Search Results

A cooling fan is one of the primary components affecting the cooling performance of an engine cooling system. In recent years, with the increase in electric vehicles (EVs) and hybrid vehicles (HVs), the cooling performance and noise level of the cooling fan have become very important. Thus, the development of a low-noise fan with the same cooling performance is urgently required. To address this issue, it is critical to find the relation between the performance of the fan and the flow structures generated around it, which is discussed in the present paper. Specifically, a computational method is employed that uses unsteady Reynolds-averaged Navier-Stokes (URANS) coupling with a sliding mesh (SLM). Measurements of the P-Q (Pressure gain-Flow rate) characteristics are performed to validate the predictive accuracy of the simulation.

This paper presents two newly developed technologies of optimizing impurity diffusion concentration for silicon semiconductor material and controlling internal stress of the top SiN (Silicon Nitride) layer on a membrane of a silicon substrate to apply them to the manufacturing process of MEMS (Micro Electro Mechanical Systems) type air-flow sensor chips. Until today, in MEMS-type airflow sensors, poly-crystalline silicon (poly-Si) and platinum were widely used as a resistor material of key functional elements on a membrane of air-flow-rate measurement portion. The functional resistors on the membrane are required to monitor high temperatures of about 300 °C and to perform the self-heating operations at that temperature range because of the suppression of contaminant deposition by means of evaporation or incineration.

Higher pressure and higher precision are required for diesel fuel injection equipment in response to increasingly severe emissions control regulations. Market diesel fuels have become more diversified than in the past. Diesel fuel quality has also been changing, being affected by crude oil slate, extreme lowering of sulfur content, and diesel reformulated from heavy fuel oil, among other reasons. As a result of this, deposits thought to have a fuel origin have been observed within diesel fuel injectors in certain regions. Related changes in fuel injection quantity have also been observed. This paper determines injector deposit production mechanisms. It focuses on the structural changes of deposit causative substances by temperature as well as injector design change improvements to prevent deposits.

Down-sizing and dielectric insulation were required for the traction motors of hybrid vehicles. By utilizing the newly developed coil with thick resin insulation atop the conventional enamel film, the use of conventional inter-phase insulation paper was abolished. Furthermore, by adopting the stair-shaped coil structure and spiral winding configuration, the stator size was minimized. With the above technologies, the motor installation to smaller hybrid vehicles was realized, thus contributing to weight reduction of hybrid vehicles.

Heat exchangers used as charge air coolers are repeatedly subjected to thermal strain, which may cause fracture. To predict the durability of heat exchangers, stress estimations using Finite Element Analysis (FEA) are effective. However, producing a detailed finite element model would require an enormous number of elements and excessive calculation costs. To resolve this problem, we focused on periodic tube-fin structures, considering actual and designed fin shapes, and applied a homogenization method to the fins. We then determined their homogenization elastic stiffness and verified it by conducting compression experiments and analyses using partial models consisting of laminated tube-fin structures. If fins are homogenized, it is important that homogenization be based on the actual fin shape. We then produced a finite element model of a charge air cooler assembly by using the homogenization element, and conducted analyses which simulated a thermal fatigue test.

In order to improve corrosion resistance and thermal efficiency of the air conditioner evaporator, a coating which provides hydrophilicity was formed over the chromate coating. In addition, there has been greater demand for air with fewer smells. This report describes the cause of “dusty odor” and a method to reduce it. The dusty odor is caused by a little corrosion of the substrate aluminum. Hydrophilic coating film dissolves little by little in condensed water, and substrate aluminum is exposed. A method to prevent the odor was developed by forming a coating giving hydrophilicity and durability to the evaporator surface.

