Search Results

Incremental Sheet Forming (ISF) is an emerging sheet metal prototyping technology where a part is formed as one or more stylus tools are moving in a pre-determined path and deforming the sheet metal locally while the sheet blank is clamped along its periphery. A deformation analysis of incremental forming process is presented in this paper. The analysis includes the development of an analytical model for strain distributions based on part geometry and tool paths; and numerical simulations of the forming process with LS-DYNA. A skew cone is constructed and used as an example for the study. Analytical and numerical results are compared, and excellent correlations are found. It is demonstrated that the analytical model developed in this paper is reliable and efficient in the prediction of strain distributions for incremental forming process.

The efforts of the ISO “Test Variability Task Force” have been aimed at improving the understanding and at reducing brake dynamometer test variability during performance testing. In addition, dynamometer test results have been compared and correlated to vehicle testing. Even though there is already a vast amount of anecdotal evidence confirming the fact that different procedures generate different friction coefficients on the same brake corner, the availability of supporting data to the industry has been elusive up to this point. To overcome this issue, this paper focuses on assessing friction levels, friction coefficient sensitivity, and repeatability under ECE, GB, ISO, JASO, and SAE laboratory friction evaluation tests.

The Service Bay Diagnostic System (SBDS) will be designed to assist the dealership technician in diagnosing and repairing Ford Motor vehicles. The system hardware will be configured around a Service Bay Computer with mass storage capability and auxiliary service equipment. Major system features include: guided service writer/customer interaction, interactive vehicle diagnostics, information management. capabilities, and an additional aid to identifying intermittent failures through the use of a portable over-the-road data acquisition device. In order to assist the technician in properly diagnosing the causal factor, the Service Bay Computer System will also be enhanced through the use of an expert system knowledge base.

We report measurements of interior automotive cabin forced acoustical response (SPL) as a function of frequency from 1 Hz to 200 Hz. The acoustical response was measured at eight positions in the vehicle tested, approximating the positions of passengers and points in between passengers. Variances in experimental data arising from the manner in which measuring equipment is setup in a particular vehicle are reported, and variations in data taken in similarly equipped vehicles are also reported. The purpose of these tests is to determine the measurement variability of a typical vehicle acoustic test.

Rapid Prototyping, Fabrication and Tooling is a process that blends a series of technologies (machines, tools, and methods) capable of generating physical objects directly from a CAD database. The process dramatically reduces the time spent during product development by allowing for fast visualization, verification, iteration, optimization, and fabrication of parts and tools. Many new techniques of tooling have been and are being developed by using rapid fabricated parts. These are having a dramatic impact on both timing and costs throughout the automotive industry. One area that these methods can be utilized to their full potential is motorsports. Of particular interest is the growing use of bridge tooling to provide first article through production intent parts that promote cost effective changes.

There are a number of benefits from Ford Motor Company's participation in motorsports. This paper will describe how an engineering team developed a CAE process to assist in the design of a race car to meet impact requirements, with the technology transfer benefit of improved impact performance of composite structures in passenger cars. In 1997/98, a CAE process was developed and applied in the design and test of Formula One race car composite impact structures. For this particular engineering effort, a Ford proprietary software program, COMP-COLLAPSE, was the primary analysis tool that was utilized to successfully predict impact performance. As a result, COMP-COLLAPSE was used extensively in the design of race car composite impact structures. There were two beneficiaries from this effort: Race Vehicles: Improved vehicle impact performance as well as design improvement in crush efficiency, packaging, weight, and manufacturing.

Lookup tables and functions are widely used in real-time embedded automotive applications to conserve scarce processor resources. To minimize the resource utilization, these lookup tables (LUTs) commonly use custom data structures. The lookup function code is optimized to process these custom data structures. The legacy routines for these lookup functions are very efficient and have been in production for many years. These lookup functions and the corresponding data structures are typically used for calibration tables. The third-party calibration tools are specifically tailored to support these custom data structures. These tools assist the calibrators in optimizing the control algorithm performance for the targeted environment for production. Application software typically contains a mix of both automatically generated software and manually developed code. Some of the same calibration tables may be used in both auto generated and hand-code [ 1 ] [ 2 ].

The constant Q transform consists of a geometrically spaced filter bank, which is close to the wavelet transform due to the feature of its increasing time resolution for high frequencies. On the other hand, it can be processed using the well-known FFT algorithm. In this sense, this tool is a middle term between Fourier and wavelet analyses, which can be used for stationary and non-stationary signals. Automotive NVH signals can be stationary (e.g., idle, cruise) or non-stationary, i.e., time-varying signals (e.g., door closing/opening, run-up, rundown). The objective of this work is to propose the use of the constant Q transform, developed originally for musical signal processing, for automotive NVH (run up, impact strip and door closing) time-frequency analyses. Also, similarities and differences of the proposed tool when compared with Fourier and wavelet analyses are addressed.

Seat Effective Amplitude Transmissibility (SEAT) values can be obtained from direct measurements at seat track and top or estimated from transmissibility data and seat track input. Vertical transmissibility was measured for sixteen seats and six subjects on the Ford Vehicle Vibration Simulator, and these 96 functions used to estimate the seat top response for rough road input. SEAT values were calculated, and good correlation to values computed from direct seat top measurements obtained (R2 of 0.86). Averaging transmissibilities and direct seat measurements over the 6 subjects to obtain correlations for the 16 seats improved R2 to 0.94, validating this approach.

