Search Results

The purpose of this paper is to propose a control method to reduce acceleration shock in motorcycles. Reducing the acceleration shock is very important in improving driveability of motorcycles. Motorcycles equipped with manual transmission have some backlashes in the transmission, with large backlash especially in dog clutch portions. We have figured out that one of the main causes of the acceleration shock is the collision of the dogs at high relative angular velocity during acceleration. Also, our data analysis has revealed that there is a correlation between a peak value of the longitudinal body acceleration and the relative angular velocity at the moment of the dog collision. A simulation was undertaken to verify this phenomenon, and its results have made it clear that we need to decrease the relative angular velocity at the moment of the dog collision so as to reduce the acceleration shock.

The power train system for Utility Vehicles (UVs) or All-Terrain Vehicles (ATVs) mainly consists of a rubber V-belt CVT. The adjustment of the CVT specification requires many steps to realize the shifting operations of the CVT so as to satisfy the acceleration feeling of the driver. In this paper, we report on the simulation technology that predicts the transient behavior during an acceleration of the vehicle equipped with a belt tension clutching CVT, which has both functions of the shift operation and the clutch action. By using the developed simulation technique, it has become possible to adjust the CVT specifications efficiently.

This paper describes a simulation of the lubricating oil flow in a motorcycle oilpan using a CFD technique in consideration of oil suction and oil return. In the technique, sink boundary and source boundary were used to simulate oil suction and oil return, and a VOF method was used to simulate the free surface of oil. To validate the simulation, a simulation result was compared with experiment results of a prototype motorcycle. As a result, the time of the simulated oil pressure drop in main gallery when the motorcycle decelerated rapidly in a racing circuit was agreed with the measured one. In addition, to demonstrate the applicability of the CFD simulation, a case study of the shape optimization on the baffle plate in the oilpan was shown.

This paper describes a numerical analysis method for predicting the brake squeal using the Substructure Synthesis Method. This method is more accurate than the classical method based on the mass-spring system, and simpler than the analysis of all the brake system by FEM. The squeal studied here is focused the one occurring in the low frequency range and its mechanism is due the structural instability of the brake assembly. First, some experiments were carried out in order to grasp the brake squeal phenomenon. These experiments made clear the following items. (1) The low frequency brake squeal occurred at 850Hz. (2) The vibration mode shape had 5 nodes fixed in a space. (3) The brake squeal became maximum at 0.3 - 0.5 (MPa) liquid pressure under the constant temperature condition. (4) The higher the temperature of the pad was, the stronger the brake squeal was under the constant liquid pressure condition.

Motorcycle engines are operated at an extremely broad range of revolutions, from 1000 min-1 to 10000 min-1 or more. Ideally, the natural frequency of each part should never match the engine excitation frequency at any point over that entire range of revolution speeds, but practically, there are times when resonance cannot be avoided because the range is so broad, and therefore the vibration amplitude at resonance must be kept low. For this reason, it is important to grasp not only the resonance frequency but also the vibration amplitude at that point. This may be achieved by two methods, measurement and analysis. The direct measurement of vibration is generally difficult because the motorcycle muffler system has a complex shape and in addition it gets very high temperature when the engine is operating. For this reason, with the aim of being able to predict muffler vibration at the design stage, we carried out a vibration test and FEM (finite element method) analysis.

Owing to the recent developments in sensors with reduced size and weight, it is now possible to install sensors on a body of a motorcycle to monitor its behavior during running. The analysis of maneuverability and stability has been performed based on the data resulted from measurements by these sensors. The tire forces and moments is an important measurement item in maneuverability and stability studies. However, the tire forces and moments is difficult to measure directly, therefore, it is a common practice to measure the force and the moment acting on the center of the wheel. The measuring device is called a wheel forces and moments sensor, and it is widely used for cars. The development of a wheel forces and moments sensor for motorcycles has difficulty particular to motorcycles. First, motorcycles run with their bodies largely banked, which restricts positioning the sensors.

