Search Results

Many experiments have demonstrated that clutch overheating is a major cause of clutch deterioration. Clutch friction material deterioration not only leads to clutch failure, but also causes poor shift quality. Unfortunately, it is not practical to monitor each individual clutch temperature in a production vehicle due to high costs or technical challenges. This paper introduces a proposal for a virtual clutch temperature sensor to monitor the real time clutch temperature changes in Chrysler transmissions with PWM solenoid based control systems. Both vehicle and laboratory dynamometer (dyno) tests demonstrate that the model results match very closely with the thermocouple temperature measurements under many different driving conditions. The real time virtual temperature sensor provides a tool for clutch surface overheat protection and for design improvement and enhancement to shift quality.

In order to define and to optimize a thermal management system for a high voltage vehicular battery, it is essential to understand the environmental factors acting on the battery and their influence on battery life. This paper defines a calendar life aging model for a battery, and applies real world environmental and operating conditions to that model. Charge and usage scenarios are combined with various cooling/heating approaches. This set of scenarios is then applied to the calendar life model, permitting optimization of battery thermal management strategies. Real-world battery life can therefore be maximized, and trade-offs for grid energy conversion efficiency and fuel economy/vehicle range can be determined.

The fuel air ratio imbalance between individual cylinders can result in poor fuel economy and severe exhaust emissions. Individual cylinder fuel air ratio control is one of the important techniques used to improve fuel economy and reduce exhaust emission. California Air Resources Board (CARB) also has required automotive manufacturers to equip with on-board diagnosis system for cylinder fuel air ratio imbalance detection starting in 2011. However, one of the most challenging tasks for the individual cylinder fuel air ratio control and cylinder imbalance diagnosis is how to retrieve the cylinder fuel air ratio information effectively at low cost. This paper presents a novel and practical signal processing based fuel air ratio estimation method for individual cylinder fuel air ratio balance control and on-board fuel air ratio imbalance diagnosis.

This article describes a case study on firmware device management for automotive systems. More specifically it describes the objectives for the project, the methods used, results and conclusions. Objectives: The objective is to create an ecosystem to ensure updates to firmware are fast, reliable, and secure and fault tolerant. To achieve this goal, the most advanced technologies in telematics were combined to produce an automotive solution, including: (1) Bootloader; (2) Delta File; (3) File Compression; (4) Encryption; (5) Re-Flash; (6) Bluetooth® wireless technology; (7) USB; and (8) Flash File Systems technologies. Methods: A pilot project was developed from a case study to understand the complexity of the firmware update problem as it relates to the automotive industry. More specifically, to comprehend the bottlenecks we needed to overcome and to implement the best possible solution. Design and speed performance of the critical path were evaluated.

Two on-line algorithms have been developed to acquire driveline component loads in terms of revolutions at torque and rainflow cycle counting matrix. These algorithms have been implemented in real-time on a standard engine controller unit and have been optimized for fast run-time and low memory requirements. The revolutions at torque algorithm is intended to count the number of driveshaft revolutions in each torque level for each gear and store the number of counts in the engine controller memory. The rainflow cycle counting algorithm is intended to count driveshaft torque cycles and to store the number of counts in a two dimensional “from-to” matrix format in the engine controller memory. The revolutions at torque histogram data and the rainflow cycle counting matrix are then downloaded from the vehicle using the data collection device. Download occurs when the vehicle is serviced at a dealership.

With regard to the use of portable consumer electronic devices in an automobile, Bluetooth has become a widely accepted method for short range wireless communication between a vehicle and a portable device. One Bluetooth connectivity protocol for this use case is Audio/Visual Remote Control Profile (AVRCP). Currently, AVRCP specifies mandatory commands for both target devices (cellular phones and audio players), as well as for control devices like an audio head unit. However, there is no requirement that control devices and target devices implement the same commands, nor is there a requirement that supported commands utilize information that would be useful in improving the driver's experience (i.e. metadata). This paper will describe the impact of this reality from the perspective of the automotive consumer, and propose an “automotive grade” AVRCP that could provide a more consistent consumer experience in the automotive market.

Strain gages have been widely used for measuring strain or deformation. They are very reliable and accurate. However, for application on fabric material, strain gages have their limitations. In this paper, digital image correlation (DIC) is used to measure the deformation around the rear window on a convertible top. The test needed to be non destructive, the vehicle and convertible top could not be damaged. The deformation or strain measured on the fabric was used to estimate the force experienced at the interface between the glass and the fabric during an opening/closing application. A speckle pattern was created on the convertible fabric where deformation was to be measured with washable paint. The image of the measured area was first recorded. The convertible top was then latched down and the fabric was stretched. A second image was recorded again. Based on the two images, the deformation/strain between the two conditions was measured.

