Search Results

The Fluid Science Laboratory (FSL) is an advanced multi-user facility for conducting fluid physics research in microgravity conditions. It will be installed in the Columbus module of the International Space Station (ISS) scheduled for launch in 2004. FSL is being developed by a European industrial team, led by ALENIA SPAZIO of Italy, and managed by the European Space Agency (ESA). The FSL Thermal Environment Control (TEC) establishes a defined thermal environment during the complete experiment duration to keep the experiment and the supporting subsystems within their thermal requirements. The TEC is further subdivided into three sections. The Air Cooling Section is based on the Avionics Air Assembly (AAA) which generates air streams inside the Facility to collect, by forced convection, the waste heat from the electronics belonging to the various Subsystems. The Secondary Water Loop (SWL) cooling Section provides the cooled water to the Experiment Container.

The Columbus laboratory module for the International Space Station (ISS) uses active thermal control for cooling of avionics and payload in the pressurized compartment. The Active Thermal Control Subsystem (ATCS) is based on a water loop rejecting waste heat to the Medium Temperature Heat Exchanger and Low Temperature Heat Exchanger on Node 2, part of the US Segment of the ISS. Flow and temperature control in the ATCS is achieved by means of the Water Pump Assembly (WPA) and the 3-Way Modulating Valve (WTMO) units. For the flow control the WPA speed is commanded so that a fixed pressure drop is maintained over the plenum with the avionics and payload branches. Adjusting the WTMO internal flow split permit the two active units to perform the CHX and plenum inlet temperature control. The WPA includes a filter and an accumulator to control the pressure in the ATCS and to compensate for leakage and temperature-dependent volume variations.

ESA and NASA agencies agreed to run an interface compatibility test at the EADS facility between the Columbus flight module and a duplicate ground unit of a currently on-orbit US International Standard Payload Rack, the Human Research Facility (HRF) Flight Prototype Rack (FPR). The purpose of the test was to demonstrate the capability to run US payloads inside the European ISS module Columbus. One of the critical aspects to be verified to ensure suitable operations of the two systems was the combined performance of the hydraulic controls resident in the HRF and Columbus coolant loops. A hydraulic model of the HRF FPR was developed and combined with the Columbus Active Thermal Control System (ATCS) model. Several coupled thermal-hydraulic test cases were then performed, preceded by mathematical analysis, required to predict safe test conditions and to optimize the Columbus valve configurations.

The Visual Video Target Switching Unit (VVTSU) is the control unit dedicated to the Visual Video Target (VVT). The VVTSA, grouping VVTSU and VVT, is a “two-boxes assy”, externally located on ATV Front Cone, used to allow ATV monitoring by crewmembers inside the ISS Service Module, during the final approach up to 500 m from the docking port. Alenia Spazio is the responsible of VVTSA and in particular of the design, assembly and qualification of the VVSTU unit: an Engineering Model (for avionic tests), a Qualification Model and two Flight Units (+ 1 Spare) have been designed, assembled and verified in Torino and L’ Aquila Laboratories. The VVTSU is powered during the Rendezvous and it presents a high power dissipation, if compared with the reduced dimensions. The thermal control of this unit has been realized using passive means: a high conductive coupling with the fixation bracket, jointed with a radiator on the VVTSU top face.

The Automated Transfer Vehicle (ATV) Thermal Control System (TCS) has the task to ensure the required internal environment at level of pressurized module and to thermally control the not pressurised modules and installed equipment, using passive and active control means, in response to the relevant applicable requirements. The ATV vehicle is assially subdivided into three main modules: the Integrated Cargo Carrier (ICC), the Equipped Avionics Bay (EAB) and the Equipped Propulsion Bay (EPB). Each of these modules present elaborated and specific thermal design solutions, to satisfy the different required operative tasks. The extensive thermal analysis campaign performed at ATV vehicle level and in progress for the next Qualification Review (QR) to justify and support the thermal control design solutions and verification status is described.