Search Results

The paper discusses the concept, design and final results from the ‘Ultra Boost for Economy’ collaborative project, which was part-funded by the Technology Strategy Board, the UK's innovation agency. The project comprised industry- and academia-wide expertise to demonstrate that it is possible to reduce engine capacity by 60% and still achieve the torque curve of a modern, large-capacity naturally-aspirated engine, while encompassing the attributes necessary to employ such a concept in premium vehicles. In addition to achieving the torque curve of the Jaguar Land Rover naturally-aspirated 5.0 litre V8 engine (which included generating 25 bar BMEP at 1000 rpm), the main project target was to show that such a downsized engine could, in itself, provide a major proportion of a route towards a 35% reduction in vehicle tailpipe CO2 on the New European Drive Cycle, together with some vehicle-based modifications and the assumption of stop-start technology being used instead of hybridization.

In the present study, Large Eddy Simulations (LES) have been performed with a 3D model of a step nozzle injector, using n-pentane as the injected fluid, a representative of the high-volatility components in gasoline. The influence of fuel temperature and injection pressure were investigated in conditions that shed light on engine cold-start, a phenomenon prevalent in a number of combustion applications, albeit not extensively studied. The test cases provide an impression of the in-nozzle phase change and the near-nozzle spray structure across different cavitation regimes. Results for the 20oC fuel temperature case (supercavitating regime) depict the formation of a continuous cavitation region that extends to the nozzle outlet. Collapse-induced pressure wave dynamics near the outlet cause a transient entrainment of air from the discharge chamber towards the nozzle.

Throttling loss of downsized gasoline engines is significantly smaller than that of naturally aspirated counterparts. However, even the extremely downsized gasoline engine can still suffer a relatively large throttling loss when operating under part load conditions. Various de-throttling concepts have been proposed recently, such as using a FGT or VGT turbine on the intake as a de-throttling mechanism or applying valve throttling to control the charge airflow. Although they all can adjust the mass air flow without a throttle in regular use, an extra component or complicated control strategies have to be adopted. This paper will, for the first time, propose a de-throttling concept in a twin-charged gasoline engine with minimum modification of the existing system. The research engine model which this paper is based on is a 60% downsized 2.0L four cylinder gasoline demonstrator engine with both a supercharger and turbocharger on the intake.

To reduce the fuel consumption as well as to improve the crash safety of vehicles, the usage of hot stamping parts is increasing dramatically in recent years. Aisin Takaoka has produced hot stamping parts since 2001 and has developed various technologies related to Hot Stamping. In an actual hot stamping process, parts with insufficient strength could be produced sometimes at a prototyping phase, even under the proper forming conditions. In order to understand these phenomena, in this paper, phase transformation in a boron steel 22MnB5 under various cooling rates were investigated and the effects of pre-strain conditions on the phase transformations were characterised. Uniaxial tensile specimens were stretched under isothermal conditions to different strain levels of 0-0.3, at strain rates of 0.1-5.0/s and deformation temperatures of 650-800°C.

The spray characteristics of a gasoline injector depend not only on the physics of atomization of the liquid jet on exit from the nozzle plate but also on the level of turbulence generated by the internal flow, upstream of the nozzle plate, as well as on whether cavitation arises. Measurement of the internal flow field of an injector can thus provide useful information and can assist the evaluation of the accuracy of computer predictions of the flow and associated cavitation. Information about the flow field upstream of nozzle exits is, however, rare and this forms the background to this work. Two-Dimensional Micro Particle Imaging Velocimetry (μPIV) was employed to measure the internal flow field in planes parallel to a plane of symmetry of the injector, downstream of the needle valve centring boss of a 10:1 super-scale transparent model of an 8-nozzle gasoline injector, with exit model-nozzle diameters of 2mm and a fixed model-needle lift of 0.8mm.

Bearings represent one of the main causes of friction losses in internal combustion engines, and their lubrication performance has a crucial influence on the operating condition of the engine. In particular, the conrod small-end bearing is one of the most critical engine parts from a tribological point of view since limited contact surfaces have to support high inertial and combustion forces. In this contribution an analysis is performed of the tribological behavior of the lubricated contact between the piston pin and the conrod small-end of a high performance motorbike engine. A mass-conserving algorithm is employed to solve the Reynolds equation based on a complementarity formulation of the cavitation problem. The analysis of the asperity contact problem is addressed in detail. A comparison between two different approaches is presented, the former based on the standard Greenwood/Tripp theory and the latter based on a complementarity formulation of the asperity contact problem.

