Search Results

In this research, a new wire material made using surface-reforming heat treatment was developed in order to enhance the corrosion fatigue resistance of suspension springs. The aim of surface reforming is to improve hydrogen embrittlement characteristics through grain refinement and to improve crack propagation resistance by partial softening of hardness. The grain refinement method used an α'→γ reversed transformation by rapid short-term heating in repeated induction heating and quenching (R-IHQ) to refine the crystal grain size of SAE 9254 steel spring wire to 4 μm or less. In order to simultaneously improve the fatigue crack propagation characteristics, the possibility of reducing the hardness immediately below the spring surface layer was also examined. By applying contour hardening in the second IHQ cycle, a heat affected zone (HAZ) is obtained immediately below the surface.

Glass fiber reinforced plastic of polyamide is applied as one of the materials used for the high strength exterior parts of a motorcycle, such as a rear grab rail or a carrier, to which both strength and good exterior appearance are required. However, Glass Fiber reinforced Polypropylene (PPGF), which is relatively inexpensive material, has a property that the contained glass fibers are prone to be exposed at the surface and, therefore, the requirements for good appearance are hardly met by using PPGF. In this study, Heat and Cool molding method (H&C molding) was employed to realize a cost reduction by using PPGF yet without applying painting process, and the established method was applied to mass production while fulfilling the requirements for a good exterior appearance. In H&C molding, the metal molds are heated up by steam and cooled down by water after molding.

Recent trends to downsize engines have resulted in lighter weight and greater compactness. At the same time, however, power density has increased due to the addition of turbocharger and other such means to supplement engine power and torque, and this has increased the thermal and mechanical load. In this kind of environment, corrosion of the copper alloy bushing (piston pin bushing) that is press-fitted in the small end of the connecting rod becomes an issue. The material used in automobile bearings, of which the bushing is a typical example, is known to undergo sulfidation corrosion through reaction with an extreme-pressure additive Zinc Dialkyldithiophosphate (ZnDTP) in the lubricating oil. However, that reaction path has not been clarified. The purpose of the present research, therefore, is to clarify the reaction path of ZnDTP and copper in an actual engine environment.

Conventionally, the Ni-based superalloys NCF3015 (30Ni-15Cr) and the high nickel content NCF440 (70Ni-19Cr) (with its outstanding wear resistance and corrosion resistance), have been used as engine exhaust valve materials. In recent years, automobile exhaust gases have become hotter because of exhaust gas regulations and enhanced fuel consumption efficiency. Resource conservation and cost reductions also factor into global environmental challenges. To meet these requirements, NCF5015 (50Ni-15Cr), a new resource-conserving, low-cost Ni-based heat-resistant alloy with similar high-temperature strength and wear resistance as NCF440, has been developed. NCF5015's ability to simultaneously provide wear resistance, corrosion resistance and strength when NCF5015 is used with diesel engines was verified and the material was then used in exhaust valves.

The environmental performance of automobiles and automobile engines in particular is the foremost issue in the automotive industry today. In addition, engine durability performance is an essential aspect of engine oil performance. Four-cycle motorcycle engine oils formulated with dialkyl phosphate, a sulfur-free additive developed as an alternative to ZDDP, provide excellent environmental and durability performance in terms of longer drain intervals, cleanliness and low corrosion properties.

A compact, low-cost fuel pump module has been developed for use in motorcycles with a small-displacement engine. Various considerations are given to make the module as compact as possible. The pump motor, which is one of the major component parts, is down-sized specifically for applications to small-displacement engines. The pressure regulator uses a simple construction consisting only of a ball and a spring without a diaphragm. Especially noteworthy is that with the volume reduced by approximately 40% from the conventional pressure regulator while using the construction that reduces self-excited vibrations caused by fuel pressure pulsations, the pressure regulator contributes significantly to the down-sizing and cost reduction of the module. Furthermore, the down-sized module remarkably reduces the size of fuel pump mount surface, allowing a modification from the flat-surface sealing to the radial sealing.

Using sand cores, the weld-able, hollow die-cast parts have been developed. For casting, the transition flow filling method is applied to reduce gas containment and to minimize damages to the core. In designing the products, the newly developed core stress prediction system by melt pressure distribution and the newly developed in-product gas containment prediction system have been applied. The hollow die-cast frame made by the new method attains a 30% increase in rigidity and 1kg reduction of weight.

