Search Results

A detailed study is undertaken to examine how 2010+ diesel engine exhaust emissions change when a soybean-derived B20 biodiesel fuel is used instead of a conventional ultra-low sulfur diesel fuel and to investigate how these changes impact the aftertreatment system. Particulate matter (PM) emissions for each fuel are characterized in terms of mass emissions, size distributions, organic versus soot fraction, metals content, and particle morphology. PM mass recorded by Dekati Mass Monitor, thermal analysis of quartz filters, and calculated from particle size distributions consistently shows a 2 - 3 fold decrease in engine-out soot emissions over a wide mid-load range when changing from ULSD to B20 fuel. This is partly due to a decrease in particle number and partly to a decrease in average size. HC and NO emissions, in contrast, exhibit little change with fuel type.

An experimental study is performed to investigate the effects of charge motion control on in-cylinder fuel-air mixture preparation and combustion inside a direct-injection spark-ignition engine with optical access to the cylinder. High-pressure production injector is used with fuel pressures of 5 and 10 MPa. Three different geometries of charge motion control (CMC) device are considered; two are expected to enhance the swirl motion inside the engine cylinder whereas the third one is expected to enhance the tumble motion. Experiments are performed at 1500 rpm engine speed with the variation in fuel injection timing, fuel pressure and the number of injections. It is found that swirl-type CMC devices significantly enhance the fuel-air mixing inside the engine cylinder with slower spray tip penetration than that of the baseline case without CMC device. Combustion images show that the flame growth is faster with CMC device compared to the similar case without CMC device.

Effects of changing ambient humidity and temperature have been studied on the performance and emissions of a hand-held two-stroke and a hand-held four-stroke engine. The main effect of changes in ambient conditions is to change the intake air density and therefore the air-fuel ratio metered by the carburetor. Trends in the effects of humidity and temperature on emissions are predicted reasonably well by theoretical thermodynamic models. They suggest an improved correction for the dependence of NOx on ambient conditions, as a function of both humidity and operational air-fuel ratio, which appears to collapse NOx production data better than the existing KH correction factor. They also suggest a simple procedure for tuning engines to design air-fuel ratios using the measured exhaust-gas %CO, which takes into account the prevailing ambient conditions.

In the design of small off-highway and utility engines for compliance with increasingly stringent emissions standards, one component which can potentially reduce engine exhaust-gas emissions without necessitating changes in other, more costly parts is the spark plug. From studies carried out in automobile engines, benefits have been reported when using different spark-plug electrode shapes or when aligning the plugs in the cylinder head in preferred directions. However, these benefits, observed in automotive overhead valve engines with well-mixed charges, have generally been modest? and spark plugs of conventional shape remain the most widely used today. In the case of off-highway and utility engines, which operate at substantially higher air-fuel ratios, often with poorly-mixed charges, the potential for improving performance by changing spark-plug shape has not been explored.

All modern automotive automatic transmissions require the use of a torque converter to allow for the transmission of torque from the engine to the drivetrain. Although they are commonly used throughout the automotive industry, there is little understanding of the internal flows within the torque converter. An experimental study has been conducted to reveal the internal flow characteristics within a production torque converter using Laser Doppler Velocimetry (LDV) under the operating conditions. LDV measurements were conducted on the planes between impeller blades, and the gap between the impeller and turbine blades. The study showed that the internal flow is highly complex and the difference in rotor speeds between the impeller and turbine compound the flow effects. Transmission oil flows in the planes at the impeller exit and gap region were affected by the turbine blade as it passed.

This paper reviews progress on turbulent jet ignition systems for otherwise standard spark ignition engines, with focus on small prechamber systems (≺3% of clearance volume) with auxiliary pre-chamber fueling. The review covers a range of systems including early designs such as those by Gussak and Oppenheim and more recent designs proposed by General Motors Corporation, FEV, Bosch and MAHLE Powertrain. A major advantage of jet ignition systems is that they enable very fast burn rates due to the ignition system producing multiple, distributed ignition sites, which consume the main charge rapidly and with minimal combustion variability. The locally distributed ignition sites allow for increased levels of dilution (lean burn/EGR) when compared to conventional spark ignition combustion. Dilution levels are comparable to those reported in recent homogeneous charge compression ignition (HCCI) systems.

