Search Results

The effect of the shape of the EOI was investigated through a pressure-modulated injection system in order to improve the understanding of the last portion of the traditional diesel diffusion combustion process. Here, the combustion recession at EOI is when the combustion of a mixing controlled diesel jet recedes backwards toward the fuel injector nozzle orifice. Combustion recession was observed using combustion luminosity imaging filtered at 309 nm to capture OH* chemiluminescence and 430 nm to capture CH* chemiluminescence, although soot Natural Luminosity (NL) will also be visible in these measurements. Experimental spray vessel results show that for relatively slow EOI decelerations below 1 ×106 to 2 ×106 m/s2, combustion strongly recesses completely back to the nozzle in both OH* and CH*/NL imaging. 1-D jet mixing calculations add support that this strong recession is indeed fuel rich.

How will a mechanic troubleshoot the heavy duty vehicle of the future? Will he or she have to be both retriever and integrator of data collected from multiple black boxes on the vehicle? How many tools will it take? Is there a definition of a vehicle system “diagnostic environment” that needs to be developed in order to create a solution to this problem? This paper will attempt to create the system focus for vehicle diagnostics that is required if this industry is to successfully produce the integrated electronic vehicle of the future. Both the on-board and off-board requirements of the diagnostic environment will be examined.

A quasidimensional engine simulation which uses the concepts of fractal geometry to model the effects of turbulence on flame propagation in a homogeneous charge SI engine has been developed. Heat transfer and blowby/crevice flow submodels are included in this code and the submodels chosen are found to be reasonable. The model predictions of cylinder pressure histories are then compared with experimental data over a range of loads, equivalence ratios, and engine speeds. The model is not adjusted in any manner to yield better agreement with the data, other than by tuning the simple turbulence model used so as to yield agreement with data for the nonreacting flow. However, current information about the flame wrinkling scales in an engine is inadequate. Therefore, predictions are made for three different assumptions about the flame wrinkling scales which span the range of physically possible scales.

The HELP Program and Crescent Demonstration Project is a bi-national multi-jurisdictional cooperative research and demonstration project involving the public and private sectors in an application of advancing technologies in the creation of an integrated heavy vehicle management system with applications to both highway and vehicle systems. This initiative is a leading example of the Intelligent Vehicle Highway Systems (IVHS) in commercial vehicle operations (CVO). The selected technologies are being integrated into a heavy vehicle management system. These technologies include: (1) automatic vehicle identification (AVI), (2) weigh-in-motion (WIM), (3) automatic vehicle classification (AVC), (4) data communication networks and systems integration. The program, initiated approximately eight years ago, consists of three phases which include assessing the feasibility of the concept, technical studies involving laboratory and field tests, and, lastly, the demonstration phase.

This paper describes a study to demonstrate the feasibility of developing an acoustic encapsulation to reduce airborne noise from a commercial diesel engine. First, the various sources of noise from the engine were identified using Nearfield Acoustical Holography (NAH). Detailed NAH measurements were conducted on the four sides of the engine in an engine test cell. The main sources of noise from the engine were ranked and identified within the frequency ranges of interest. Experimental modal analysis was conducted on the oil pan and front cover plate of the engine to reveal correlations of structural vibration results with the data from the NAH. The second phase of the study involved the design and fabrication of the acoustical encapsulation (noise covers) for the engine in a test cell to satisfy the requirements of space, cost and performance constraints. The acoustical materials for the enclosure were selected to meet the frequency and temperature ranges of interest.

Caterpillar Fuel Systems is developing a family of next generation electronic unit injectors that provide the fundamental injection characteristics necessary for emissions and performance improvements for future direct-injection diesel engines. This paper describes the development and design of the mechanically actuated version of Caterpillar's advanced electronic unit injector fuel system to meet the engine customer driven requirements for enhanced injection characteristics with reliability and durability improvements.

The basic process of spark ignition in engines has changed little over the more than 100 years since its first application. The rapid evolution of several advanced engine concepts and the refinement of existing engine designs, especially applications of power boost technology, have led to a renewed interest in advanced spark ignition concepts. The increasingly large rates of in-cylinder dilution via EGR and ultra-lean operation, combined with increases in boost pressures are placing new demands on spark ignition systems. The challenge is to achieve strong and consistent ignition of the in-cylinder mixture in every cycle, to meet performance and emissions goals while maintaining or improving the durability of ignitor. The application of railplug ignition to some of these engine systems is seen as a potential alternative to conventional spark ignition systems that may lead to improved ignition performance.

