Search Results

Air motion inside the engine cylinder plays a predominant role on combustion and emission processes. An attempt has been made in this investigation to simulate the in-cylinder air motion in a DI diesel engine with four different piston configurations such as dome piston, bowl on dome and pentroof piston and pentroof offset bowl piston. For computational analysis, the commercial general purpose code STAR-CD Es-ice has been used, which works on the method of finite volume. To validate the simulation, qualitative and quantitative comparisons have been done with the PIV results available in the literature. From this study, the best possible piston configuration has been arrived at.

For controlling oxides of nitrogen (NOx) and particular matter (PM) emissions from diesel engines, various fuel and combustion mode modification strategies are investigated in the past. Low temperature combustion (LTC) is an alternative combustion strategy that reduces NOx and PM emissions through premixed lean combustion. Dual fuel reactivity-controlled compression ignition (RCCI) is a promising LTC strategy with better control over the start and end of combustion because of reactivity and equivalence ratio stratification. However, the unburned hydrocarbon (HC) and carbon monoxide (CO) emissions are significantly higher in RCCI, especially at part-load conditions. The present work intends to address this shortcoming by utilizing oxygenated alternative fuels. Considering the limited availability and higher cost, replacing conventional fuels completely with alternative fuels is not feasible.

The presence of unsaturated methyl esters in biodiesel makes it susceptible to oxidation and fuel quality degradation upon long-term storage. In the present work, the effects of oxidation of Karanja biodiesel upon long-term storage on the combustion and emission characteristics of a heavy-duty truck diesel engine are studied. The Karanja biodiesel is stored for one year in a 200 litres steel barrel at room conditions to mimic commercial storage conditions. The results obtained show that compared to diesel, the start of injection of fresh and aged biodiesels are advanced by ~2-degree crank angle, and the ignition delay time is reduced. Aged biodiesel showed a slightly smaller ignition delay compares to fresh biodiesel. The fuel injection and combustion characteristics of fresh and aged biodiesels were similar at all the load conditions. Both fresh and aged biodiesels produced higher oxides of nitrogen (NOx) and lower smoke emissions compared to diesel.

In-cylinder emission control methods for simultaneous reduction of oxides of nitrogen (NOx) and particulate matter (PM) are gaining attention due to stringent emission targets and the higher cost of after-treatment systems. In addition, there is a renewed interest in using carbon-neutral biodiesel due to global warming concerns with fossil diesel. The bi-directional NOx-PM trade-off is reduced to a unidirectional higher NOx emission problem with biodiesel. The effect of water injection with biodiesel with low water quantities is relatively unexplored and is attempted in this investigation to mitigate higher NOx emissions. The water concentrations are maintained at 3, 6, and 9% relative to fuel mass by varying the pulse width of a low-pressure port fuel injector. Considering the corrosive effects of water at higher concentrations, they are maintained below 10% in the present work.

Adopting a low compression ratio (LCR) is a viable approach to meet the stringent emission regulations since it can simultaneously reduce the oxides of nitrogen (NOx) and particulate matter (PM) emissions. However, significant shortcomings with the LCR approach include higher unburned hydrocarbon (HC) and carbon monoxide (CO) emissions and fuel economy penalties. Further, poor combustion stability of LCR engines at cold ambient and part load conditions may worsen the transient emission characteristics, which are least explored in the literature. In the present work, the effects of implementing the low compression ratio (LCR) approach in a mass-production light-duty vehicle powered by a single-cylinder diesel engine are investigated with a major focus on transient emission characteristics.

Today, GDI engines are becoming very popular because of better fuel economy and low exhaust emissions. The gain in fuel economy in these engines is realized only in the stratified mode of operation. In wall-guided GDI engines, the mixture stratification is realized by properly shaping the combustion chamber. However, the level of mixture stratification varies significantly with engine operating conditions. In this study, an attempt has been made to understand the effect of engine operating parameters viz., compression ratio, engine speed and inlet air pressure on the level of mixture stratification in a four-stroke wall-guided GDI engine using CFD analysis. Three compression ratios of 10.5, 11.5 and 12.5, three engine speeds of 2000, 3000 and 4000 rev/min., and three inlet air pressures of 1, 1.2 and 1.4 bar are considered for the analysis. The CONVERGE software is used to perform the CFD analysis. Simulation is done for one full cycle of the engine.

