Search Results

The simulation of heat exchanger air flow characteristics in a sub-scale wind tunnel test requires an accurate representation of the full-scale pressure drop across the element. In practice this is normally achieved using laminations of various porous materials and honeycombs on the basis of experience and ad hoc data. In view of this, a series of measurements of the pressure drop, in both the near and far field, across screens with porosity (β) in the range 0.41 ≺ β ≺ 0.76 are reported. The aim being to establish a relationship between the porosity and the pressure drop characteristics of a given material at various angles of inclination to the free-stream flow. Furthermore, the effect of screen depth was investigated using honeycombs. This data will facilitate detailed design and accurate representation of the flow characteristics at sub scale.

The interactions between automatic controls, physics, and driver is an important step towards highly automated driving. This study investigates the dynamical interactions between human-selected driving modes, vehicle controller and physical plant parameters, to determine how to optimally adapt powertrain control to different human-like driving requirements. A cyber-physical system (CPS) based framework is proposed for co-design optimization of the physical plant parameters and controller variables for an electric powertrain, in view of vehicle’s dynamic performance, ride comfort, and energy efficiency under different driving modes. System structure, performance requirements and constraints, optimization goals and methodology are investigated. Intelligent powertrain control algorithms are synthesized for three driving modes, namely sport, eco, and normal modes, with appropriate protocol selections. The performance exploration methodology is presented.

The quantitative assessment and comparison of different hybrid vehicle options has traditionally been done on the basis of measuring or estimating the vehicle's fuel economy over predefined drive-cycles. In general, little or no consideration has been given to the more subjective and difficult to quantify vehicle requirements, such as trying to understand which derivative will be the most “fun” vehicle to drive. A lack of understanding in this area of vehicle performance sufficiently early within the development life-cycle so as to be in a position to influence the vehicle design, can lead to a compromised powertrain architecture which will ultimately increase the risk of product failure. The work presented within this paper constitutes part of the overall design activities associated with the LIFECar programme. The aim of the LIFECar consortium is to manufacture a lightweight, fuel cell hybrid electric sports vehicle.

This paper gives an overview of the development of a number of loss models for the pushing metal V-belt CVT. These were validated using a range of experimental data collected from two test rigs. There are several contributions to the torque losses and new models have been developed that are based upon relative motion between belt components and pulley deflections. Belt slip models will be proposed based upon published theory, expanded to take account of new findings from this work. The paper introduces a number of proposals to improve the efficiency of the transmission based on redesign of the belt geometry and other techniques to reduce frictional losses between components. These proposed efficiency improvements have been modelled and substituted into a complete vehicle simulation to show improvements in vehicle fuel economy over a standard European drive cycle.

In automotive aerodynamics much use has been made of generic reference models for research and correlation. Research work has been conducted mostly on small-scale versions of the models to investigate flow regimes and aerodynamic force and moment characteristics while correlation tests have made use of full-scale models to compare results between wind tunnels. More recently reference geometries have also been used as test cases in the validation of computational techniques. This paper reviews the design characteristics and use of several key reference models. The advantages and disadvantages of these designs and also the applicability of the results in providing guidelines for the development of production vehicles are discussed. It is advocated that when researchers choose to use simple models, existing reference geometries should be employed.

Cooling drag, typically known as the difference in drag coefficient between open and closed cooling configurations, has traditionally proven to be a difficult flow phenomenon to predict using computational fluid dynamics. It was seen as an academic yardstick before the advent of grille shutter systems. However, their introduction has increased the need to accurately predict the drag of a vehicle in a variety of different cooling configurations during vehicle development. This currently represents one of the greatest predictive challenges to the automotive industry due to being the net effect of many flow field changes around the vehicle. A comprehensive study is presented in the paper to discuss the notion of defining cooling drag as a number and to explore its effect on three automotive models with different cooling drag deltas using the commercial CFD solvers; STARCCM+ and Exa PowerFLOW.

Simulations are presented which fully couple both the aerodynamics and cooling flow for a model of a fully engineered production saloon car (Jaguar XJ) with a two-tier cooling pack. This allows for the investigation of the overall aerodynamic impact of the under-hood cooling flow, which is difficult to predict experimentally. The simulations use a 100 million-element mesh, surface wrapped and solved to convergence using a commercially available RANS solver (STARCCM+). The methodology employs representative boundary conditions, such as rotating wheels and a moving ground plane. A review is provided of the effect of cooling flows on the vehicle aerodynamics, compared to published data, which suggest cooling flow accounts for 26 drag counts (0.026 Cd). Further, a sensitivity analysis of the pressure drop curves used in the porous media model of the heat exchangers is made, allowing for an initial understanding of the effect on the overall aerodynamics.