This paper documents an inverse visible element Rayleigh integral (VERI) approach. The VERI is a fast though approximate method for predicting sound radiation that can be used in the place of the boundary element method. This paper extends the method by applying it to the inverse problem where the VERI is used to generate the acoustic transfer matrix relating the velocity on the surface to measurement points. Given measured pressures, the inverse VERI can be used to reconstruct the vibration of a radiating surface. Results from an engine cover and diesel engine indicate that the method can be used to reliably quantify the sound power and also approximate directivity.

The critical particle size for a high-pressure injection system was determined. Various double-cut test dusts ranging from 0 to 5 μm to 10 to 20 μm were evaluated to determine which test dust caused the high-pressure system to fail. With the exception of the 0- to 5-μm test dust, all test dust ranges caused failure in the high-pressure injection system. Analysis of these evaluations revealed that the critical particle size, in initiating significant abrasive wear, is 6 to 7 μm. Wear curve formulas were generated for each evaluation. A formula was derived that allows the user to determine if the fuel filter effluent will cause harmful damage to the fuel system based on the number of 5-, 10-, and 15-μm particles per milliliter present. A methodology was developed to evaluate fuel filter performance as related to engine operating conditions. The abrasive methodology can evaluate online filter efficiency and associated wear in a high-pressure injection system.

Joint strength of a vibration welded air intake manifold has been optimized by controlling the process parameters. Key process parameters are: Clamp pressure, bead melt down displacement and vibration amplitude. The present study has investigated the combined effect of the vibration welding process parameters on the weld joint strength of a manifold by using a factorial DOE (Design of Experiment) with center points. The result of the DOE study revealed that the burst strength can vary as much as 50% across the process window investigated. Response surface of strength, which was developed as a function of the process variables, can be used for process control in the production plant. The weld strength values of Nylon 6 and Nylon 66 materials are also compared across the wide range of the process window.

An important component in many hybrid electric vehicle (HEV) concepts is the load leveling device (LLD). The best type of LLD for HEVs is under debate. This paper identifies the important concept selection criteria for the three leading types of LLDs being considered for use in HEVs. The performance of electrochemical batteries, ultracapacitors, and flywheels is compared using these criteria. The concept selection methodology indicates that at the present time flywheels show the most promise for development for use in a hybrid electric vehicle. The use of this type of selection methodology is a powerful tool in identifying concepts worthy of development as well as determining performance criteria in need of improvement within each concept.

An infrared fiber optic instrumented spark plug probe has been used to measure the fuel concentration in the vicinity of the spark gap in a port injected gasoline fueled SI engine. The probe measured the fuel concentration spatially averaged over a distance of 6.3 mm near the spark plug for consecutive firing cycles. The crank angle resolution of the measurements was 2.5 degrees, for a temporal resolution of between 0.9 and 0.3 ms depending on the engine speed. Quantitative measurements of the fuel concentration in the pre-ignition regions of the engine cycle were obtained. Qualitative results are reported for unburned hydrocarbons in the post-combustion regions. The measurements were made in a single cylinder research engine over a range of speed, load, and stoichiometric conditions. Strong mixture inhomogeneities were measured during the intake stroke and the inhomogeneities decreased through the compression stroke.

A liquid-phase port injection system for liquefied petroleum gas (LPG) generally consists of a fuel storage tank with extended capability of operating up to 600 psi, a fuel pump, and suitable fuel lines to and from the LPG fuel injectors mounted in the fuel rail manifold. Port injection of LPG in the liquid phase is attractive due to engine emissions and performance benefits. However, maintaining the LPG in the liquid phase at under-hood conditions and re-starting after hot soak can be difficult. Multiphase behavior within a liquid-phase LPG injection system was investigated computationally and experimentally. A commercial chemical equilibrium code (ASPEN PLUS™) was used to model various LPG compositions under operating conditions.

A team of student engineers at the University of Texas at Austin has designed and built “Texas Native Sun”, a solar powered vehicle for competition in GM Sunrayce U.S.A. The single-seat vehicle uses conventional photovoltaic solar cells to produce electricity for vehicle propulsion. The vehicle features graphite/epoxy composite monocoque construction, a high power-density permanent magnet electric motor, a mechanical/hydraulic continuously variable transmission, nickel-hydrogen satellite batteries, and a composite leaf spring suspension. The race strategies and tactics of energy management are optimized through use of a computer code which simulates the vehicle under race conditions. Much of the technology employed in the vehicle may one day become an ordinary part of future transportation systems which seek greater energy efficiency and less damage to the environment.