Many engineering systems create unwanted noise that can be reduced by the careful application of engineering noise controls. When this noise travels down tubes and pipes, a tuned resonator can be used to muffle noise escaping from the tube. The classical examples are automobile exhaust and ventilation system noise. In these cases where a narrow frequency band of noise exists, a traditional engineering control consists of adding a tuned Helmholtz resonator to reduce unwanted tonal noise by reflecting it back to the source (Temkin, 1981). As long as the frequency of the unwanted noise falls within the tuned resonator frequency range, the device is effective. However, if the frequency of the unwanted sound changes to a frequency that does not match the tuned resonator frequency, the device is no longer effective. Conventional resonators have fixed tuning and cannot effectively muffle tonal noise with time-varying frequency.

The Environmental Protection Agency (EPA) is developing emission standards for nonroad spark-ignition engines rated over 19 kW. Existing emission standards adopted by the California Air Resources Board for these engines were derived from emission testing with new engines, with an approximate adjustment applied to take deterioration into account. This paper describes subsequent testing with two LPG-fueled engines that had accumulated several thousand hours of operation with closed-loop control and three-way catalysts. These engines were removed from forklift trucks for characterization and optimization of emission levels. Emissions were measured over a wide range of steady-state points and several transient duty cycles. Optimized emission levels from the aged systems were generally below 1.5 g/hp-hr THC+NOx and 10 g/hp-hr CO.

A stratified charge research engine and test stand were designed and built for this work. The engine was designed to exhibit some of the desirable traits of both the premixed charge gasoline engine and modern diesel engine. This spark ignition engine is fueled by M100 (99.99% pure methanol), operates under high compression (19.3:1) and uses direct fuel injection to form a stratification of the fuel-air mixture in the cylinder. The beginning of the combustion event of the stratified mixture is triggered by spark plug discharge. The primary goal of this project was to evaluate the feasibility of using a removable integral injector ignition source insert, which allows a convenient method of changing the relative location of the fuel injector to the ignition source, as well as the compression ratio, squish height, and bowl volumes. This paper provides an explanation of the hardware included in the experimental setup of the engine and selection of the direct injector configuration.

The purpose of this work was to develop a fiber optic imaging system for use in flow visualization studies at the Michigan State University Engine Research Laboratory. A flexible fiber optic image carrier was coupled with a high speed rotating prism camera to create a unique imaging system which can easily reach remote location test sites. The flow visualization study was conducted on a motored 3.5 L four-valve engine test rig. A 40 watt pulsed copper vapor laser was synchronized with the camera to produce motion picture film at 5000 frames per second (fps). The image carrier which is attached to the camera contained an 80 degree field of view (FOV) tip adapter for viewing the entire cross-sectional area of the cylinder. The area imaged was a radial plane located 3 cm from the intake valves. The engine rig was motored at 850 rpm with a flow rate of 18 kg/hr. Entrained microballoon seeding particles were filmed as they traveled through the cylinder.

Of all existing modes of transportation, onroad motor vehicles are the largest contributor to greenhouse gas emissions and fuel usage. The Environmental Protection Agency and the National Highway Traffic Safety Administration finalized regulations in April 2010 to reduce greenhouse gas emissions and improve fuel economy for 2012-2016 model year light-duty vehicles. In November 2010, both agencies jointly proposed the first ever greenhouse gas standards for medium- and heavy-duty trucks which are expected to take effect for model years starting in 2014. Vehicles of light-duty families are subject to mandatory testing for certification and compliance. Unlike the light-duty sector where a vast majority of vehicles are mass produced for generally similar purposes, medium- and heavy-duty vehicles are commonly custom-made.

This work presents a method for simultaneously capturing visible and infrared images along with pressure data in an optical Diesel engine based on the International 4.5L VT275 engine. This paper seeks to illustrate the merits of each imaging technique for visualizing both in-cylinder fuel spray and combustion. The engine was operated under a part load, high simulated exhaust gas recirculation operating condition. Experiments examining fuel spray were conducted in nitrogen. Overlays of simultaneously acquired infrared and visible images are presented to illustrate the differences in imaging between the two techniques. It is seen that the infrared images spatially describe the fuel spray, especially fuel vapors, and the fuel mixing process better than the high-speed visible images.

We have established an equation for the density of hydrogen gas that agrees with the current standard to within 0.01 % from 220 to 400 K with pressures up to 45 MPa. The equation is a truncated virial-type equation based on pressure and temperature dependent terms. The density uncertainty for this equation is the same as the current standard and is estimated as 0.2 % (combined uncertainty with a coverage factor of 2). Comparisons are presented with experimental data and with the full 32-term equation of state.