In this study, we efficiently predict the vibration response of a design shape at a low computational cost in the early development stage, select design proposals with good characteristics from many proposals devised by the designer at the early stage, and forward them to the next stage to achieve the front-loading of development while increasing product value. The application of participation factor (PF) focusing on the response at a specific part for vibration evaluation of a motorcycle frame is described. To reduce the motorcycle frame vibration, an eigenvalue analysis was performed, and appropriate design change proposals were efficiently selected using partial participation factor (PPF), an index showing the relevance of vibration of specific parts or positions. Using the PPF, we extracted which vibration modes considerably contribute to the vibration response of the part of interest.

The engine noise accounts for a relatively large percentage among the noises generated by a motorcycle. Among the parts of the engine, the cover is important in design as well as a source of the engine noise, being at the end of the vibration transfer path. This paper clarifies that the natural frequency of the cover with a flat surface clearly affects its vibration and noise radiation and that its vibration depends on this surface, by investigation of the effect of surface shape of the cover on its vibration and noise radiation and by a modal analysis of its vibration characteristics. In addition, we confirmed that the calculated value of the radiated noise from the cover agrees well with the measured value.

A new 0.9-liter 4-valve-per-cylinder liquid cooled engine was developed for 1984 model motorcycles. This new engine was optimized from the standpoint of performance, durability, and weight efficiency. Semi-Flat slide carburetors, high compression ratio, relatively short stroke and large valves were employed. This engine was upgraded every other year with changes in displacement. Induction system, exhaust system, and valve train. This paper describes, from the viewpoint of the designer, the evolution of the 4-valve liquid-cooled engine from the 1984 to 1988 models. In that evolutionary process we employed: (1) semi-down draft carburetors with smooth air ducts, (2) a computer-aided intake and exhaust port design and manufacturing system. (3) individual rocker arms. (4) a cool air intake system. (5) lightweight pistons. (6) angle -controlled tightening of connecting rod bolts.

This paper describes the predicted results of acoustic transmission loss (T.L.) for a motorcycle muffler. First, the T.L. of a prototype muffler with one expansion chamber was obtained by measuring sound levels at the inlet and outlet ports of the muffler by speaker test. T.L. was then calculated by using a three-dimensional Finite-Element Method (FEM) for acoustic fields in the muffler. There was good coincidence between the calculated T.L. and experimentally observed data. Second, T.L. of the prototype muffler while attached to a motorcycle engine was measured. On this step, however, a similarly calculated T.L. using FEM to consider the effect of exhaust gas temperature in the muffler showed differences from the measured one. It was estimated that muffler body vibration sounds may affect the result. A dynamic analysis of the structure was carried out using FEM to obtain the eigen modes of the muffler body.

With an increasing number of vehicles, the reduction of traffic noise emissions becomes a greater social requirement. On the other hand, as users' tastes for motorcycles have diversified, it becomes important to develop and supply products to meet customers' requests within a short period. Therefore, it is a key factor to efficiently develop motorcycles which conform to the noise regulations. This paper describes concrete examples of currently utilized noise-source proving methods and noise reduction methods for motorcycles.

A waterjet propulsor has come to be used more popularly for high speed watercrafts such as personal watercrafts. The most difficult problem for designing the waterjet system is that a tradeoff is required to properly determine the best parameters for the waterjet pump and subsequently the best overall propulsion system. This paper presents the design method and performance improvement of the waterjet propulsor used for personal watercrafts. The authors have clarified the performance of the individual component in the waterjet propulsor and improved the component efficiency empirically, and established the method to estimate the thrust and power characteristics of the propulsor on board from the component test results and other design parameters, which enables the optimization of the waterjet system.

Though most street-use motorcycles are now equipped with 4-stroke engines, off-road motorcycles, especially moto-cross racers, still mainly use 2-stroke engines because of their high power and light weight. 2-stroke engines for moto-cross racers require the engine characteristics of high power and excellent throttle response on a wide range of engine speeds. These characteristics immediately require an effective exhaust device to improve output performance at the middle-speed range while maintaining high power at the high-speed range. The latest 2-stroke engines maintain such performance by using an exhaust device, and also by the application of extensively improved basic elements such as the scavenging passage arrangement, exhaust timing and passage shape, etc. This paper briefly summarizes continuous efforts for the improvement of our exhaust-system device from its beginning until the present.