This paper presents a parametric study of two semiactive adaptive control algorithms through simulation: the non-model based skyhook control, and the newly developed model-based nonlinear adaptive vibration control. This study includes discussion of suspension model setup, dynamic analysis approach, and controller tuning. The simulation setup is from a heavy-duty truck seat suspension with a magneto-rheological (MR) damper. The dynamic analysis is performed in the time domain using sine sweep excitations without the need to linearize such a nonlinear semiactive system that is studied here. Through simulation, the effectiveness of both control algorithms is demonstrated for vibration isolation. The computation flops of the simulation in the SIMULINK environment are compared, and the adaptability is studied with respect to plant variations and different excitation profiles, both of which come across typically for vehicle suspension systems.

This paper describes the simulation of a bi-tensional (14 Volt/42 Volt) hybrid vehicle. The focus is on gaining a better understanding of vehicle sub-system interactions through simulation. Sensitivity to assumptions on the simulated performance of the vehicle is examined. Variations in the simulation will focus on energy storage, power generation, motoring, and load management. Optimization of system interactions, relative to the desired vehicle performance and function, are considered in the conclusion.

A new method to simulate “the FM radio reception on the road” in an open space is proposed. It can provide reliable and objective evaluation of the radio system including a vehicle. It can reduce the cost and time of the driving test on roads. It is based on two technologies. One is a wave-extraction system of incoming waves on the roads and the other the field reconstruction in an open space. For the extraction, 3-D software based on AIC is developed and can estimate the number of waves and the amplitude, phase and polarization of the waves from the field data. The software showed the extraction accuracy of 90% in simulation. This method was applied to the road test, and it was found that the software could extract the waves. And through several tests in the space, the feasibility of the reconstruction of standing wave was confirmed (Maximum-minimum ratio: 18 dB and 22 dB at FM-band for the horizontal and the vertical polarization).

The rapid growth of electronic feature content within the vehicle continues to challenge the automotive industry. Customers want cutting edge consumer electronics features in a vehicle before the features are obsolete. However, automotive manufacturers continue to struggle with introducing new features into vehicles before they become obsolete to the customer. The ability for automotive manufacturers to seamlessly upgrade existing products with new and improved products continues to plague the automotive industry. Vehicles traditionally take 4 plus years to design and manufacture. Automotive manufacturers need to plan consumer electronics features early, but not actually integrate those into the vehicle until late in the design cycle, possibly on the production line. This would help facilitate providing the most recent features.

This paper discusses steps for identifying, evaluating and recommending a quantifiable design metric or metrics for Side Airbag (SAB) development. Three functionally related and desirable attributes of a SAB are assumed at the onset, namely, effective SAB coverage, load distribution and efficient energy management at a controlled force level. The third attribute however contradicts the “banana shaped” force-displacement response that characterizes the ineffective energy management reality of most production SAB. In this study, an estimated ATD to SAB interaction energy is used to size and recommend desired force-deformation characteristic of a robust energy management SAB. The study was conducted in the following three phases and corresponding objectives: Phase 1 is a SAB assessment metric identification and estimation, using a uniform block attached to a horizontal impact machine.

This paper is the second in the series of documents designed to record the progress of a series of SAE documents - SAE J2836™, J2847, J2931, & J2953 - within the Plug-In Electric Vehicle (PEV) Communication Task Force. This follows the initial paper number 2010-01-0837, and continues with the test and modeling of the various PLC types for utility programs described in J2836/1™ & J2847/1. This also extends the communication to an off-board charger, described in J2836/2™ & J2847/2 and includes reverse energy flow described in J2836/3™ and J2847/3. The initial versions of J2836/1™ and J2847/1 were published early 2010. J2847/1 has now been re-opened to include updates from comments from the National Institute of Standards Technology (NIST) Smart Grid Interoperability Panel (SGIP), Smart Grid Architectural Committee (SGAC) and Cyber Security Working Group committee (SCWG).

