Search Results

A pilot-main injection strategy is investigated for a part-load operating point in a single cylinder optical Diesel engine. As the energizing dwell between the pilot and main injections decreases below 200 μs, combustion noise reaches a minimum and a reduction of 3 dB is possible. This decrease in combustion noise is achieved without increased pollutant emissions. Injection schedules employed in the engine are analyzed with an injection analyzer to provide injection rates for each dwell tested. Two distinct injection events are observed even at the shortest dwell tested; rate shaping of the main injection occurs as the dwell is adjusted. High-speed elastic scattering imaging of liquid fuel is performed in the engine to examine initial liquid penetration rates.

As the new features for driver assistance and active safety systems are growing rapidly in vehicles, the simulation within a virtual environment has become a necessity. The current active safety system consists of Electronic Control Units (ECUs) which are coupled to camera and radar sensors. Two methods of implementation exists, integrated sensors with control modules or separation of sensors form control modules. The subsystem integration testing poses new challenges for virtual environment for simulation of active safety features. The comprehensive simulation environment for integration testing consists of chassis controls, powertrain, driver assistance, body and displays controllers. Additional complexity in the system is the serial communication strategy. Multiple communication protocols such as GMLAN, LIN, standard CAN, and Flexray could be present within the same vehicle topology.

This research examined driver acceptance and behavior associated with Speed Limit and Curve Advisor systems, including influences on speed choice. Drivers experienced messages from an emulated Speed Limit and Curve Advisor system during a 2-hour public road drive. Driver tolerance for system errors and message conflicts was also studied by manipulating the accuracy of the information provided by the system. Messages were presented using either a Head-Up Display or on an in-dash Driver Information Center. Results indicate that drivers liked having speed limit information continuously available to them while driving, but the information provided by the Speed Limit Advisor did not significantly influence or alter drivers' speed choice or deceleration profiles in comparison to driving without the system.

An analysis of the first 35 back-over crashes reported by NHTSA's Special Crash Investigations unit was undertaken with two objectives: (1) to test a hypothesized classification of backing crashes into types, and (2) to characterize scenario-specific conditions that may drive countermeasure development requirements and/or objective test development requirements. Backing crash cases were sorted by type, and then analyzed in terms of key features. Subsequent modeling of these SCI cases was done using an adaptation of the Driving Reliability and Error Analysis Methodology (DREAM) and Cognitive Reliability and Error Analysis Methodology (CREAM) (similar to previous applications, for instance, by Ljung and Sandin to lane departure crashes [10]), which is felt to provide a useful tool for crash avoidance technology development.

Alternative implementations of a Rear Cross Traffic Alert (RCTA) system intended to actively notify drivers of the presence of rear cross-path traffic when backing were evaluated in naturalistic settings. The feature is one of several emerging technologies designed to assist drivers when backing - in this case, enhancing drivers' awareness of traffic approaching from the rear. The study allowed performance under a range of RCTA system driver interface implementations to be contrasted with conventional and wide Field of View (FOV) Rear Vision systems. Evaluations were conducted using a sample of 70 drivers under naturalistic settings and environments with repeated exposures to backing tasks. The study also made use of a staged conflict situation with a confederate vehicle in order to more precisely quantify driver behavior and system usage across drivers under controlled conflict situations.

Vehicle-to-vehicle (V2V) communication systems can enable a number of wireless-based vehicle features that can improve traffic safety, driver convenience, and roadway efficiency and facilitate many types of in-vehicle services. These systems have an extended communication range that can provide drivers with information about the position and movements of nearby V2Vequipped vehicles. Using this technology, these vehicles are able to communicate roadway events that are beyond the driver's view and provide advisory information that will aid drivers in avoiding collisions or congestion ahead. Given a typical communication range of 300 meters, drivers can potentially receive information well in advance of their arrival to a particular location. The timing and nature of presenting V2V information to the driver will vary depending on the nature and criticality of the scenario.

Developing common methods of noise evaluation and facilities can present a number of challenges in the area of tire/pavement noise. Some of the issues involved include the design and construction of pavements globally, the change in pavement over time, and variation in the noise produced with standard test tires used as references. To help understand and address these issues for airborne tire/pavement noise, acoustic intensity measurement methods based on the On-board Sound Intensity (OBSI) technique have been used. Initial evaluations have included measurements conducted at several different proving grounds. Also included were measurements taken on a 3m diameter tire noise dynamometer with surfaces replicating test track pavements. Variation between facilities appears to be a function of both design/construction and pavement age. Consistent with trends in the literature, for smooth asphalt surfaces, the newest surface produced levels lower than older surfaces.

