Search Results

Although not limited to, these installations are normally used on trucks considered as Medium Duty (Class 6 and 7), as well as Heavy Duty (Class 8).

This SAE Recommended Practice is intended as a guide toward standard practice but may be subject to frequent change to keep pace with experience and technical advances.

This SAE Standard applies only to new winches which are primarily designed for intermittent pulls and lifts and whose configuration and condition are the same as when they were shipped by the manufacturer. They are not intended to be used in any manner for the movement of personnel. They may be driven by any power source recommended by the manufacturer and will be capable of being powered in either direction. They will be equipped with an automatic safety brake system to control a load when lowering under power and positively hold a load when power is not being delivered to the winch. A hydraulic flow control valve or similar device may be used in the brake system to control a load when lowering under power. A clutch to release the drum for “free-spooling” may be provided and will be designed not to disengage itself under load. A drag brake may be provided to control “free-spooling,” but will not be relied on to control or hold a load.

This SAE Recommended Practice is intended to serve as a reference for the amount of torque that a Power Take-Off can induce on the transmission mounting pad. This document will apply to six-bolt, eight-bolt, and rear mounted power take-offs.

This SAE Standard describes a procedure to be used to evaluate a disturbance known as “idle gear rattle” which can exist in vehicles equipped with manual transmissions and clutches. Other types of noises associated with operation at idle are also briefly described.

Although not limited to, these flywheels are normally used on trucks considered as Medium-Duty (Class 6 and 7), as well as Heavy-Duty (Class 8) trucks.

This SAE Recommended Practice is prepared as a guideline to improve and maintain the quality of remanufactured automotive products. Installation of remanufactured or rebuilt products is often an economical way to repair a vehicle even though they may not fully be equivalent to original equipment parts. Before processing any part, a remanufacturer should determine if the original design and present condition of the core are suitable for remanufacturing, so as to provide durable operation of the part as well as acceptable performance when installed in a vehicle. The remanufacturer should also carefully consider the safety aspects of the product and any recommendations of the original manufacturer related to remanufacturing or rebuilding their product.

Provide standard shift pattern guidelines for manual transmission shift controls in light, medium, and heavy trucks and buses.

This SAE Recommended Practice describes STANDARD-DUTY and EXTREME-DUTY Pilot Bearing requirements and sizes for class 6, 7, and 8 on-highway trucks and buses that use diesel engines and manual transmissions. The recommendations may apply to a wide range of other pilot-bearing applications, such as agricultural, industrial, and construction equipment.

As the number of Hydraulic Hybrid Powertrain equipped motor vehicles has increased, the number of terms, abbreviations, and acronyms which describe various components of these systems has increased. For the sake of industry standardization and to bring some order to the proliferation of such terms, abbreviations, and acronyms, the SAE Truck and Bus Hydraulic Hybrid committee prepared this document.

This SAE Recommended Practice documents the typical transmission interface dimensions that are used with 14-in and larger pull-type clutches. See Figure 1.

Because of the intense focus on fuel economy and fuel emission standards, it has become imperative to optimize vehicle drivetrains. In light of this, component efficiencies have become an important factor in the drivetrain decision-making process. It has therefore become necessary to develop a universal standard to judge transmission efficiency. This SAE Recommended Practice specifies a test procedure which maps torque transmittal efficiency and parasitic losses for manual transmissions. The application of this document is intended for manual transmissions used in light (class 4) through heavy truck applications with both simple and compound ratio structures. This document is separated into two parts. The first compares input and output torque throughout a specified input speed range in order to determine the overall transmission efficiency. This test is used to evaluate all forward gears; testing in reverse is optional.

Provide standard shift pattern guidelines for manual transmission shift controls in light, medium, and heavy trucks and buses.

This SAE Recommended Practice has been adopted by SAE to specify: a A basis for net engine retarder power rating b Reference inlet air test conditions c A method for correcting observed engine retarder power to reference conditions d A method for determining net engine retarder power with a dynamometer

This SAE Recommended Practice has been adopted by SAE to specify: a A basis for net engine retarder power rating b Reference inlet air test conditions c A method for correcting observed engine retarder power to reference conditions d A method for determining net engine retarder power with a dynamometer

This SAE Recommended Practice outlines basic nomenclature in common use for truck and bus drive axle designs. Over a period of years there have been many different designs introduced; however, for this report, only the most common have been selected and only their general construction is illustrated to show the nomenclature of the various parts.

This SAE Recommended Practice is intended as a guide toward standard practice but may be subject to frequent change to keep pace with experience and technical advances.

This SAE Standard applies only to new winches which are primarily designed for intermittent pulls and lifts and whose configuration and condition are the same as when they were shipped by the manufacturer. They are not intended to be used in any manner for the movement of personnel. They may be driven by any power source recommended by the manufacturer and will be capable of being powered in either direction. They will be equipped with an automatic safety brake system to control a load when lowering under power and positively hold a load when power is not being delivered to the winch. A hydraulic flow control valve or similar device may be used in the brake system to control a load when lowering under power. A clutch to release the drum for “free-spooling” may be provided and will be designed not to disengage itself under load. A drag brake may be provided to control “free-spooling,” but will not be relied on to control or hold a load.

This SAE Recommended Practice is intended to serve as a reference for the amount of torque that a Power Take-Off can induce on the transmission mounting pad. This document will apply to six-bolt, eight-bolt, and rear mounted power take-offs.

This SAE Recommended Practice documents the typical transmission interface dimensions that are used with 14-in and larger pull-type clutches. See Figure 1.