Search Results

We have developed a bench test method to assess driver distraction caused by the load of using infotainment systems. In a previous study, we found that this method can be used to assess the task loads of both visual-manual tasks and auditory-vocal tasks. The task loads are assessed using the performances of both pedal tracking task (PT) and detection response task (DRT) while performing secondary tasks. We can perform this method using simple equipment such as game pedals and a PC. The aim of this study is to verify the reproducibility of the PT-DRT. Experiments were conducted in three test environments in which test regions, experimenters and participants differed from each other in the US, and the test procedures were almost the same. We set two types of visual-manual tasks and two types of auditory-vocal tasks as secondary tasks and set two difficulties for each task type to vary the level of task load.

A sports car exhibits many challenges from an aerodynamic point of view: drag that limits top speed, lift - or down force - and balance that affects handling, brake cooling and insuring that the heat exchangers have enough air flowing through them under several vehicle speeds and ambient conditions. All of which must be balanced with a sports car styling and esthetic. Since this sports car applies two electric motors to drive front axle and a high-rev V6 turbo charged engine in series with a 9-speed double-clutch transmission and one electric motor to drive rear axle, additional cooling was required, yielding a total of ten air cooled-heat exchangers. It is also a challenge to introduce cooling air into the rear engine room to protect the car under severe thermal conditions. This paper focuses on the cooling and heat resistance concept.

The practical application of heat recovery using thermoelectrics requires the realization of reasonable cost effectiveness. Therefore, a thermoelectric generator (TEG) structure that can compatibly increase efficiency and reduce cost was investigated with the aim of enhancing cost effectiveness. To increase efficiency, a method of using a vacuum space structure to reduce the TEG size was investigated to enable installation just after the close-coupled catalyzer, which is subject to many space restrictions. It was found that by making it possible to use high temperature exhaust heat, power generation efficiency can be increased to approximately twice that of the typical under floor installation. In addition, coupled simulation of heat transfer and power generation using FEM, 1D cost effectiveness simulations, and bench tests were performed with the aim of reducing cost.

A new piston secondary motion analysis has been developed that accurately predicts piston strength and the slap noise that occurs when the engine is running. For this secondary motion analysis, flexible bodies are used for the models of the piston, cylinder and cylinder head. This makes it possible to quantify the deformations and secondary motion occurring in each area of the engine. The method is a coupled analysis of the structure analysis and the multi body dynamics analysis. The accuracy of the results obtained in the new analysis method was verified by comparing them to measurement data of piston skirt stress and piston secondary motion taken during firing. To measure piston skirt stress, a newly developed battery-powered telemetric measurement system was used. The calculation results were close to the measurement results both for stress and for secondary motion from low to high engine speed.

Improvement of engine cycle thermal efficiency is an effective way to increase engine torque and to reduce fuel consumption simultaneously. However, the extent of the improvement is limited by engine knock, which is more evident at low engine speeds when combustion flame propagation is relatively slow. To prevent engine damage due to knock, the spark ignition timing of a gasoline engine is usually controlled by a knock sensor. Therefore, an engine's ignition timing cannot be set freely to achieve best engine performance and fuel economy. Whether ignition timings for a multi-cylinder engine are the same or can be set differently for each cylinder, it is not desirable for each cylinder has big deviation from the median with respect to knock tendency. It is apparent that effective measures to improve engine knock toughness should address both uniformity of all cylinders of a multi-cylinder engine and improvement of median knock toughness.

In the development of a magnetic-coupling water pump, the pulling-out (disengagement) of a coupling that led to the stopping of an impeller was a concern. Upon analysis of the behavior of the magnetic coupling, presence of two types of the pulling-out was found, that is, the pulling-out resulting from a lack of transfer torque in the high-speed revolutions and the pulling-out due to the resonance of an inner magnet and an outer magnet. Main factors that affect the pulling-out are the angular velocity input to the drive side, the moment of inertia of the driven side, characteristics of the magnetic coupling, and a damping from coolant. Using a measurement and simulation of the behavior of the water pump, factors were analyzed and the process of pulling-out was clarified. As a result, design specifications that prevented the pulling-out were established.

This paper introduces a new type of aluminum radiator that has been developed with the objective of high performance and light weight. Aluminum radiators have recently been replacing copper radiators because of their light weight, but the heat rejection of such conventional alminum radiators does not exceed that of copper radiators. Authors established the aluminum radiator not only being light weight but also having high performance through the following approaches. (1) Optimization of radiator core module. (2) Thickness reduction of tube and fin. (3) Development of aluminum alloys with improved corrosion resistance for tubes and fins. As a result, a new type single-row aluminum radiator has achieved 7% higher rejection at 50% lighter weight than those of copper double-row radiator.