This paper presents the implementation of an off-line optimized torque vectoring controller on an electric-drive vehicle with four in-wheel motors for driver assistance and handling performance enhancement. The controller takes vehicle longitudinal, lateral, and yaw acceleration signals as feedback using the concept of state-derivative feedback control. The objective of the controller is to optimally control the vehicle motion according to the driver commands. Reference signals are first calculated using a driver command interpreter to accurately interpret what the driver intends for the vehicle motion. The controller then adjusts the braking/throttle outputs based on discrepancy between the vehicle response and the interpreter command.

The battery system in the Chevrolet Volt is very complex and must balance a variety of performance criteria, including the safety of vehicle occupants and other users. In order to assure a thorough approach to battery system safety, a system safety engineering process was applied and found to provide a useful framework. This methodical approach began with the preliminary hazard analysis and continued through requirements definition, design development and, finally, validation. Potentially hazardous conditions related directly to functional safety (for example, charge control) and primary physical safety (for example, short circuit conditions) can all be addressed in this manner. Typical battery abuse testing, as well as newly defined limit testing, supported the effort. Extensive documentation, traceability and peer reviews helped to verify that all issues were addressed.

This study documents a method developed for dynamically measuring occupant pocketing during various low-speed rear impact, or “whiplash” sled tests. This dynamic pocketing measurement can then be related to the various test parameters used to establish the performance rating or compliance results. Consumer metric and regulatory tests discussed within this paper as potential applications of this technique include, but are not limited to, the Insurance Institute for Highway Safety (IIHS) Low Speed Rear Impact (LSRI) rating, Federal Motor Vehicle Safety Standard (FMVSS) 202a, and European New Car Assessment Program (EURO-NCAP) whiplash rating. Example metrics are also described which may be used to assist in establishing the design position of the head restraint and optimize the balance between low-speed rear impact performance and customer comfort.

Engineering has continuously strived to improve the vehicle development process to achieve high quality designs and quick to launch products. The design process has to have the tools and capabilities to help ensure both quick to the market product and a flawless launch. To achieve high fidelity and robust design, mistakes and other quality issues must be addressed early in the engineering process. One way to detect problems early is to use the math based modeling and simulation techniques of the analysis group. The correlation of the actual vehicle performance to the predictive model is crucial to obtain. Without high correlation, the change management process begins to get complicated and costs start to increase exponentially. It is critical to reduce and eliminate the risk in a design up front before tooling begins to kick off. The push to help achieve a high rate of correlation has been initiated by engineering management, seeing this as an asset to the business.

General Motors (GM) and the Virginia Tech Transportation Institute (VTTI) have partnered to conduct a series of studies characterizing the use and effectiveness of technologies designed to assist drivers while backing. A major emphasis of this research has been on Rear Vision Camera (RVC) systems that provide drivers with an enhanced view of the area behind the vehicle. RVC systems are intended to aid in positioning the vehicle when executing low-speed parking and backing-related tasks and are not necessarily well suited for detecting unexpected in-path obstacles (particularly if the RVC image is not coupled with object detection alerts issued to the driver).

Compartment noise has gained significant importance to meet customer expectation. One of the sources of noise is air intake noise. Intake noise is produced by both opening and closing of the inlet valve. This makes source noise critical to the development of air induction system. The new approach has been thought for noise analysis of Air Induction System (AIS) to identify source noise using 1D-3D coupling. It is very difficult to simulate engine and air induction system in Computational Fluid Dynamics (CFD) due to complexities in geometry. The objective of the present study is to predict the pulsed noise and flow noise using 1D-3D coupling. The engine with 1D code and AIS with 3D CFD code is simulated. Engine pulsation from GT-Power is provided as an input boundary condition to ANSYS Fluent. GT-Power exchanges boundary values to 3D computation domain at each CFD time step through special connections. The CFD code is run with implicit discretisation scheme and SAS turbulence model.

A structural-acoustic finite element model of an automotive vehicle is developed and applied to evaluate the effect of structural and acoustic modifications to reduce low-frequency ‘boom’ noise in the passenger compartment. The structural-acoustic model is developed from a trimmed body structural model that is coupled with an acoustic model of the passenger compartment and trunk cavities. The interior noise response is computed for shaker excitation loads at the powertrain mount attachment locations on the body. The body panel and modal participation diagrams at the peak response frequencies are evaluated. A polar diagram identifies the dominant body panel contributions to the ‘boom’ noise. A modal participation diagram determines the body modes that contribute to the ‘boom’ noise. Finally, structural and acoustic modifications are evaluated to determine their effect on reducing the ‘boom’ noise and on the overall lower-frequency sound pressure level response.