Today, gasoline direct injection (GDI) engine is one of the best strategies to meet the requirement of low pollutant emissions and fuel consumption. Generally, the GDI engine operates in stratified mixture mode at part-load conditions and homogeneous mixture mode at full-load conditions. But, at part-loads, soot emissions are found to be high because of improper air-fuel mixing. To overcome the above issue, a homogenous-stratified mixture (a combination of the overall homogeneous lean mixture with a combustible mixture at the location of the spark plug) is found to be better to reduce soot emissions compared to a stratified mixture mode. It will also help reduce fuel consumption. In this study, the analysis has been done to evaluate the effect of homogeneous-stratified mixture combustion on the performance and emission characteristics of a spray-guided GDI engine under various conditions using computational fluid dynamics (CFD).

For more than a decade there is a progressive demand for fuel efficient and high specific power output engines. Optimization of engine cooling and thermal management is one of the important activities in engine design and development. In the present paper an effort has been made to simulate the heat transfer modes of cylinder block and head for a present 4-stroke air-cooled motorcycle engine. Two and three-dimensional decoupled and conjugate heat transfer analysis has been done with commercially available computational fluid dynamics (CFD) codes. Experimental results are also presented. A complete simulation model has been developed and CFD techniques have been applied to design and optimize air cooling surfaces of cylinder head and block, for an air cooled motorcycle engine. The two dimensional analysis is an easy and fast method to predict fin surface temperature, heat transfer co-efficient and flow velocity.

The ride vibration environment of a typical high-speed military tracked vehicle traversing rough off-road terrain is a significant factor due to the magnitude of ride vibrations arising from dynamic terrain-vehicle interactions. In this paper, ride dynamics of a “2+N” degrees of freedom (DOF) tracked vehicle mathematical model has been evaluated for rough off-road terrain modeled as a sinusoidal profile of different pitch and height at constant running speeds. The equations of motion are derived using Newton's laws of motion. A comparison of ride dynamic analysis of the vehicle fitted with conventional passive suspension system and hydrogas suspension system is made.

Mixture distribution in the combustion chamber of gasoline direct injection (GDI) engines significantly affects combustion, performance and emission characteristics. The mixture distribution in the engine cylinder, in turn, depends on many parameters viz., fuel injector hole diameter and orientation, fuel injection pressure, the start of fuel injection, in-cylinder fluid dynamics etc. In these engines, the mixture distribution is broadly classified as homogeneous and stratified. However, with currently available engine parameters, it is difficult to objectively classify the type of mixture distribution. In this study, an attempt is made to objectively classify the mixture distribution in GDI engines using a parameter called the “stratification index”. The analysis is carried out on a four-stroke wall-guided GDI engine using computational fluid dynamics (CFD).

This paper deals with a numerical investigation on swirl generation by a helical intake port and its effects on in-cylinder flow characteristics with axisymmetric piston bowls in a small four-valve direct injection diesel engine. The novelty of this study is in determining the appropriate design and orientation of the helical port to generate high swirl. A commercial CFD software STAR-CD is used to perform the detailed three dimensional simulations. Preliminary studies were carried out at steady state conditions with the helical port which demonstrated a good swirl potential and the CFD predictions were found to have reasonably good agreement with the experimental data taken from literature. For transient cold flow simulations, the STAR-CD code was validated with Laser Doppler Velocimetry (LDV) experimental velocity components’ measurements available in literature.

The classical trade-off between NOx and soot emissions from conventional diesel engines has been a limiting factor in meeting ever stringent emission norms. The electronic control of fuel injection in diesel engines emerged as an important strategy for their simultaneous reduction. The high pressure multiple-injection in a common rail direct injection system has been promising in this regard. While, the effects of pilot injection or multiple pulses of CRDI injection schedule on simultaneous reduction of NOx and soot have been widely investigated and reported, the investigations concerning three and more injection pulses have been limited. In this paper, the ability of a predictive model, developed by the authors, in providing optimal multiple-injection schedule is demonstrated through parametric investigations. The effects of pilot and post fuel quantity and dwell between the injection pulses on NOx and soot emissions are discussed.

In this study, an attempt has been made to estimate trapping efficiency of a two-stroke engine by CFD analysis under cold flow conditions. A single-cylinder, loop-scavenged, spark-ignition, two-stroke engine extensively used for two-wheeler application in India is being considered for the analysis. Engine geometry is modeled using commercial PRO-E software. Simulation is carried out using commercial CFD code STAR-CD. The CFD predictions are validated by available experimental data. In the present study, the trapping efficiency is estimated at various engine speeds with change in configurations of ports. From the analysis of results, it is found that, increasing exhaust port area relative to total transfer port area and engine speeds increase the trapping efficiency significantly. In general, it is possible to increase the trapping efficiency by about 4% at the engine speeds considered.

