Search Results

This research was to model a 6×4 tractor-trailer rig using TruckSim and simulate severe braking maneuvers with hardware in the loop and software in the loop simulations. For the hardware in the loop simulation (HIL), the tractor model was integrated with a 4s4m anti-lock braking system (ABS) and straight line braking tests were conducted. In developing the model, over 100 vehicle parameters were acquired from a real production tractor and entered into TruckSim. For the HIL simulation, the hardware consisted of a 4s4m ABS braking system with six brake chambers, four modulators, a treadle and an electronic control unit (ECU). A dSPACE simulator was used as the “interface” between the TruckSim computer model and the hardware.

A variety of methodologies to use embedded multicore controllers efficiently has been discussed in the last years. Several assumptions are usually made in the automotive domain, such as static assignment of tasks to the cores. This paper shows an approach for efficient task allocation depending on different system modes. An engine management system (EMS) is used as application example, and the performance improvement compared to static allocation is assessed. The paper is structured as follows: First the control algorithms for the EMS will be classified according to operating modes. The classified algorithms will be allocated to the cores, depending on the operating mode. We identify mode transition points, allowing a reliable switch without neglecting timing requirements. As a next step, it will be shown that a load distribution by mode-dependent task allocation would be better balanced than a static task allocation.

A multi-point hypoid gear mesh model based on 3-dimensional loaded tooth contact analysis is incorporated into a coupled multi-body dynamic and vibration hypoid gear model to predict more detailed dynamic behavior of each tooth pair. To validate the accuracy of the proposed model, the time-averaged mesh parameters are applied to linear time-invariant (LTI) analysis and the dynamic responses, such as dynamic mesh force, dynamic transmission error, are computed, which demonstrates good agreement with that predicted by single-point mesh model. Furthermore, a nonlinear time-varying (NLTV) dynamic analysis is performed considering the effect of backlash nonlinearity and time-varying mesh parameters, such as mesh stiffness, transmission error, mesh point and line-of-action. Simulation results show that the time history of the mesh parameters and dynamic mesh force for each pair of teeth within a full engagement cycle can be simulated.

As the original engine sound is usually not enough to satisfy the driver’s desire for a sporty and fascinating sound, Active Noise Control (ANC) and Active Sound Design (ASD) have been great technologies in automobiles for a long time. However, these technologies which enhance the sound of vehicles using loud speakers or electromagnetic actuators etc. lead to the increase of cost and weight due to the use of external amplifiers or actuators. This paper presents a new technology for generating a target sound by the active control of a permanent magnet synchronous motor (PMSM) of a mass-production steering system. The existing steering hardware or motor is not changed, but only additional software is added. Firstly, an algorithm of this technology, called Active Sound Generation (ASG), is introduced which is compiled and included in the ECU target code. Then the high frequency noise issue and its countermeasures are presented.

Due to the design of lightweight, high speed driveline system, the coupled bending and torsional vibration and rotordynamics must be considered to predict vibratory responses more realistically. In the current analysis, a lumped parameter model of the propeller shaft is developed with Timoshenko beam elements, which includes the effect of rotary inertia and shear deformation. The propeller shaft model is then coupled with a hypoid gear pair representation using the component mode synthesis approach. In the proposed formulation, the gyroscopic effect of both the gear and propeller shaft is considered. The simulation results show that the interaction between gear gyroscopic effect and propeller shaft bending flexibility has considerable influence on the gear dynamic mesh responses around bending resonances, whereas the torsional modes still dominate in the overall frequency spectrum.

Modeling of elastohydrodynamic lubrication phenomena for the spiral bevel gears is performed in the present study. The damping and the friction coefficient generated from the lubricated contact area will have profound effects on the dynamics of spiral bevel gears. Thus the damping value generated from this friction model will be time varying. This makes the use of constant and empirical damping value in the dynamics of spiral bevel gears questionable. The input geometric and kinematic data required for the elastohydrodynamic lubrication (EHL) simulations are obtained using Tooth Contact Analysis. A full numerical elastohydrodynamic lubrication simulations are carried out using asymmetric integrated control volume (AICV) algorithm to compute the contact pressures. The fast Fourier transform is used to calculate the elastic deformations on the gear surfaces due to contact load.