With the introduction of hybrid vehicles and the associated elimination of engine and exhaust masking noises, sounds from other sources is becoming more noticeable. Fuel tank sloshing is one of these sources. Fuel sloshing occurs when a vehicle is accelerated in any direction and can create noise that may be perceived as a quality issue by the customer. To reduce slosh noise, a fuel tank has to be carefully designed. Reduction in slosh noise using test- based methods can be very costly and timely. This paper shows how, using the combination of CFD (Computational Fluid Dynamic), FE (Finite Element) and Acoustic simulation methods, the radiated fuel tank slosh noise performance can be evaluated using CAE methods. Although the de-coupled fluid /structure interaction (FSI) method was used for the examples in this paper, the acoustic simulation method is not limited to the decoupled FSI method.

Research was conducted to assess driver acceptance and performance associated with a spotter mirror feature intended to reduce the incidence of lane-change conflicts by enhancing drivers' ability to detect vehicles in their side blind zone. The spotter mirror consisted of an integrated spherical convex blind zone mirror inset within a larger planar mirror. The spotter mirror's field-of-view was designed to target the vehicle's side blind zone area and to help drivers quickly detect the presence or absence of a vehicle in the blind zone. The study captured normative lane-change behavior during an extended drive on public roadways, with and without access to the spotter mirror system, for a sample of familiar and unfamiliar supplemental mirror users. In order to capture more naturalistic lane-change behavior, drivers were informed that the purpose of the study was to evaluate the adequacy of existing road signs for navigating to a destination.

Internally excited torsional steering wheel vibrations at frequencies near 8-22 Hz on smooth roads can produce driver disturbances, commonly described as “SHAKE”. These vibrations are primarily excited by the rotating front suspension corners and are periodic in the rotational frequencies of the tire-wheel assemblies. The combination of vehicular dynamic amplification originating in dominant suspension and steering system vibratory modes, and a sufficiently large 1st harmonic non-uniformity excitation of the rotating corner components, can result in periodic vibrations exceeding thresholds of disturbance. Controlling the periodic non-uniformity excitation through individual component requirements (e.g., wheel imbalance, tire force variation, wheel runout, concentric piloting of wheel on hub) is difficult since the desired upper limits of individual component requirements for vibration-free performance are typically beyond industry capability.

In order to assess the possible ways of energy transfer from the various sources of excitation in a vehicle assembly to a given target location, frequency based substructuring technique and transfer path analysis are used. These methods help to locate the most important energy transfer paths for a specific problem, and to evaluate their individual effects on the target, thus providing valuable insight into the mechanisms responsible for the problem. The Source-Path-Receiver concept is used. The sources can be from the road surface, engine, transmission, transfer case, prop-shaft, differential, rotating components, chain drives, pumps, etc., and the receiver can be driver/passenger ears, steering column, seats, etc. This paper is devoted to identify the noise transfer paths and the force transmissibility among the interfaces of different components in the vehicle for the low to mid frequency range.

The present study defines the functional requirements for a liftgate and the body in order to avoid rattle, squeak, and other objectionable noises. A Design For Six Sigma (DFSS) methodology was used to study the impact of various constraint components such as bumpers, wedges, and isolated strikers on functional requirements. These functional requirements include liftgate frequency, acoustic cavity frequency, and the stiffness of the liftgate body opening. It has been determined that the method of constraining the gate relative to the body opening has a strong correlation to the noise generated. The recommended functional performance targets and constraint component selection have been confirmed by actual testing on a vehicle. Recommendations for future liftgate design will be presented.

The plug-in vehicles developed in the 1990's ushered in the first standards for electrified vehicles. These standards included requirements for Electric Vehicle Supply Equipment or EVSEs. EVSE is a general term for all the non vehicle components needed to charge a plug-in vehicle. These components include cabling, connectors and shock safety equipment. EVSEs are used to charge vehicles at home, work and in commercial settings. Many people identify EVSEs with public charge stations. While public charge stations are iconic with plug-in vehicles, these are just one type of EVSE. Until public EVSEs become readily available, plug-in vehicle drivers will need to partially rely on portable versions of EVSE. Portable EVSEs are required to provide the identical function and safety protection as their stationary cousins but their portability brings unique challenges and design considerations.