1816D
This SAE Aerospace Recommended Practice (ARP) describes three general types of Ground Support Equipment (GSE) battery chargers. The battery charger typically requiring up to 8 hours to recharge a 100% discharged battery, hereafter called “Conventional Charger.” A charger, hereafter called “Opportunity Charger,” which has the ability to charge at a slightly faster rate than a conventional charger. A charger, hereafter called “Fast Charger,” which has the ability to charge at a much faster rate than a conventional charger. Recommendations that apply to all types will refer generically to “charger.”
Standard

Baggage/Cargo Trailer Requirements
2020-09-23
CURRENT
ARP1348B
This SAE Aerospace Recommended Practice (ARP) applies to airline trailer equipment with four wheel running gear pulled and steered through an integral tow bar, for use on airport ramps and other airport areas for transporting baggage, freight, and other materials. This ARP can apply to any airline/airport trailer chassis regardless of its equipment; the trailer bed can be designed to carry either bulk baggage/cargo, or a cargo unit load device by means of a rollerized conveyor system, or a piece of aircraft servicing equipment (e.g., ground power unit, air start unit, etc.).
Standard

Aircraft Markings for Ground Support Equipment Alignment
2020-04-24
CURRENT
AS6896
The purpose of this document is to provide a standard for aircraft fuselage markings located at the doors used for ground servicing operations. These markings can be used by all GSE that will dock at the aircraft. These markings may be used for one or several phases of the GSE positioning relative to the aircraft process: GSE alignment during approach, GSE final docking, and GSE auto leveling. It is not the purpose of this standard to describe the different technologies, cameras, or other equipment that can be mounted on GSE to utilize these markings. The aircraft that may use these markings will have a fuselage diameter of 3 m or more.
Standard

Aircraft Jacking Pads Adapters and Sockets Design and Installation of
2019-03-29
CURRENT
AS8091A
This SAE Aerospace Standard (AS) provides requirements for design and installation of aircraft jacking pad adapters and the mating jack socket interface to permit use of standard jacking equipment to be used in civil and military transport aircraft. The adapter defined herein shall be the key interface between the aircraft and the aircraft jack(s).
Standard

Aircraft Ground Support Equipment – General Requirements
2018-02-12
CURRENT
ARP1247E
This SAE Aerospace Recommended Practice (ARP) outlines the basic general design requirements for ground support equipment used in the civil air transport industry. It is intended to assist in standardizing requirements for various configurations of equipment. For procurement of equipment, sections of this document should be specified with due consideration of the functional and environmental requirements of the equipment, and to the relative cost of satisfying those requirements.
123Next >Last >>
X