New vehicle systems that stop and restart the engine to avoid prolonged idling place new requirements on audio systems. In particular, there is a need for the audio system to continue to operate during the engine start sequence. In the past this was not an issue, as audio systems could be turned off during the engine start sequence. Among the ramifications for this “operate while starting” requirement is that the audio system must operate at a lower voltage, say 6 volts, instead of 10 volts. Audio system operation in this context means continuing to play music without interruption or spurious noises. The main focus of this presentation is on audio circuits, both line-level and speaker level. In the past, line level outputs could be fed by linear regulated power supplies that developed 8 to 10 volts. The signal levels sent from one module to another could thus be in the 3 volt RMS range.

This paper presents a process for the selection of spring rate and pre-load for an adaptively controlled pivoting vane oil pump. The pivoting vane pump has two modes: high and low speed. A spring within the pump is installed to induce a torque that causes an adaptive displacement mechanism within the pump to move toward maximum oil chamber size. In low speed mode, two feedback regions are pressurized that produce torques that counter the spring generated torque. Together, both regions being pressurized by main oil gallery pressure tend to reduce pump displacement more at lower speeds than if only a single chamber is pressurized. At higher speeds, a solenoid switch turns off pressure to one of the feedback pressure chambers, thereby reducing feedback torque that counters spring torque. This enables higher pressure calibrations in this speed mode. In this paper, we identify a process for choosing the spring rate and pre-load that calibrates the adaptive displacement mechanism.

The common practice in finite element based fatigue calculation with multiple channels of road load is to perform a set of unit load static stress analysis and conduct stress time history construction later during fatigue calculation. The main advantage of this so-called quasi-static finite element based fatigue calculation is to avoid time-consuming dynamic stress analysis and also reduce static stress analysis from millions of real load cases to a few dozens unit-load cases. The main disadvantage of this quasi-static finite element based fatigue calculation is the absence of vibration-induced stresses in stress time history construction and fatigue analysis. A decade ago, a modal transient finite element based fatigue calculation was proposed to introduce vibration-induced stresses into finite element based fatigue calculation. The idea is to add vibration-induced modal stresses to load-induced instant stresses in stress time history construction and fatigue calculation.

The concept of full vehicle simulation has been embraced by the automobile industry as it is an indispensable tool for analyzing vehicles. Vehicle loads traditionally obtained by road load data acquisition such as wheel forces are typically not invariant as they depend on the vehicle that was used for the measurement. Alternatively, virtual road load data acquisition approach has been adopted in industry to derive invariant loads. Analytical loads prior to building hardware prototypes can shorten development cycles and save costs associated with data acquisition. The approach described herein estimate realistic component load histories with sufficient accuracy and reasonable effort using full vehicle simulations. In this study, a multi-body dynamic model of the vehicle was built and simulated over digitized road using ADAMS software, and output responses were correlated to a physical vehicle that was driven on the same road.

Due to their high energy density and low self-discharge rates, lithium-ion batteries are becoming the favored solution for portable electronic devices and electric vehicles. Lithium-Ion batteries require special charging methods that must conform to the battery cells' power limits. Many different charging methods are currently used, some of these methods yield shorter charging times while others yield more charge capacity. This paper compares the constant-current constant-voltage charging method against the time pulsed charging method. Charge capacity, charge time, and cell temperature variations are contrasted. The results allow designers to choose between these two methods and select their parameters to meet the charging needs of various applications.

There is a continual need to apply heat treatment processes in innovative ways to optimize material performance. One such application studied in this research is carburizing followed by austempering of low carbon alloy steels, AISI 8620, AISI 8822 and AISI 4320, to produce components with high strength and toughness. This heat treatment process was applied in two steps; first, carburization of the surface of the parts, second, the samples were quenched from austenitic temperature at a rate fast enough to avoid the formation of ferrite or pearlite and then held at a temperature just above the martensite starting temperature to partially or fully form bainite. Any austenite which was not transformed during austempering, upon further cooling formed martensite or was present as retained austenite.

There is a growing worldwide concern regarding the environmental aspects related to the performance of a corporation and its products, whether by consumer demand or government requirements. The constant pressure for innovations and improvements related to sustainable development are current issues in everyday life of any institution that seeks to consolidate a position of acceptance and competitiveness in the global market. The automotive industry is one of the markets more involved and challenged to the demand of the environmental requirements in regards the limits of pollutant emissions and consequently fuel consumption. The European and North America vehicles already have more electrical content inside (either related to safety and comfort or even needs related to weather), which results in significantly higher consumption levels than traditionally observed in Brazil's application.