A new Computational Fluid Dynamics (CFD) code has been developed in order to overcome the deficiencies of traditional grid generation and mesh motion methods. The new code uses a modified cut-cell Cartesian technique that eliminates the need for the computational grid to coincide with the geometry of interest. The code also includes state-of-the-art numerical techniques and sub-models for simulating the complex physical and chemical processes that occur in engines. Features such as shared and distributed memory parallelization, a multigrid pressure solver and user-specified grid embedding allow for efficient simulations while maintaining the grid resolution necessary for accurate engine modeling. In addition, a new Adaptive Grid Embedding (AGE) technique has been developed and implemented. Sub-models for turbulence, spray injection, spray breakup, liquid drop dynamics, ignition, combustion and emissions are also included in the code.

This paper presents the latest developments in the design and performance of an electronic particulate matter (PM) sensor developed at The University of Texas at Austin (UT) and suitable, with further development, for applications in active engine control of PM emissions. The sensor detects the carbonaceous mass component of PM in the exhaust and has a time-resolution less than 20 (ms), allowing PM levels to be quantified for engine transients. Sample measurements made with the sensor in the exhaust of a single-cylinder light duty diesel engine are presented for both steady-state and transient operations: a steady-state correlation with gravimetric filter measurements is presented, and the sensor response to rapid increases in PM emission during engine transients is shown for several different tip-in (momentary increases in fuel delivery) conditions.

A general combustion model, in the context of large eddy simulations, was developed to simulate the full range of combustion in conventional diesel-type and HCCI-type diesels. The combustion model consisted of a Chemkin sub-model and an Extended Flamelet Time Scale (EFTS) sub-model. Specifically, Chemkin was used to simulate auto-ignition process. In the post-ignition phase, the combustion model was switched to EFTS. In the EFTS sub-model, combustion was assumed to be a combination of two elementary combustion modes: homogeneous combustion and flamelet combustion. The combustion index acted as a weighting factor blending the contributions from these two modes. The Chemkin sub-model neglected the subgrid scale turbulence-chemistry interactions whereas the EFTS model took them into account through a presumed PDF approach. The model was used to simulate an early injection mode of a Cummins DI diesel engine and a mode of a Caterpillar DI diesel engine.

The Texas Project was a multi-year study of aftermarket conversions of a variety of light-duty vehicles to CNG or LPG. Emissions and fuel economy when using these fuels are compared to the results for the same vehicles operating on certification gasoline and Federal Phase 1 RFG. Since 1993, 1,040 tests were conducted on 10 models, totally 86 light-duty vehicles. The potential for each vehicle model/kit combination to attain LEV certification was assessed. Also, comparisons of emissions and fuel economy between converted vehicles when operating on gasoline and nominally identical un-converted gasoline control vehicles were analyzed. Additional evaluations were performed for a subfleet that was subjected to exhaust speciations for operation over the Federal Test Procedure cycle and also for off-cycle tests.

This paper describes the results of a comprehensive field-testing program conducted in modern low-emission heavy-duty diesel engines to evaluate the extended oil drain capabilities of several diesel engine oils of varying performance levels. The data generated in the 59-truck trial, which was conducted over a two to three year period, provide support for extension of engine oil drain intervals when a premium mineral diesel oil is used rather than a fighting-grade mineral diesel product. The field trial results also document the performance of a premium fully synthetic engine oil at four times conventional oil drain intervals. Engine inspections conducted after 500,000 test miles confirm that the extension of oil drain intervals with premium diesel engine oils has no negative impact on engine durability.

An electronic particulate matter sensor (EPMS) developed at the University of Texas was used to characterize exhaust gases from a single-cylinder diesel engine and a light-duty diesel vehicle. Measurements were made during transient tip-in events with multiple sensor configurations in the single-cylinder engine. The sensor was operated in two modes: one with the electric field energized, and the other with no electric field present. In each mode, different characteristic signals were produced in response to a tip-in event, highlighting the two primary mechanisms of sensor operation. The sensor responded to both the natural charge of the particulate matter (PM) emitted from the engine, and was also found to create a signal by charging neutral particles. The characteristics of the two mechanisms of operation are discussed as well as their implications on the placement and operation of the sensor.