Modeling plume interaction and collapse for direct-injection gasoline sprays is important because of its impact on fuel-air mixing and engine performance. Nevertheless, the aerodynamic interaction between plumes and the complicated two-phase coupling of the evaporating spray has shown to be notoriously difficult to predict. With the availability of high-speed (100 kHz) Particle Image Velocimetry (PIV) experimental data, we compare velocity field predictions between plumes to observe the full temporal evolution leading up to plume merging and complete spray collapse. The target “Spray G” operating conditions of the Engine Combustion Network (ECN) is the focus of the work, including parametric variations in ambient gas temperature. We apply both LES and RANS spray models in different CFD platforms, outlining features of the spray that are most critical to model in order to predict the correct aerodynamics and fuel-air mixing.

In Gasoline Direct Injection engines, direct exposure of the injector to the flame can cause combustion products to accumulate on the nozzle, which can result in increased particulate emissions. This research observes the impact of injector fouling on particulate emissions and the associated injector spray pattern and shows how both can be reversed by utilising fuel detergency. For this purpose multi-hole injectors were deliberately fouled in a four-cylinder test engine with two different base fuels. During a four hour injector fouling cycle particulate numbers (PN) increased by up to two orders of magnitude. The drift could be reversed by switching to a fuel blend that contained a detergent additive. In addition, it was possible to completely avoid any PN increase, when the detergent containing fuel was used from the beginning of the test. Microscopy showed that increased injector fouling coincided with increased particulate emissions.

A mixed flow turbine with pivoting nozzle vanes was designed and tested to actively adapt to the pulsating exhaust flow. The turbine was tested at equivalent speed of 48000 rpm with inlet flow pulsation of 40Hz and 60Hz, which corresponds to a 4-stroke diesel engine speed of 1600 rpm and 2400 rpm respectively. The nozzle vane operating schedules for each pulse period are evaluated experimentally in two general modes; natural opening and closing of the vanes due to the pulsating flow and the forced sinusoidal oscillation of the vanes to match the incoming pulsating flow. The turbine energy extraction as well as efficiency is compared for the two modes to formulate its effectiveness.

Spray characteristics of injectors depend on, among other factors, not only the level of turbulence upstream of the nozzle plate, but also on whether cavitation arises. "Bulk" cavitation, by which we mean cavitation which arises far from walls and thus far from streamline curvature associated with salient points on a wall, has not been investigated thoroughly experimentally and moreover it is quite challenging to predict by means of computational fluid dynamics. Information about the effect of the injector geometry on the formation of bulk cavitation and quantitative measurements of the flow field that promotes this phenomenon in gasoline injectors does not exist and this forms the background to this work. Evolution of bulk cavitation was visualized in two gasoline multi-hole injectors by means of a fast camera.

Mandated pollutant emission levels are shifting light-duty vehicles towards hybrid and electric powertrains. Heavy-duty applications, on the other hand, will continue to rely on internal combustion engines for the foreseeable future. Hence there remain clear environmental and economic reasons to further decrease IC engine emissions. Turbocharged diesels are the mainstay prime mover for heavy-duty vehicles and industrial machines, and transient performance is integral to maximizing productivity, while minimizing work cycle fuel consumption and CO2 emissions. 1D engine simulation tools are commonplace for “virtual” performance development, saving time and cost, and enabling product and emissions legislation cycles to be met. A known limitation however, is the predictive capability of the turbocharger turbine sub-model in these tools.

Internal combustion engines are routinely developed using 1D engine simulation tools. A well-known limitation is the accuracy of the turbocharger compressor and turbine sub-models, which rely on hot gas bench-measured maps to characterize performance. Such discrete map data is inherently too sparse to be used directly in simulation, and so a preprocessing algorithm interpolates and extrapolates the data to generate a wider, more densely populated map. Methods used for compressor map interpolation vary. They may be mathematical or physical in nature, but there is no unified approach, except that they typically operate on input map data in SAE format. For decades it has been common practice for turbocharger suppliers to share performance data with engine OEMs in this form. This paper describes a compressor map interpolation technique based on the nondimensional compressor flow and loading coefficients, instead of SAE-format data.

Engine stop/start and cylinder deactivation are increasingly in use to improve fuel consumption of internal combustion engine in passenger cars. The stop/start technology switches off the engine to whenever the vehicle is at a stand-still, typically in a highly-congested area of an urban driving. The inherent issue with the implementation of stop/start technology in Southeast Asia, with tropical climate such as Malaysia, is the constant demand for the air-conditioning system. This inevitably reduces the duration of engine switch-off when the vehicle at stop and consequently nullifying the benefit of the stop/start system. On the other hand, cylinder deactivation technology improves the fuel consumption at certain conditions during low to medium vehicle speeds, when the engine is at part load operation only. This study evaluates the fuel economy benefit between the stop/start and cylinder deactivation technologies for the actual Kuala Lumpur urban driving conditions in Malaysia.