Oil with high free fatty acid (FFA) content may not be an appropriate contestant for biodiesel production due to poor process yield. The high FFA content (≻1%) will cause soap formation and the separation of products will be exceedingly difficult, and as a result, it has low yield of biodiesel product. In order to increase the process yield, pretreatment setup is required. This involves additional cost and will increase overall fuel price. Hence crude vegetable oils having high FFA can be blended with diesel for effectual employment in diesel engines. In this context, Jatropha Curcas L, non-edible tree-based oil with higher FFA content, can be considered as one of the prominent blending sources for diesel. The primary objective of the present work is to analyze the effect of FFA content of crude Jatropha Curcas L oil (CJO) on performance and emission characteristics of a direct injection (DI) diesel engine.

Engine modelling aims at studying the combustion related phenomenon occurring in Internal Combustion (IC) engines. In this regard, a low dimensional mathematical model using first principles has been developed to study Spark Ignited (SI) engines. The resulting equations are Ordinary Differential Equations (ODE) (for volume, pressure, torque, speed and work done) and Partial Differential Equations (PDEs) for temperature and species conservation equations (fuel, CO, CO2, NO). This model utilizes simplified reaction kinetics for the oxidation of fuel in the combustion chamber. A two-step mechanism for the combustion of fuel and the classical Zeldovich Mechanism are used to predict the amount of NO formed during combustion. The model is solved in FORTRAN using LSODE subroutine (for stiff equations) with lumped parameters for thermal properties and diffusion, and invoking the ideal gas assumption.

In this paper, energy absorption behavior of Aluminum Alloy AA 7003 and high strength steel tubes is investigated for automotive crash application both experimentally and numerically. The compression test results are compared with the static analysis results obtained from LS-Dyna Software. Tube thickness is varied in the LS-Dyna Finite Element Simulation Software to understand its effect on energy absorption behavior. The peak loads and energy absorption between experimental results and Numeral simulation are found to be in good agreement. The specific energy absorption between high strength steel and Aluminum Alloy AA 7003 is compared.

Nowadays, Direct Injection Spark Ignition (DISI) engines are very popular because of their lower fuel consumption and exhaust emissions due to lean stratified mixture operation at most of load conditions. In these engines, achieving mixture stratification plays an important role on performance and emission characteristics of the engine. Also, mixture stratification is mainly dependent on in-cylinder flows and air-fuel interaction, which in turn largely dependent on valve configurations. Therefore, understanding them is very much essential in order to improve the engine performance. In this study, a CFD analysis has been carried out on two- and four-valve four-stroke engines to analyze in-cylinder flows and air-fuel interaction at different conditions. The engines specifications considered here are taken from the literature for which experimental data is available. ‘STAR-CD’ software has been used for the CFD analysis. For meshing, polyhedral trimmed cells have been adopted.

Direct injection diesel engines are used in both light duty and heavy duty vehicles because of higher thermal efficiency compared to SI engines. However, due to only short time available for fuel-air mixing, combustion process depends on proper mixing. As a result, DI Diesel engine emits more NOx and soot into the atmosphere. Therefore, to achieve better combustion with less emission and also to accelerate the fuel-air mixing to improve the combustion, appropriate design of combustion chamber is crucial. Hence, in this work a study has been carried out using CFD to evaluate the effect of combustion chamber configuration on Diesel combustion with two different piston bowls. The two different piston configurations considered in this study are centre bowl on flat piston and pentroof offset bowl piston.

This paper deals with in-cylinder flow field analysis in a motored two-stroke engine by CFD technique using STAR-CD. The main aim of this study is to find out the best turbulence model which predicts the fluid flow field inside the cylinder of a two-stroke engine. In this study, a single-cylinder, two-stroke engine which is very commonly used for two-wheeler application in India is considered. Entire analysis is done at an engine speed of 1500 rev/min. under motoring conditions. Here, three commonly used turbulence models viz. standard k-ε, Chen k-ε and RNG k-ε are considered. In addition, experiments were also conducted on the above engine at the motoring conditions to measure velocity vectors of in-cylinder flow fields using particle image velocimetry (PIV). The results of PIV were also used for validating the CFD predictions.

Premixed Charge Compression Ignition (PCCI) is a promising LTC strategy to reduce NOx and soot emissions without relying on after-treatment devices. One major drawback of PCCI is high HC and CO emissions resulting from fuel-wall impingement due to early injection of diesel. Narrow-angle direct injection (NADI) helps reduce the wall wetting of fuel. But it is effective only at lower loads. At mid and higher loads, it increases soot and CO emissions in small-bore engines due to the formation of fuel-rich pockets in the piston bowl region. This problem is addressed using a split injection strategy in the present work. A 3-D CFD model is developed and validated with experimental data at two load conditions. Simulations are performed using CONVERGE CFD software. Split injection strategies are explored using wide (148 deg) and narrow (88 deg) spray included angles.