The International Lubricant Standardization and Approval Committee (ILSAC) ATF subcommittee members have compared the two oxidation bench test methods, Aluminum Beaker Oxidation Test (ABOT) and Indiana Stirring Oxidation Stability Test (ISOT), using a number of factory-fill and service-fill ATFs obtained in Japan and in the US. In many cases, the ATFs were more severely oxidized after the ABOT procedure than after the same duration of the ISOT procedure. The relative severity of these two tests was influenced by the composition of the ATFs. The bench test oxidation data were compared with the transmission and the vehicle oxidation test data.

A new type of lean NOx catalyst has been developed with improved thermal resistance. This lean NOx catalyst contains precious metals and NO2 adsorbents. The precious metals are used mainly for the oxidation reaction of NO, and the NO2 adsorbents are for the adsorption removal of generated NO2. The thermal resistance of the catalyst was raised by paying attention to the following points. 1) Improvement of thermal resistance for the NO oxidation activity by addition of a different precious metal element. 2) Prevention of thermal degradation of the NO2 adsorbent by addition of a new metal oxide. For item 1, Pd was added to the catalyst which had already included Pt. By having Pd coexist with Pt, the precious metal dispersion was kept high even after heat treatment, so the NO oxidizing ability was improved. For item 2, thermal degradation of NO2 adsorbent was prevented by addition of the new metal oxide (B) to the adsorbent.

The PVC(poly-vinyl chloride) underbody coating was specifically designed for the automotive underfloor area in order to prevent chipping damage as well as the onset of rust propagation from a scratched point. This superior anti-chipping performance can also be achieved without increasing film thickness of the PVC by balancing film strength and adhesion strength. Also, by incorporating plastic balloons in the PVC formulation, a dried film specific gravity of less than 1.0 is achieved, and consequently a 2 kg weight reduction becomes possible when compared to conventional materials used for underbody coating.

For the purpose of developing onboard gasoline reforming technology for higher octane number fuel on demand, octane number enhancement of gasoline surrogate by aerobic oxidation using N-hydroxyphthalimide catalyst was investigated. At first, octane numbers of the oxygen-containing products from alkane and aromatic compound were estimated using a fuel ignition analyzer. As a result, not only alcohol but also ketones and aldehydes have higher octane numbers than the original alkanes and aromatic compound. Next, gasoline surrogate was oxidized aerobically with N-hydroxyphthalimide derivative catalyst and cobalt catalyst at conditions below 100 °C. As a result, fuel molecules were oxidized to produce alcohols, ketones, aldehydes, and carboxylic acids. N-hydroxyphthalimide derivative catalyst with higher solubility in gasoline surrogate has higher oxidation ability. Furthermore, the estimated octane number of the oxidized gasoline surrogate improves 17 RON.

Manganese oxides show high catalytic activity for CO and HC oxidation without including platinum group metals (PGM). However, there are issues with both thermal stability and resistance to sulfur poisoning. We have studied perovskite-type YMnO₃ (YMO) with the aim of simultaneously achieving both activity and durability. This paper describes the oxidation activity of PGM-free Ag/i-YMO, which is silver supported on improved-YMO (i-YMO). The Ag/i-YMO was obtained by the following two methods. First, Mn⁴+ ratio and specific surface area of YMO were increased by optimizing composition and preparation method. Second, the optimum amount of silver was supported on i-YMO. In model gas tests and engine bench tests, the Ag/i-YMO catalyst showed the same level of activity as that of the conventional Pt/γ-Al₂O₃ (Pt = 3.0 g/L). In addition, there was no degradation with respect to either heat treatment (700°C, 90 h, air) or sulfur treatment (600°C to 200°C, total 60 h, 30 ppm SO₂).

There are several all-aluminum cylinder blocks. A typical example is a mono-block cylinder of alusil alloy produced by low pressure die casting. This material's resistance to abrasion and seizure, however, is not satisfactory for motorcycle; in addition, long processing time is another disadvantage. To cope with these problems, the authors developed a light and highly productive all-aluminum cylinder block with a cast-in liner through die casting. The liner is made from powder metallurgy composite (PMC) with 3 to 5 % alumina and 0.5 to 3 % of graphite additives. The PMC reconciles abrasion resistance and machinability. The hardness deterioration of the composite due to the heat at die casting is avoided by using heat-resistant rapidly-solidified powders, made from an aluminum-silecon-iron alloy, for the matrix.