The use of electric vehicles (EV) is becoming more widespread as a response to global warming. The major issues associated with EV are the annoyance represented by charging the vehicles and their limited cruising range. In an attempt to remove the restrictions on the cruising range of EV, the research discussed in this paper developed a dynamic charging EV and low-cost infrastructure that would make it possible for the vehicles to charge by receiving power directly from infrastructure while in motion. Based on considerations of the effect of electromagnetic waves, charging power, and the amount of power able to be supplied by the system, this development focused on a contact-type charging system. The use of a wireless charging system would produce concerns over danger due to the infiltration of foreign matter into the primary and secondary coils and the health effects of leakage flux.

The present study experimentally investigated cyclic variation of combustion characteristics of a diesel engine with hydrogen added to the intake air in detail. As the result, there were three ignition modes: (1) hydrogen ignition mode, (2) hydrogen-assisted ignition mode, and (3) diesel-fuel ignition mode. Ignition timing fluctuated from cycle to cycle in each ignition mode and between one ignition mode and another mode. As the coolant temperature was increased, the number of cycles in diesel-fuel ignition mode decreased, and indicated thermal efficiency and cyclic variation was improved. In the case with the blow-by gas introduced to intake port, preflame reaction of blow-by gas first occurred, ignited hydrogen, and then diesel-fuel was ignited by hydrogen combustion in hydrogen ignition mode and hydrogen-assisted ignition mode.

This paper describes the oil-film bearing analysis simulation was utilized for the optimization of pin boss form which reduces a piston-pin noise. It is clear from the mechanism analysis of the piston-pin noise which is the last research that an oil-film flow inside a pin boss is an important factor for pin noise reduction. So, in this research, the oil-film simulation of the piston-pin-boss bearing part was performed using oil-film bearing analysis tool. After setting up the simulation conditions of the oil-film bearing part so that actual pin behavior and high correlativity might be shown, a parameter, effective hydrodynamic angular velocity, and an oil flow rate of change suitable for evaluation of a pin noise were found out. The pin noise in semi floating piston was reduced to the same level as full floating type by applying pin boss form to which each evaluation parameter becomes the optimal to a piston.

A method was designed to predict the gasket surface pressure in consideration of creep which occurs on the surface of the gasket side of the cylinder head in air-cooled engines. Creep caused by heat can cause major deformation on the gasket side of the cylinder head in air-cooled engines, which may result in combustion gas leaking from between the cylinder and cylinder head. Until now, there have been no reports of methods to accurately predict phenomena relating to this deformation in the initial stage of engine design. This study combined values of strain and temperature occurring on the gasket side of the cylinder head, obtained through FEM analysis of steady heat transfer and thermal stress, with unit test results showing the domains in which the influence of the creep is critical or not. This information was used to design a method to determine whether or not an engine's specifications fell into a domain in which creep would have an effect, and predict surface pressure.

The goal of this research topic is to accurately and rapidly evaluate appearance marketability from the point of view of the customer. 3D data has been broadly used in automobile development in recent times, and utilizing digital models built by this data is effective for quickly and definitively evaluating marketability. Therefore, TOPS was developed, an optimal graphic tool for evaluating appearance marketability that anyone can easily use to portray graphics that are equivalent to the actual product. The development of TOPS increased the precision and efficiency of digital development in design.

Catalyst simulation, which can analyze the complicated reaction pathway of exhaust gas purifications and identify the rate-determining step, is an essential tool in the development of catalyst materials. This requires an elementary reaction model which describes the detailed processes, i.e. adsorption, decomposition, and others. In our previous work, the elementary reaction model on Pt/CeO2 catalyst was constructed. In this study, we focused on extending the Zeolite catalyst and including the gas diffusivity through the catalyst layer. The reaction rate of a Zeolite catalyst was expressed by an Arrhenius equation, and the elementary reaction model was composed of 17 reactions. Each Arrhenius parameter was optimized by the catalytic activity measurements. The constructed model was validated with NOx conversion in cyclic experiments which were repeated with Lean phase (NOx adsorption) and Rich phase (NOx reduction).