Water is always present in jet fuel, usually in a mixture of forms. At very low temperatures this phenomenon can lead to the formation of ice crystals within the aircraft fuel system, which can then stay in suspension within the entire volume of fuel. Pumps within the fuel system transfer fuel around the system. Pumps such as boost pumps that are typically used in fuel systems are protected by a weave type filter mesh at the inlet. Ice accretion on the surface of this mesh has operational implications as it can cause non optimal fuel flow. In this investigation, two fundamental tools are being used: 1) a high fidelity MATLAB model of a mesh strainer, pick-up line and pump, and 2) a test rig of the modelled system. The model is being used to investigate fuel system performance when exposed to fuel containing water/ice contaminants at cold temperatures.

A modern benchmark for passenger cars - DrivAer model - has provided significant contributions to aerodynamics-related topics in automotive engineering, where three categories of passenger cars have been successfully represented. However, a reference model for high-performance car configurations has not been considered appropriately yet. Technical knowledge in motorsport is also restricted due to competitiveness in performance, reputation and commercial gains. The consequence is a shortage of open-access material to be used as technical references for either motorsport community or academic research purposes. In this paper, a parametric assessment of race car aerodynamic devices are presented into four groups of studies. These are: (i) forebody strakes (dive planes), (ii) front bumper splitter, (iii) rear-end spoiler, and (iv) underbody diffuser.

In this paper, gear ratios of a two-speed transmission system are optimized for an electric passenger car. Quasi static system models, including the vehicle model, the motor, the battery, the transmission system, and drive cycles are established in MATLAB/Simulink at first. Specifically, since the regenerative braking capability of the motor is affected by the SoC of battery and motors torque limitation in real time, the dynamical variation of the regenerative brake efficiency is considered in this study. To obtain the optimal gear ratios, iterations are carried out through Nelder-Mead algorithm under constraints in MATLAB/Simulink. During the optimization process, the motor efficiency is observed along with the drive cycle, and the gear shift strategy is determined based on the vehicle velocity and acceleration demand. Simulation results show that the electric motor works in a relative high efficiency range during the whole drive cycle.

The effect of local fuel concentration on cyclic variability in combustion and engine performance in a lean burn stratified charge engine has been investigated. The fuel concentration in a plane close to the spark plug was measured for a large number of cycles using laser-induced fluorescence (LIF) and simultaneous measurement of in-cylinder pressure in an one-cylinder optical research engine. It could be shown quantitatively that the fuel concentration in a small region close to the spark plug has a dominating effect on the subsequent pressure development for lean mixtures. Variations in the mixture concentration in the vicinity of the spark plug contribute significantly to cyclic variation in combustion. Measurement of the flame area in the same plane 20 °CA after ignition revealed that the direction of growth of the established flame is not significantly influenced by the stoichiometry.

A mild hybrid powertrain with crankshaft mounted integrated motor generator (IMG) and torque controlled infinitely variable transmission (IVT) has shown clear potential for fuel economy (FE) enhancement. It also makes significant driveability and performance improvements possible which are a condition for customer satisfaction and subsequent marketability. The hybrid powertrain supervisory control strategy presented here uses the energy recovered during braking events for power assist, hence improving FE and driveability compromises. This is achieved by operating the engine at its best brake specific fuel consumption (BSFC) point during steady state conditions without deteriorating the transient response as a result of the comparatively fast IMG torque response. This paper demonstrates the launch manoeuvre and general driveability improvements achieved in simulation with validated models.

Current modelling capability for engine icing accretion prediction is still limited for App. C. To further validate icing codes in complex engine geometries, it is necessary to perform additional experimental work in relevant geometrical and environmental conditions. Within the frame of ICE GENESIS [1], an experiment has been setup to replicate the condition at the inlet of an engine first stage compressor. This paper describes the choices for the design of the engine compressor model, the setup within the icing wind tunnel and the methodology employed to obtain the results. Additionally, more effort has been focused on obtaining accurate ice shapes using a 3D scanning system. Results of 3D scans are given.