High viscosity index(HVI) petroleum base stock, with excellent temperature-viscosity characteristics, oxidation resistance, and low-evaporation properties, offers advantages as the base stock for high fuel economy engine oils, particularly because of its low-friction properties in the boundary and/or “E.H.L (Elastohydrodynamic Lubrication)” area due to its rheological characteristics. This research evaluated HVI base stock's low-friction properties. Upgrading the oil from 5W-30 to 5W-20 was also investigated. The friction properties of the HVI base stock were measured by a unit friction platform. The results show a 28% reduction in friction coefficient compared with the conventional, solvent refined oil, which is attributable to the high-pressure viscosity of the base oil.

Gas shielded metal arc welding is generally applied to automobile chassis parts. However, the weld parts with the E-coat show poor corrosion resistance. Therefore, the corrosion mechanism of the weld parts was investigated. The results found two reasons why the weld parts corroded faster than the non weld parts:(1)inadequate phosphating (2)defects in the E-coat. After detailed investigation, it was clarified that the major cause of poor corrosion resistance was the defects in the E-coat caused by slags formed on the surface of the weld bead. Therefore the amount of slag has to be decreased to improve the corrosion resistance. The effect of shielding gas composition on the amount of slag was then investigated. In the case of Ar and oxidizing gas mixture, the corrosion resistance improved as the oxidizing gas content decreased. This was due to the reduction of slags.

The use of low-density materials in body panels is increasing as a measure to reduce the weight of the vehicle body. Honda has developed an aluminum/steel sheet hybrid door that is more effective in reducing weight than an all-aluminum door. Because aluminum was used in the door skin, bimetallic corrosion at the connection between the aluminum and the steel sheets represented an issue. It was possible that the difference in the electrical potential of the two metals might promote corrosion at the connection between the aluminum door skin and the steel sheet door panel, in particular at the lower edge of the door, where rainwater and other moisture tend to accumulate, with the result that the appeal of the exterior of the door might decline.

The technology for a new, high-strength piston material has been developed by using high pressure die casting (HPDC) method, which had a rapid rate of solidification. This method allowed the amount of Ni added to be increased to 5.5 mass%, raising the fatigue strength of the new material at temperatures of 523 K or higher by a factor of 1.5 over that of a conventional material made by gravity die casting (GDC). In addition, application of vacuum to the die cavity and using additional pressure enabled quality exceeding that of conventional GDC pistons. Pistons made from the newly developed material decreased engine friction by 4.4% and increased fuel efficiency by 2.2% in engine bench testing.

The two liter DOHC-VTEC engine developed for the Honda S2000 produces 179kW (240HP, which is 120HP per liter). It is the highest output power among all naturally aspirated two liter engines ever mass-produced. It also achieves an exhaust emission level within National LEV standards. The new engine utilizes a redesigned VTEC cylinder head, in which MIM (metal injection molding) rocker arms are used. The new cylinder block with a ladder frame structure for its lower part, a newly developed camshaft drive chain and gear system and a metal honeycomb catalyst with an air pump start-up system are also utilized.

Recently, much research has been carried out on secondary O2 feedback which performs control based on the output from a secondary O2 sensor (HEGO sensor). In this research it has been found that, regardless of catalyst aging conditions, the HEGO sensor output indicates 0.6 V when the catalyst reduction rate is maintained at the optimum level. Therefore, based on this relationship, we designed an accurate secondary O2 feedback with the aim of reducing emissions by stabilizing the HEGO sensor output to 0.6 V. In order to realize this control, it was necessary to solve the three problems of nonlinear catalyst characteristics, dead time characteristics, and changes in dynamic characteristics due to catalyst aging conditions. Therefore, these problems were solved using the modeling approach of robust control and a new robust adaptive control named Prediction and Identification Type Sliding Mode Control.

In general, welding of high-pressure die casting (DC) parts has been difficult due to gases trapped in the castings. This is a result of the high-speed turbulent flow condition of the DC process. These gases are liberated during welding and produce porosity in the weld joint. The Author had found the range where an enough welding quality was obtained without great drop in castability to the middle of the laminar flow and turbulent flow. This range has been defined as the transition zone. Moreover high strength Al-Mg-Ni alloy was developed by non-heat-treatment. The Transition Flow Filling Method(TFFM) has been developed, that can not only reduce the amount of trapped gases but also is applicable to standard high pressure die casting equipment. With this method, high quality DC parts can be produced that are weldable, strong and have high toughness.