In our preceding report [1], we showed that the thermal conductivity of a heat pipe dramatically improves during high-speed reciprocation. However, this cooling method has rarely been applied to car engine pistons because the thermal conductivity of commercially available heat pipes does not increase easily even if the pipe is subjected to high-speed reciprocation. In consideration of the data from our preceding report, we decided to investigate heat pipe designs for car engine pistons, propose an optimum design, and conduct thermal analysis of the design. As a result, we found that it is possible to transport heat from the central piston head area, where cooling is most needed, to the piston skirt area, suggesting the possibility of efficient cooling.

Car engine piston cooling is an important technology for improving the compression ratio and suppressing the deformation of pistons. It is well known that thermal conductivity improves dramatically through the use of heat pipes in computers and air conditioners. However, the heat pipes in general use have not been used for the cooling of engines because the flow of gas and liquid is disturbed by vibration and the thermal conductivity becomes excessively low. We therefore developed an original heat pipe and conducted an experiment to determine its heat transfer coefficient using a high-speed reciprocation testing apparatus. Although the test was based on a single heat pipe unit, we succeeded in improving the heat transfer coefficient during high-speed reciprocation by a factor of 1.6 compared to the heat transfer coefficient at standstill. This report describes the observed characteristics and the method of verification.

The cooling performance and the heat resistance performance of commercial vehicle are balanced with aerodynamic performance, output power of powertrain, styling, cost and many other parameters. Therefore, it is desired to predict the cooling performance and the heat resistance performance with high accuracy at the early stage of development. Among the three basic forms of heat transfer (conduction, convection and radiation), solving thermal conduction accurately is difficult, because modeling of “correct shape” and setting of coefficient of thermal conductivity for each material need many of time and efforts at the early stage of development. Correct shape means that each part should be attached correctly to generate the solid mesh with high quality. Therefore, it is more efficient and realistic method to predict the air temperature distribution around the rubber/resin part instead of using the surface temperature at the preliminary design stage.

For detailed temperature estimates in the engine of a running motorcycle, newly researches were conducted on the method for calculation of temperature distribution using a three-dimensional (3D) thermal conductivity simulation after calculating the total balance of heat generation and heat dissipation of the engine using a one-dimensional (1D) thermal simulation. This project is targeted at air-cooled engines in which the cooling conditions vary significantly depending on the external shapes of the engines and the airflow around them. The heat balance is calculated using the 1D thermal simulation taking into account all the routes and processes for dissipation to the atmosphere of the heat that is generated by the combustion in the engine. The 1D engine cycle simulation is applied to calculate the heat transmission to the engine from the combustion. For the calculation of heat transfer within the engine, the engine components are converted to a one-dimensional model.

A method applicable in the design stage to predict fatigue strength of a motorcycle exhaust system was developed. In this prediction method, a vibrating stress, thermal stresses, stresses resulting from the assembling of the exhaust system components and a deterioration of fatigue strength of materials originated from high temperature were simultaneously taken into account. For the prediction of the vibrating stress, flexible multibody dynamics was applied to get modeling accuracy for vibration characteristics of the entire motorcycle and the exciting force delivered from engine vibrations. The thermal conduction analysis and the thermal deformation analysis based on finite element method (FEM) were applied for the prediction of thermal stresses in the exhaust system components. The temperature distribution on the surfaces of the exhaust system components is required for calculations of the thermal stresses.

Recently, the electronic fuel injection systems have been widely applied to small motorcycles including scooters. In the high pressure fuel lines, plastic hoses have been increasingly used instead of conventional rubber hoses. As the plastic hose is less elastic than the rubber hose, the fuel pressure pulsates more in the plastic hose. To cope with this issue, we have conducted researches on how the fuel pressure pulsation in the plastic hose affects the accuracy of fuel injection. Keeping our eyes on the pulsation damping effects derived from the changes of volume due to the expansion and contraction of hose when the pressure changes, we have established the analysis method for optimization of the inner diameter and the thickness of the hose utilizing CAE analysis. The newly-developed plastic hose is applicable to motorcycles having a single cylinder 250 cm3 engine using an injector of a high static flow rate.

The dynamic performance of battery electric vehicles (BEV) is affected by battery output power, which depends on state of charge (SOC) and the temperature of battery cells. The temperature of the batteries varies in particular with the environment, in which the user stores the vehicle, and the battery output power. It is therefore necessary to employ thermal management systems that can control the battery temperature within the optimal range under severely hot and cold conditions in BEVs. A highly sophisticated thermal management system and its operation strategy were developed to fulfill the above requirements. The powertrain components to be thermo-controlled were located into two coolant circuits having different temperature range. The compact and efficient front-end heat exchangers were designed to optimally balance the cooling performance of powertrain, cabin comfort, vehicle aerodynamics and the vehicle design.