The use of twin-scroll turbocharger turbines has gained popularity in recent years. The main reason is its capability of isolating and preserving pulsating exhaust flow from engine cylinders of adjacent firing order, hence enabling more efficient pulse turbocharging. Asymmetrical twin-scroll turbines have been used to realize high pressure exhaust gas recirculation (EGR) using only one scroll while designing the other scroll for optimal scavenging. This research is based on a production asymmetrical turbocharger turbine designed for a heavy duty truck engine of Daimler AG. Even though there are number of studies on symmetrical twin entry scroll performance, a comprehensive modeling tool for asymmetrical twin-scroll turbines is yet to be found. This is particularly true for a meanline model, which is often used during the turbine preliminary design stage.

Turbocharging has become the favored approach for downsizing internal combustion engines to reduce fuel consumption and CO2 emissions, without sacrificing performance. Matching a turbocharger to an engine requires a balance of various design variables in order to meet the desired performance. Once an initial selection of potential compressor and turbine options is made, corresponding performance maps are evaluated in 1D engine cycle simulations to down-select the best combination. This is the conventional matching procedure used in industry and is ‘passive’ since it relies on measured maps, thus only existing designs may be evaluated. In other words, turbine characteristics cannot be changed during matching so as to explore the effect of design adjustments. Instead, this paper presents an ‘adaptive’ matching methodology for the turbocharger turbine.

Reported in the current paper is a study into the cycle efficiency effects of utilising a complex valvetrain mechanism in order to generate variable in-cylinder charge motion and therefore alter the dilution tolerance of a Direct Injection Spark Ignition (DISI) engine. A Jaguar Land Rover Single Cylinder Research Engine (SCRE) was operated at a number of engine speeds and loads with the dilution fraction varied accordingly (excess air (lean), external Exhaust Gas Residuals (EGR) or some combination of both). For each engine speed, load and dilution fraction, the engine was operated with either both intake valves fully open - Dual Valve Actuation (DVA) - or one valve completely closed - Single Valve Actuation (SVA) mode. The engine was operated in DVA and SVA modes with EGR fractions up to 20% with the excess air dilution (Lambda) increased (to approximately 1.8) until combustion stability was duly compromised.

The Ahmed Body is one of the most widely studied bluff bodies used for automotive conceptual studies and Computational Fluid Dynamics - CFD software validation. With the advances of the computational processing capacity and improvement in cluster costs, high-fidelity turbulence models, such as Detached Eddies Simulation – DES and Large Eddies Simulation – LES, are becoming a reality for industrial cases, as studied by BUSCARIOLO et al. (2016) [4], evaluating DES models to automotive applications. This work presents a correlation study between a computational and physical model of an Ahmed Body with slant angle of 0 degree, also known as a squared back. Physical results are from a wind tunnel test, performed by STRACHAN et al. (2007) [11] considering moving ground and Reynolds number of 1.7M, based on the length of the body.

The use of twin-scroll turbocharger turbine in automotive powertrain has been known for providing better transient performance over conventional single-scroll turbine. This has been accredited to the preservation of exhaust flow energy in the twin-scroll volute. In the current study, the performance comparison between a single and twin-scroll turbine has been made experimentally on a 1.5L passenger car gasoline engine. The uniqueness of the current study is that nearly identical engine hardware has been used for both the single and twin-scroll turbine volutes. This includes the intake and exhaust manifold geometry, turbocharger compressor, turbine rotor and volute scroll A/R variation trend over circumferential location. On top of that, the steady-state engine performance with both the volutes, has also been tuned to have matching brake torque.

The implementation of Synthetic Jet Actuators (SJAs) on Unmanned Aerial Vehicles (UAVs) provides a safe test-bed for analysis of improved performance, in the hope of certification of this technology on commercial aircraft in the future. The use of high resolution numerical methods (i.e. CFD) to capture the details of the effects of SJAs on flows and on the hosting lifting surface are computationally expensive and time-consuming, which renders them ineffective for use in real-time flow control implementations. Suitable alternatives include the use of Reduced Order Models (ROMs) to capture the lower resolution overall effects of the jets on the flow and the hosting structure. This research paper analyses the effects of SJAs on aircraft wings using a ROM for the purpose of determining the unsteady aerodynamic forces modified by the presence of the SJAs. The model developed is a 3D unsteady panel code where the jets are represented by source panels.

The present work investigates the effect of low levels CO2 addition on the combustion characteristics inside a single cylinder optical engine operated under low load conditions. The effects of dilution levels (up to 7.5% mass flow rate CO2 addition), the number of pilot injections (single or double pilot injections) and injection pressure (25 or 40 MPa), are evaluated towards the direction of achieving a partially premixed combustion (PPC) operation mode. The findings are discussed based on optical measurements and via pressure trace and apparent rate of heat release analyses in a Ricardo Hydra optical light duty diesel engine. The engine was operated under low IMEP levels of the order of 1.6 bar at 1200 rpm and with a CO2 diluent-enhanced atmosphere resembling an environment of simulated low exhaust gas recirculation (EGR) rates. Flame propagation is captured by means of high speed imaging and OH, CH and C2 line-of-sight chemiluminescence respectively.