Search Results

In recognizing the potential for large, damaging impacts from climate change, California enacted Executive Order S-03-05, requiring a reduction in statewide greenhouse gas (GHG) emissions to 80% below 1990 levels by 2050. Given that the transportation light-duty vehicle (LDV) segment accounts for 28% of the state's GHG emissions today, it will be difficult to meet the 2050 goal unless a portfolio of near-zero carbon transportation solutions is pursued. Because it takes decades for a new propulsion system to capture a large fraction of the passenger vehicle market due to vehicle fleet turn-over rates, it is important to accelerate the introduction of these alternatives to ensure markets enter into early commercial volumes (10,000s) between 2015 and 2020. This report summarizes the results and conclusions of a modeling exercise that simulated GHG emissions from the LDV sector to 2050 in California.

The impact of biodiesel and new generation biofuels on emissions from heavy-duty diesel engines was investigated using a California Air Resources Board (CARB) certified diesel fuel as a base fuel. This study was performed on two heavy-duty diesel engines, a 2006 engine and a diesel particle filter (DPF) equipped 2007 engine, on an engine dynamometer over four different test cycles. Emissions from soy-based and animal-based biodiesel, renewable diesel fuel, and gas-to-liquid (GTL) diesel fuel were evaluated at blend levels ranging from 5 to 100%. Consistent with previous studies, particulate matter (PM), hydrocarbons (HC), and carbon monoxide (CO) emissions generally showed increasing reductions with increasing biodiesel and renewable/GTL diesel fuel blend levels for the non-DPF equipped engine. The levels of these reductions were generally comparable to those found in previous studies performed using more typical Federal diesel fuels.

Ethanol fuel is a sustainable energy resource intended to provide a more environmentally and economically friendly alternative to fossil fuels. Ethanol fuel for automotive applications is becoming increasingly widespread and its market is continuing to grow. Measurement of ethanol was traditionally done with an impinger and a gas chromatograph (GC) system but this method is not a direct measurement, usually requires manual handling and takes a long time for post processing of data. The Innova photoacoustic analyzer can directly measure the ethanol emissions in vehicle exhaust without using the impinger/GC system. For the past eight years at Chrysler, the Innova has been used as a stand alone analyzer and the emission sample bags were physically transported to the chemistry lab for ethanol measurement. The data had to be manually entered and post processed for the final results.

In order to demonstrate the performance of a retrofitted selective catalytic reduction (SCR) system while also addressing the issues associated with greater use of biodiesel, a 2005 International 9200i tractor owned by the City of Santa Monica was retrofitted with a titania-vanadia-tungsten catalyst and a urea dosing system supplied by Extengine Systems, Inc. This tractor was operated under normal service conditions within the City of Santa Monica refuse collection and transportation fleet. An on-board emissions measurement system supplied by Engine, Fuel, and Emissions Engineering, Inc. was installed on the vehicle; it measured the emissions and fuel use of the vehicle while it operated on ultra-low-sulfur diesel (ULSD), 20% biodiesel (B20), and 99% biodiesel (B99) on consecutive days.

The Automotive Industry/Government Emissions Research CRADA (AIGER) has been working to develop a new methodology for the direct determination of nonmethane hydrocarbons (DNMHC) in vehicle testing. This new measurement technique avoids the need for subtraction of a separately determined methane value from the total hydrocarbon measurement as is presently required by the Code of Federal Regulations. This paper will cover the historical aspects of the development program, which was initiated in 1993 and concluded in 2002. A fast, gas chromatographic (GC) column technology was selected and developed for the measurement of the nonmethane hydrocarbons directly, without any interference or correction being caused by the co-presence of sample methane. This new methodology chromatographically separates the methane from the nonmethane hydrocarbons, and then measures both the methane and the backflushed, total nonmethane hydrocarbons using standard flame ionization detection (FID).

This paper covers work performed for the California Air Resources Board and US Environmental Protection Agency by Southwest Research Institute. Emission measurements were made on four in-use off-road two-stroke motorcycles and all-terrain vehicles utilizing oxygenated and non-oxygenated fuels. Emission data was produced to augment ARB and EPA's off-road emission inventory. It was intended that this program provide ARB and EPA with emission test results they require for atmospheric modeling. The paper describes the equipment and engines tested, test procedures, emissions sampling methodologies, and emissions analytical techniques. Fuels used in the study are described, along with the emissions characterization results. The fuel effects on exhaust emissions and operation due to ethanol content and fuel components is compared.