This paper describes an active sound tuning (AST) system for vehicle powertrain response. Instead of simply aiming to attenuate cabin interior noise, AST system is capable of reshaping the powertrain response based on predetermined vehicle sound quality criteria. However, conventional AST systems cannot yield a balanced result over the broad frequency range when applied to powertrain noise. It is due to the fact that existing systems are typically configured with the filtered-x least mean square (FXLMS) algorithm or its modified versions, which has inherent frequency dependent convergence behavior due to large dynamic range of secondary path (the electro-acoustic path from the control speaker to the error microphone). Therefore, fast convergence can only be reached at the resonant frequencies.

Current powertrain active noise control (ANC) systems are not sufficient enough to track the fast engine speed variations, and yield consistent convergence speeds for individual engine order such that a balanced noise reduction performance can be achieved over a broad frequency range. This is because most of these ANC systems are configured with the standard filtered-x least mean squares (FxLMS) algorithm, which has an inherent limitation in the frequency-dependent convergence behavior due to the existence of secondary path model (electro-acoustic path from the input of control loudspeaker to the output of monitoring error microphone) in the reference signal path. In this paper, an overview is given first to compare several recently modified FxLMS algorithms to improve the convergence speed for harmonic responses such as eigenvalue equalization FxLMS (EE-FXLMS) and normalized reference LMS (NX-LMS) algorithms.

Active noise control systems have been gaining popularity in the last couple of decades, due to the deficiencies in passive noise abatement techniques. In the future, a novel combination of passive and active noise control techniques may be applied more widely, to better control the interior sound quality of vehicles. In order to maximize the effectiveness of this combined approach, smarter algorithms will be needed for active noise control systems. These algorithms will have to be computationally efficient, with high stability and convergence rates. This will be necessary in order to accurately predict and control the interior noise response of a vehicle. In this study, a critical review of the filtered-x least mean square (FXLMS) algorithm and several other newly proposed algorithms for the active control of vehicle powertrain noise, is performed. The analysis examines the salient features of each algorithm, and compares their system performance.

In order to extend the operability limit of the gasoline compression ignition (GCI) engine, as an avenue for low temperature combustion (LTC) regime, the effects of parametric variations of engine operating conditions on the performance of six-stroke GCI (6S-GCI) engine cycle are numerically investigated, using an in-house 3D CFD code coupled with high-fidelity physical sub-models along with the Chemkin library. The combustion and emissions were calculated using a skeletal chemical kinetics mechanism for a 14-component gasoline surrogate fuel. Authors’ previous study highlighted the effects of the variation of injection timing and split ratio on the overall performance of 6S-GCI engine and the unique mixing-controlled burning mode of the charge mixtures during the two additional strokes. As a continuing effort, the present study details the parametric studies of initial gas temperature, boost pressure, fuel injection pressure, compression ratio, and EGR ratio.

High speed, precision geared rotor systems are often plagued by excessive vibration and noise problems. The response that is primarily excited by gear transmission error is actually coupled to the large displacement rotational motion of the driveline system. Classical pure vibration model assumes that the system oscillates about its mean position without coupling to the large displacement motion. To improve on this approach and understanding of the influences of the dynamic coupling, a coupled multi-body dynamic and vibration simulation model is proposed. Even though the focus is on hypoid geared rotor system, the model is more general since hypoid and bevel gears have more complicated geometry and time and spatial-varying characteristics compared to parallel axis gears.

This paper discusses an enhanced active vibration control concept to suppress the dynamic response associated with gear mesh frequencies. In active control application, the control of dynamic gear mesh tonal response is essentially the rejection or suppression of periodical disturbance. Our active control experimental work shows that the existence of un-controlled harmonic result in the increase at these harmonics when applying direct control to the target mesh frequencies. To address this problem, the effect of the existence of un-correlated harmonic components in error signal when applying active control to suppress the target gear mesh harmonics is examined. The proposed adaptive controller that is designed specifically for tackling gear mesh frequency vibrations is based on an enhanced filtered-x least mean square algorithm (FXLMS) with frequency estimation to synthesize the required reference signal.

Supervisory control strategy of a hybrid electric vehicle (HEV) provides target powers and operating points of an internal combustion engine and an electric motor. To promise efficient driving of the HEV, it is needed to find the proper values of control parameters which are used in the strategy. However, it is very difficult to find the optimal values of the parameters by doing experimental tests, since there are plural parameters which have dependent relationship between each other. Furthermore variation of the test results makes it difficult to extract the effect of a specific parameter change. In this study, a model based parameter optimization method is introduced. A vehicle simulation model having the most of dynamics related to fuel consumption was developed and validated with various experimental data from real vehicles. And then, the supervisory control logic including the control parameters was connected to the vehicle model.