A Repeatable Car (REPCA) program has been developed at the Environmental Protection Agency's National Vehicle and Fuel Emissions Laboratory (NVFEL) as part of an ongoing effort to improve the precision of fuel economy and emissions measurements. This concept of using a repeatable car as an integrated system diagnostic tool is not a new idea in the emissions testing field; however, our statistical analyses and organizational approach may be different from what other laboratories are using. Furthermore, given the NVEFL's role in automotive emissions testing, we felt it appropriate to provide related industries a detailed account of our standard laboratory practices, both for informational and comparative purposes. In order to separate vehicle and measurement variability in a relatively simple manner, a process was developed to track REPCA data based on Statistical Process Control principles using the calculation of individual site offset values from two week moving averages.

The effect of compaction and fiber volume fraction on the transverse permeability of a fluid flowing through stacked layers of fiber mats has been experimentally studied. A Unifilo-101 random mat of continuous glass strands, held together with a binder soluble in styrene was used. The stacked layers were compacted using a Wabash instrumented press. Changing the maximum load, resulted in different fiber volume fractions. Mixtures of glycerol and water with viscosities between 85 and 100 mPa-s were used. This fluid is passed in a rectangular cell, through the fibers arranged transverse to the direction of flow. The pressure drop across the mat and the flow rate were monitored. The study was carried out at different flow rates of the fluid and was repeated for other fiber volume fractions. A power-law relation was observed between the permeability and the fiber volume fraction.

As environmental regulations become more stringent, manufacturers are confronted with the task of product-design considering environmental impacts. Life Cycle Analysis (LCA) is a developing technique that attacks this problem. LCAs provide environmental information for decision making by consumers, manufacturers, and governments. These decisions significantly affect the ability to maximize source reduction, re-use, recyclability, and recycled content. LCAs can aid in diminishing the negative impact a product has on the environment and can be utilized as a partial solution of our nations' (worlds') growing waste management problem. To date, the application of LCAs has varied from product comparison to process development and improvement. The results from these analyses have differed because of differing assumptions and differing choices of boundary conditions. An appropriate Life Cycle Analysis should be consistent across products, locations, and especially across experimenters.

In-cylinder flows in four-valve SI engines were examined by high frame rate flow visualization and two-component LDV measurement. It is believed that the tumble and swirl motion generated during intake breaks down into small-scale turbulence later in the cycle. The exact nature of this relationship is not well known. However, control of the turbulence offers control of the combustion process. To develop a better physical understanding of the in-cylinder flow, the effects of the cylinder head intake port configuration and the piston geometry were examined. For the present study, a 3.5L, four-valve engine was modified to be mounted on an AVL single cylinder research engine type 520. A quartz cylinder was fabricated for optical access to the in-cylinder flow. Piston rings were replaced by Rulon-LD rings. A Rulon-LD ring is advantageous for the optical access as it requires no lubrication.

Ring wear may not be a problem in most current automotive engines. However, a small alteration in the ring face geometry can significantly affect the hydrodynamic lubrication characteristics of the ring. This in turn can cause excessive frictional losses and blowby in an engine. As engines become more compact and highly loaded, ring wear is likely to be more severe than in current engines. In order to assess the effect of ring loading, a piston ring wear model has been developed through the use of ring dynamics analysis with the assumption of a linear relationship between ring wear and the friction work applied on the surface of the ring. This ring wear analysis clearly shows that the higher the engine speed, the lower the wear rates at the same power output. This finding is consistent with the limited experimental data available.

Hydraulic engine mounts are used in the automotive industry because they offer frequency and amplitude response characteristics superior to the conventional elastomeric engine mount. This response is well established but is not fully understood. Numerous articles have attempted to explain the complex behavior of these mounts using linear theory. This paper uses the same linear models developed in previous papers, but offers a more fundamental explanation of the system response using these previously derived two degree of freedom models. In addition, the source of engine vibrations and their corresponding frequency ranges are explained in detail. Techniques borrowed from control systems are used to interpret system response and terminology used in the automotive industry to describe the behavior of hydraulic engine mounts is clarified. Validation of the two degree of freedom model is made by comparison with experimental data.

Statistical Energy Analysis (SEA) is a useful tool for predicting the transmission of noise and vibration through the structures of automotive vehicles. This work discusses the identification of SEA internal loss factor parameters from experimental measurements of vehicle sound pressure levels and structural accelerations. A simple automotive vehicle SEA model can be constructed from elements idealized as uniform beams, flat plates and acoustic volumes. Such an SEA automotive vehicle model can accurately predict the vibro-acoustic response of an automotive vehicles when appropriate equivalent SEA parameters are identified from in situ experimental data. This paper will present an algorithm for identifying internal loss factors for SEA models. The paper will include an example of the application of the algorithm to identification of automotive vehicle internal loss factors from measured vehicle response data.