Search Results

Accurate numerical prediction of an engine thermal map at a wide range of engine operating conditions can help tune engine performance parameters at an early development stage. This study documents the correlation of an engine thermal simulation using the conjugate heat transfer (CHT) methodology with thermocouple data from an engine operating in a dynamometer and a vehicle drive cell. Three different operating conditions are matched with the simulation data. Temperatures predicted by simulation at specific sections, both at the intake and the exhaust sides of the engine are compared with the measured temperatures in the same location on the operating engine.

Diesel burners introduce combustion of diesel fuel to raise exhaust gas temperature to Diesel Oxidization Catalyst (DOC) light-off or Diesel Particulate Filter (DPF) regeneration conditions, thereby eliminating the need of engine measures such as post-injections. Such diesel combustion requirement nevertheless poses challenges to burner development especially in combustion control and risk mitigation of DPF material failure. In particular, burner design must satisfy good soot distribution and heat distribution at DPF front face after meeting minimum requirements of ignition, heat release, and backpressure. In burner development, Computational Fluid Dynamics (CFD) models have been developed based on commercial codes for burner thermal and flow management with capability of predicting comprehensive physical and chemical phenomena including turbulence induced mixing, fuel injection, fuel droplet transport, diesel combustion, radiation, conjugate heat transfer and etc.

With increasing applications of urea SCR for NOx emission reduction, improving the system performance and durability has become a high priority. A typical urea SCR system includes a urea injector, injector housing, mixer, and appropriate pipe configurations to allow continuous urea injection into the exhaust stream and evaporation of urea solution into gaseous products. Continuous operation at various conditions with high NOx reduction is possible, but one problem that threatens the life and performance of these systems is urea deposit. When urea or its byproducts become deposited on the inner surfaces of the system including walls, mixers, injector housings and substrates it can create concerns of backpressure and material deteriorations. In addition, deposits as a waste of reagents can negatively affect engine operation, emissions performance and DEF economy. Urea deposit behavior is explored in terms of heat transfer, pipe geometry, injector layout and mixing mechanisms.

Due to new federal regulations and higher environmental awareness, the market demands for high fuel economy and low exhaust emission engines are increasing. At the same time customer demands for engine performance, NVH and reliability are also increasing. It is a challenge for engineers to design an engine to meet all requirements with less development time. Currently, the new engine development time has been trimmed in order to introduce more products to the market. Utilizing CAE technology and processes in an engine development cycle can enable engineers to satisfy all requirements in a timely and cost-effectively way. This paper describes a new Powertrain Virtual Analysis Process which has been successfully implemented into Chrysler PTCP (Powertrain Creation Process) and effectively utilized to shorten and improve the product development process. This new virtual analysis process guides the product development from concept through the production validation phases.

This paper describes a comprehensive methodology for the simulation of vehicle body panel buckling in an electrophoretic coat (electro-coat or e-coat) and/or paint oven environment. The simulation couples computational heat transfer analysis and structural analysis. Heat transfer analysis is used to predict temperature distribution throughout a vehicle body in curing ovens. The vehicle body temperature profile from the heat transfer analysis is applied as an input for a structural analysis to predict buckling. This study is focused on the radiant section of the curing ovens. The radiant section of the oven has the largest temperature gradients within the body structure. This methodology couples a fully transient thermal analysis to simulate the structure through the electro-coat and paint curing environments with a structural, buckling analysis.

Computational tools have been extensively applied to predict component temperatures before an actual vehicle is built for testing [1, 2, 3, 4, and 5]. This approach provides an estimate of component temperatures during a specific driving condition. The predicted component temperature is compared against acceptable temperature limits. If violations of the temperature limits are predicted, corrective actions will be applied. These corrective actions may include adding heat shields to the heat source or to the receiving components. Therefore, design changes are implemented based on the simulation results. Sensitivity analysis is the formal technique of determining most influential parameters in a system that affects its performance. Uncertainty analysis is the process of evaluating the deviation of the design from its intended design target.