A vehicle drifts due to several reasons from its intended straight path even in the case of no steering input. The multibody dynamic analysis of vehicle drift during accelerating and braking are performed. This paper focuses on modeling and evaluating effects of suspension parameters, differential friction, engine mounting and C.G. location of the vehicle under multibody dynamic simulation environment. Asymmetry of geometry and compliance between left and right side is considered cause of drift. The sensitivities of the suspension parameters are presented for each driving condition. In case of acceleration, the interaction of differential friction and driveshaft stiffness and their influence on drift are also studied. For braking condition, suspension parameters such as initial toe variation of rear coupled torsion beam axle type suspension and kingpin inclination deviation of front suspension are studied including the braking force difference.

Air conditioning is defined as the process of treating air so as to control simultaneously its temperature, humidity, cleanliness and distribution to meet the requirements of the conditioned space. As in the definition, the important actions involved in the operation of an air conditioning system are temperature and humidity control, air purification and movement. For these conditions this paper proposes a Automatic Climate Control(ACC) system of the bus. The system has cooling, heating, and dehumidifying modes, and is governed by dual 8-bit microprocessors. These modes are broken down into sub-modules dealing with control of the compressor, blower speed, damper position, air purifier, ventilators, preheater, air mixing damper and so on.

In contrast to the other types of crash simulations, integrated analysis is needed to perform the side impact simulation, and the acquired injury values are so sensitive that they are difficult to assess by the deformed vehicle structure itself. Accurate FE Euro-side impact dummy (EURO-SID) model is needed to predict the various injury values in Euro side-impact simulation. In the past, rigid body model and coarse FE model have been used. The advantage of these models is low computing power. By the way, they have lack of injury predictability in integrated simulations. The deviations are caused by inaccurate geometry and improper material characteristics expression for individual components. Therefore, new Euro side-impact dummy model is developed through mass (inertia), component and sled validation. In this paper, validation results are illustrated, and their application results in two kinds of full car simulations are introduced.

Low-pressure molding compound (LPMC) is a new kind of composite material which can be used for automotive body panels. LPMC has similar mechanical properties compared to conventional sheet molding compound (SMC) but excellent moldability due to the different thickening system. In this paper, we prepared LPMC hood prototype for a passenger car using a low-cost tooling. Inner panel and outer panel were made of general-density- and low-density-grade LPMC, respectively, in order to maximize weight reduction maintaining surface quality. Physical properties containing tensile strength, flexural modulus, notched Izod impact strength of those samples were investigated. In addition, CAE simulation was also done for strength analysis of the hood assembly.

Elastokinematic properties of the suspension system are one of major factors that improve ride and handling performances. Their properties have been quasi-statically determined using the in-door measurement device, such as the SPMD (Suspension Parameter Measurement Device). The elastokinematic properties in driving conditions, called dynamic compliance characteristics, are defined as the superposition of quasi-static properties, called static compliance characteristics. However, this superposition method has difficulties in predicting the suspension non-linearities under high lateral acceleration and transient behaviors. In this paper, dynamic compliance characteristics are directly determined through on-board measurements and transformation matrix. Their applications in validating ADAMS full vehicle model are discussed. Some experimental and simulation results about their unique properties and relationships with SPMD are presented.

Faced with the challenge to improve vehicle quality and reduce the development cycle for new product, experimental and/or analytical approach have been used to assure improvements in vehicle NVH performance. Prediction of dynamic characteristics is the most important factor to shorten development time. In order to predict car interior noise at the pre-design stage, a total vehicle without chassis parts and its cavity are fully modeled by finite elements. To reduce FE model generation time and get more effective design modification index, hybrid model combining FE data and experimental data is used. In this paper, the hybrid modeling based on FBS technique is used for identifying substructure contribution and modification. Driving force is also acquired by powertrain test. To verify this model, a passenger car is tested and compared with analysis data.

A throttle/brake control law for the intelligent cruise control (ICC) system has been proposed in this paper. The ICC system consists of a vehicle detection sensor, a controller and throttle/brake actuators. For the control of a throttle/brake system, we introduced a solenoid-valve-controlled electronic vacuum booster (EVB) and a step-motor-controlled throttle actuator. Nonlinear computer model for the electronic vacuum booster has been developed and the simulations were performed using a complete nonlinear vehicle model. The proposed control law in this paper consists of an algorithm that generates the desired acceleration/deceleration profile in an ICC situation, a throttle/brake switching logic and a throttle and brake control algorithm based on vehicle dynamics. The control performance has been investigated through computer simulations and experiments.