A series of tests have been performed on a production vehicle to determine the characteristics of the external turbulent flow field in wind tunnel and road conditions. Empirical formulas are developed to use the measured data as source levels for a Statistical Energy Analysis (SEA) model of the vehicle structural and acoustical responses. Exterior turbulent flow and acoustical subsystems are used to receive power from the source excitations. This allows for both the magnitudes and wavelengths of the exterior excitations to be taken into account - a necessary condition for consistently accurate results. Comparisons of measured and calculated interior sound levels show good correlation.

A new experimental methodology has been developed to quantify spindle loads of a vehicle under actual operational conditions. The methodology applies an indirect six degree-of-freedom (6 DOF) frequency response function (FRF) measurement technique to obtain three translation/force and three rotation/moment FRFs of the suspension system of the vehicle. The Inverse Frequency Response Function (IFRF) method estimates the spindle loads under operational conditions. The feasibility and applicability of the developed methodology for vehicle road NVH applications was experimentally demonstrated. The results show that the methodology provides accurate spindle load estimation over a broad frequency range. This methodology can be used for benchmarking and target setting of spindle loads to achieve desired road NVH performance as well as for diagnosing root causes in problem solving applications.

Powertrain mounts are one of the important design characteristics of a vehicle. Powertrain is mostly mounted to the front subframe and once installed in a vehicle, powertrain mounting has an important role in determining the vehicle vibration characteristics. A good mounting system isolates engine input vibration from the vehicle body and minimizes the effect of road inputs to the customer. This paper discusses results of several dynamic models as they relate to noise, vibration and harshness (NVH) and compares the accuracy of these models. Various powertrain models are studied and their accuracy in comparison with full a vehicle model is discussed.

The development of embedded systems in automotive environment has brought a strong expansion in the number of applications dependent of programmable devices. A failure in any of these systems may cause different types of damages. Therefore, it requires a high confidence in their operation. Many of these faults are inserted during the coding process. A tool for formal verification of the implemented code could allow the detection of possible errors that could not be encountered during the testing phase. In this paper, we propose a method for verifying software from the reduced model of the software built automatically with information from multiple traces of program executions. To illustrate the application of the proposed method a case study for an automotive electronic module that controls the windshield wiper is presented.

Downhill tests are widely used as a method of evaluation, development and validation of braking efficiency, friction pair durability, braking balance, as well as fade characteristics and recovery of friction material properties. This test procedure is used for both: passenger vehicles and light & heavy commercial vehicles. The energy levels in the brake system are higher on commercial vehicles and the thermal characteristics much more critical. Added to the fact that such tests are conducted on public highways, it has an intrinsic security risk for both the vehicle tested and all others around. Until a few years ago, it was still feasible to conduct tests downhill on different routes keeping a high security level. Given an increasing traffic on highways, where the test is currently carried out, a need to create a similar downhill procedure (called Guaporé Mountain Test) within a Proving Ground under controlled conditions has been noticed.

Each supplier in the power tool industry offers unique tool features and packages. Competition and widespread individuality among manufacturers make it difficult to compare current air and new DC electric power tools. This experimental study compares air and electric hand-held tools based on laboratory testing and research of significant tool characteristics including heat buildup, tool impulse, cycle time and cost. Heat buildup in electric tools raised concerns as well as tool speed, although electric tools were in some instances only slightly slower than air tools. Electric tools, in general, do not have a lower torque-reaction impulse than air tools, but the correlation between tool-shutoff impulse and operator comfort remains unclear. Electric tools are more energy efficient than pneumatic tools, but their initial investment cost greatly outweighs the payback through reduced power usage.

A comparison between ‘Quasi-Transient’ and Steady-State (SAE J1349) engine dynamometer horsepower test procedures was conducted to determine the degree of correlation between the two test methods. Measurements demonstrated that the peak horsepower and torque measured using both techniques was similar. This information is useful as a development tool, because the ‘Quasi-Transient’ procedure allows for data to be collected over the engine RPM range much faster then the Steady-State method, allowing for the accurate testing of more engine/exhaust configurations in a shorter amount of time.

An estimate of the rate of attrition of passenger cars, needed to establish the service life expectancy of passenger cars, is of major interest whenever long range production plans are made, marketing strategies are developed, the total needs of vehicles on the roads are estimated, etc. Estimation of vehicle attrition is very complex, however, due to the lack of accurate data and the interaction of the parameters affecting attrition. In 1980 and 1985, similar studies of attrition [1,2] utilized vehicle registration data available as of July, 1979 and as of July, 1984. The object of this paper is to update the results of these papers, using the 1991 July registration data, available in May 1992. Within the scope of this paper the attrition rates of various passenger cars are compared and the effect of geographical location on the attrition rates and the change in attrition rates during the past twenty years are discussed.

QFD, FMEA, Process Improvement, Taguchi, Simultaneous Engineering, PDP, Project Management, DVP, DOE, …and the list goes on. Today's automotive product design engineers face a myriad of “tools” (methodologies, techniques, procedures) that are expected to be mastered and used in the course of performing their job. The list continually grows with new tools being added to the existing ones. And each new tool has an associated acronym to add to the confusion. New and inexperienced engineers are often confused by these tools being tossed at them …school did not cover all this ! The experienced engineer is often skeptical. After all, “if I have been a successful engineer for 20 years, why do I need to start doing these things now?” Nevertheless, most of these tools are truly needed by engineers today in order to be competitive in the increasingly complex and sophisticated world of automotive product design.

Here we present an analytical model, written in general terms, which predicts the trajectory of a spherical particle/droplet placed in a uniform fluid stream. The model is compared to an experiment in which three millimeter diameter polypropolyene spheres (specific gravity = 0.91) are dropped in a uniform airstream (velocity varies from 0.9 to 3.8 m/s). Agreement between the two suggests the model incorporates all the important physics and thus should be useful as a design tool.