The development of a multicolor electro-luminescent (EL) display for instrument cluster which emits red, green and their mixed colors is presented in this paper. We constructed the EL display with a stacked panel configuration, which is composed of a lower panel of the green ZnS:Tb luminescent layer and an upper one of the red ZnS:Mn + filter luminescent layer. The display is based on three technologies. First, green luminance of the ZnS:Tb was improved by appropriately arranging the crystal environment around the Tb luminescent center. Second, a suitable red filter was developed to obtain red light by filtering ZnS:Mn. Last, a process to fabricate transparent EL panels was established. This technology allows the green panel to be located on the lower side of the red panel. As a result of these developments, the luminance of the display has been increased to a comfortable level.

As the demand for improved fuel economy increases and new CO2 regulations have been issued, aerodynamic drag reduction has become more critical. One of the important factors to consider is cooling drag. One way to reduce cooling drag is to decrease the air flow volume through the front grille, but this has an undesirable impact on cooling performance as well as component heat load in the under-hood area. For this reason, cooling drag reduction methods while keeping reliability, cooling performance and component heat management were investigated in this study. At first, air flow volume reduction at high speed was studied, where aerodynamic drag has the greatest influence. For vehicles sold in the USA, cooling specification tends to be determined based on low speed, while towing or driving up mountain roads, and therefore, there may be extra cooling capacity under high speed conditions.

Requirements for fuel economy improvement and reduction in the vehicles engine compartment have increased significantly in the pass years. Performances in radiators have driven changes in terms of compactness and weight reductions. By focusing on the air flow we have optimized the radiator fin and developed a high performance radiator. A similar performance was achieved using an 11mm core depth which has 30% weight reduction compared to a 16mm core depth. The purpose of this paper is to present a technical outline about fin optimization.

This study investigates the reduction of the Blade Passing Frequency (BPF) noise radiated from an automotive engine cooling fans, especially in case of the fan with an eccentric shroud. In recent years, with the increase of HV and EV, noise reduction demand been increased. Therefore it is necessary to reduce engine cooling fan noise. In addition, as a vehicle trend, engine rooms have diminished due to expansion of passenger rooms. As a result, since the space for engine cooling fans need to be small. In this situation, shroud shapes have become complicated and non-axial symmetric (eccentric). Generally, the noise of fan with an eccentric shroud becomes worse especially for BPF noise. So it is necessary to reduce the fan BPF noise. The purposes of this paper is to find sound sources of the BPF noise by measuring sound intensity and to analyze the flow structure around the blade by Computational Fluid Dynamics (CFD).

In electronic products, the recently increasing thermal radiation demands higher thermal conductivity of polymer composites. However, inaccurate observation of the filler dispersion within the polymer does not allow for accurate quantification of Interface Thermal Resistance and subsequently the prediction of thermal conductivity. Therefore, optimum filler design could not be achieved. Firstly in this report, accurate stereoscopic filler dispersion was observed by FIB-SEM. Secondly, quantification of Interface Thermal Resistance could be achieved by thermal conduction analysis using filler dispersion model. Thirdly, this Interface Thermal Resistance enabled the prediction of the thermal bulk conductivity. Lastly, the prediction made above could be validated by comparison of predicted value to measured value. This result may lead to optimum filler design and thereby to the development of higher thermal radiation materials.

The demand for better driving comfort, fuel efficiency and reduced CO2 output has been becoming increasingly stringent. In response to such needs, we developed Transmission Electro-Hydraulic Control Module (TEHCM). For Automatic Transmission, expanding the lock-up control area is necessary to improve fuel efficiency. Meanwhile, lock-up control at lower speeds aggravates shift quality. To improve shift quality, Automatic Transmission Fluid (ATF) pressure control must be precise is needed. This can be accomplished by compensating for deviation in TEHCM, which integrates Transmission Control Unit (TCU) and the pressure control actuator, Variable Force Solenoid (VFS). However, there are two problems in installing TEHCM in compact vehicle. The first problem is the miniaturization of such TEHCM. Regarding modules that require a high electrical current to operate the VFS, thermal conductivity contradicts miniaturization.