Two additive blends proposed for improving the flame luminosity in neat methanol fuel were investigated to determine the effect of these additives on the exhaust emissions in a dual-fueled Volkswagen Jetta. The two blends contained 4 percent toluene plus 2 percent indan in methanol and 5 percent cyclopentene plus 5 percent indan in methanol. Each blend was tested for regulated and unregulated emissions as well as a speciation of the exhaust hydrocarbons resulting from use of each fuel. The vehicle exhaust emissions from these two fuel blends were compared to the Coordinating Research Council Auto-Oil national average gasoline (RF-A), M100, and M85 blended from RF-A. Carter Maximum Incremental Reactivity Factors were applied to the speciated hydrocarbon emission results to determine the potential ozone formation for each fuel. Toxic emissions as defined in the 1990 Clean Air Act were also compared for each fuel.

Gasohol, a blend of 90 percent unleaded gasoline and 10 percent ethanol, has been represented as an alternative to pure gasoline which can reduce the nation’s crude oil dependence. However, a systems analysis of the gasohol production processes indicates that gasohol is increasing rather than decreasing the nation’s dependence on crude oil. Alternative uses of the petroleum and natural gas currently used to manufacture ethanol would reduce the nation’s demand for oil. At the present time, every gallon of crude oil “saved” by substituting ethanol for gasoline results in a need to import approximately two gallons of crude oil. The federal government’s claim that gasohol can reduce the nation’s dependence on imported energy appears, to be based principally on political considerations, but also on the assumption that coal will eventually replace the petroleum and natural gas currently used in the gasohol production wherever possible.

Alternative fuels for internal combustion engines have been the subject of numerous studies. The new U.S. Renewable Fuel Standard has made it a requirement to increase the production of ethanol and advanced biofuels to 36 billion gallons by 2022. Because corn-based ethanol will be capped at 15 billion gallons, 21 billion gallons must come from the advanced biofuels category. A potential source to fill the gap may be butanol and its isomers as they possess fuel properties superior to ethanol. Recently, concerns have been raised about emission of currently non-regulated constituents, aldehydes in particular, from alcohol-based fuels. In an effort to assess the relative impact of the U.S. Renewable Fuel Standards on emissions from a modern gasoline engine, both regulated and non-regulated gas constituents were measured from the combustion of three different alcohol isomers in a modern direct-injected (DI) spark ignition (SI) gasoline engine.

Flexible fuel vehicle production has been steadily increasing in the US over the past fifteen years. Ethanol is considered a renewable fuel additive to gasoline which helps the US efforts in minimizing the dependency on foreign oil. As a result, it is becoming very hard to find pure gasoline which does not contain some ethanol content at the pump in the US. The fuel currently available at the pump contains close to 10% ethanol. The fuel and evaporative systems components and materials on newer flexible fuel vehicles are being designed to be tolerant of the 10% ethanol content. There is a strong desire from ethanol producers to increase the ethanol content up to a 20% level. This is still being debated by the Environmental Protection Agency and a final decision has not been made yet but will be announced by the upcoming Tier 3 Notice of Public Rule Making (NPRM) in December of 2011.

Neat methanol fuel (M100) has many advantages for achieving low emission levels as an automotive fuel, but there are several items that require attention before this fuel can replace conventional fuels. One item involves the low flame luminosity of methanol. An extensive literature search and laboratory evaluation were conducted to identify potential additive candidates to improve the luminosity of a methanol flame. Potential compounds were screened based on their concentration, luminosity improvement, and duration of luminosity improvement during the burn. Three compounds were found to increase the flame luminosity for segments of the burn at relatively low concentrations: toluene, cyclopentene, and indan. In combination, these three compounds markedly improved the luminosity of methanol throughout the majority of the burn. The two combinations were 1) 4 percent toluene plus 2 percent indan and 2) 5 percent cyclopentene plus 5 percent indan in methanol.

Ethanol is widely used as a gasoline component to provide a prescribed amount of oxygenates and for its perceived advantages of less dependence on petroleum based products and lowering overall CO2 emissions. In most cases the level of ethanol in gasoline does not exceed 10%. In some parts of the Unites States, E85 fuel consisting of 85% ethanol and 15% gasoline is commonly available. Many US vehicles sold today are specially adapted for use of both gasoline and high ethanol fuels; so-called Flexible Fuel Vehicles (FFV). While high ethanol fuels are currently a small percentage of the overall gasoline pool, they provide an interesting opportunity to study the effects that ethanol use in gasoline may have on lubricant related performance. Based on past industry experience with methanol based fuel, theoretical areas of concern for ethanol based fuels are valve train rust and potential problems associated with high amounts of water in the lubricant.