The aerodynamic drag of future low emission vehicles will need to be low. Unfortunately, vehicle shapes that result in low drag coefficients - of the order of 0.15 - are often aerodynamically unstable in crosswinds. The addition of wheels, transmission, radiators, suspension, steering, brakes, air ducts and wing mirrors can easily increase this drag coefficient to 0.24 and above and produce an undesirable lift distribution. The Aero-Stable Carbon Car (ASCC) is a research project, in conjunction with industrial partners, to design and build a practical 3 to 4 seat low drag car (CD less than 0.20) with an acceptable lift distribution (front to rear) which is also stable in crosswinds and in yaw through a series of low speed wind tunnel tests performed in the Cranfield College of Aeronautics 8′ × 6′ wind tunnel facility.

The simulation of natural-like snow conditions in a controlled environment such as an Icing Wind Tunnel (IWT) is a key component for safe, efficient and cost-effective design and certification of future aircraft and rotorcraft. Current capabilities do not sufficiently match the properties of natural snow, especially in terms of size and morphology. Within the Horizon 2020 project ICE GENESIS, a new technology has been developed aiming to better recreate natural snowflakes. The focus of the newly developed system was the generation of falling snow in a temperature range of +1°C to -4°C. Ground measurements and flight test campaigns have been performed to better characterize these conditions and provide requirements for wind tunnel facilities. The calibration results of the new snow generation system as well as snow accretion data on a NACA0012 test article with a chord length of 0.377 m are presented.

The present work focuses on developing an integrated airframe, distributed propulsion, and power management methodology for liquid-hydrogen-fuelled HALE UAVs. Differently from previous studies, the aim is to assess how the synergies between the aforementioned sub-systems affect the integrated system power requirement, production, and distribution. A design space exploration study was carried out to assess the influence of distributing motor-driven fans on three different airframes, namely a tube-and-wing, a triple-fuselage, and a blended-wing-body. For the considered range of take-off masses from 5,000 to 15,000 kg, the 200 kW payload power requirement under examination was found to re-shape the endurance trends. In fact, the drop in specific fuel consumption due to the engine design point change alters the trends from nearly flat to a 25% maximum endurance increase when moving towards heavier take-off masses.

This paper focuses on the investigation of the nature, process and effects of ice accretion on different feed pump strainers upstream of the aircraft feeding system. A suitable test rig was designed to circulate Jet A-1 containing water/ice contaminants at cold temperatures through the strainers. Following an extensive literature review, a number of screening tests were performed. These provided a strong base for an exhaustive study of fuel icing in the dynamic environment offered by the test rig. The effects of the rate of fuel cooling on the nature of ice were examined. As expected, it was observed that the yield of ice generated on the mesh screen increased with the water concentration in the fuel. It was also revealed that at higher cooling rates, a crust of snow formed on top of softer ice on the mesh screen.

A 3D Navier-Stokes CFD model of a wheel located within a wheelhouse cavity has been produced. Both a stationary wheel on a fixed ground and a rotating wheel on a moving ground were considered. Extensive comparisons with the results of a wind tunnel investigation based on the same geometry are presented. These consist of three force coefficients and pressures on the internal faces of the cavity. Comparison with the experimental results gave encouraging agreement. It was found that the rotating wheel produced more drag than the stationary wheel whilst shroud drag decreased when the groundplane was moving compared to when it was stationary.

This study aims to provide an understanding of self-similarity in the turbulent wake generated by a Fastback DrivAer automotive model and assess the impact of upstream disturbances on the wake. The disturbances are generated using a circular cylinder placed five cylinder diameters upstream. Multiple ‘cylinder-model’ positions were tested by offsetting the lateral positioning of the cylinder with respect to the centreline of the model. Data was obtained at cross-planes in the wake going from 25% to 100% car length. Wind tunnel data has been obtained using a total pressure probe rake and a four-hole cobra probe. Data has also been obtained using RANS based simulations with k – ε realisable turbulence model. Mean axial-component velocity profiles were analysed with momentum thickness (θ) and vorticity thickness (δω) used as the scaling parameters. It was seen that self-similarity marginally exists in the wake depending on the upstream conditions and the scaling parameter.

The rise of autonomous technologies may reflect on new vehicle traffic characteristics, likely reducing vehicle-to-vehicle proximity and emerging platooning formations. Energy consumption, stability, and surface contamination are relevant factors that are sensitive to aerodynamic interference while platooning. From the experimental perspective, most wind tunnels were originally designed to host isolated models, and these constraints often limit the investigation of multiple full-body vehicle formations (e.g. test section length, moving ground dimensions, standard testing points). This paper introduces the ‘MultiWake’ model - a parametric bluff-body device based on a morphing concept, which can emulate the aerodynamic wake characteristics of different vehicle classes.