We developed the motorcycles based on RIDEOLOGY (Ride + Ideology) concept. In the past, the “Ride” was studied by a sensory evaluation with actual driving. However, the recent progress in numerical analysis, there have been developed driving simulators. It allows more quantitative measurement in a sensory evaluation. Therefore, we also developed a riding simulator specialized for motorcycles. In order to develop such riding simulator, there are some technical challenges for motorcycles. First, we need to reproduce roll motion height of motorcycles. Compared to four-wheeled vehicles, motorcycles have a higher center of rotation. Second, we need to reproduce vehicle motion control by rider’s changing body position. A rider controls vehicle’s lean by shifting his center of gravity. Therefore, it is necessary to construct a measurement system of rider’s body position. Third, we need to improve senses of speed and reality.

As for automobile, the mass production period of Electric Vehicle(EV) has begun by the rapid progress of the battery performance. But for EV-Motorcycle(MC), it is limited for the venture companies' releases. The design and evaluation methodologies are not yet established or standardized so far. This paper provides the practical and the experimental examples. To study the feasibility of EV-MC, we developed the prototypes in the present technical and suppliers' parts environments, and evaluated them by the practical view of the MC usage. The developed EV-MC has the equivalent driving performance of the 250cc internal combustion engine(ICE)-MC and a cruising range of 100km in normal use.

As for automobile, the mass production period of Electric Vehicle(EV) has begun by the rapid progress of the battery performance. But for EV- Motorcycle(MC), it is limited for the venture companies' releases. The design and evaluation methodologies are not yet established or standardized so far. This paper provides the practical and the experimental examples. To study the feasibility of EV-MC, we developed the prototypes in the present technical and suppliers' parts environments, and evaluated them by the practical view of the MC usage. The developed EV-MC has the equivalent driving performance of the 250cc internal combustion engine(ICE)-MC and a cruising range of 100km in normal use. In the prototype development, the reliability and the ability of protection design of the battery in the whole vehicle against the environmental loads are mainly studied, especially, heat and cold, water, shock, and the accident impact.

In line with the increase in the output of motorcycle engines, there has been an increase in incidents of the seizure between shift fork and gear because of the increased thrust force. We designed a test method that uses actual shift forks to simulate actual sliding conditions, then used that test method to evaluate the feature of the shift fork sliding and the different shift fork surface treatments. The shift fork slid against the gear not as surface contact but as tilted contact. We selected the candidates from the view that the surface treatment of the shift fork contact surface to give it higher seizure resistance when in tilted contact is required. We evaluated chromium nitride thin film, diamond-like carbon thin film, molybdenum sprayed coating, and sulphonitriding, and molybdenum sprayed coating exhibited the highest seizure resistance. The conformability plays a significant role in the sliding between the shift fork and the gear.

Motorcycle engines are required to have high output levels but low exhaust gas emission levels. Measuring the combustion condition proves useful for understanding the engine's operating condition. We developed a compact, high-performance combustion analyzer for measuring the combustion condition of motorcycle engines. This newly developed combustion analyzer is capable of analyzing the indicated mean effective pressure at each engine cycle at the engine speeds exceeding 10,000 rpm required of a high-performance motorcycle engine. Its compact size makes it easily applicable for onboard use, allowing measurement in any operating condition, including circuit travel, which has never been possible with conventional combustion analyzers. We used this new combustion analyzer to measure combustion condition not only on a chassis dynamo but also during circuit travel, when the motorcycle and engine are subjected to much harsher operating conditions.

Motorcycle configurations, such as CG (center of gravity) location, have come to be fixed to the current ones by trial and error since motorcycle was born. Generally motorcycles' ratio of CG height to wheelbase is relatively higher than four-wheel cars'. We have analyzed the optimal motorcycle CG location with relatively simple formulas, which we have derived to calculate the maximum acceleration with three performance limitations and calculate the maximum speed and the shortest time to run through a course. The results show that the calculated speed is significantly close to actual sport motorcycle's and that the optimal CG locations for various courses are bounded in a certain limited area which is near actual sport motorcycle's.

In recent years, even motorcycles impose demands for engine power controls that are more flexible and precise. The Electronic Throttle Control (ETC) system is one of the methods that addresses this need. However, the most important issue facing the installation of the ETC system on the motorcycle is handling failures. To avoid this problem, we developed an ETC system for motorcycles that can properly effect engine power control in case of a failure. This ETC system contains in duplicate the major components to detect failures and switch to a failure mode properly. To effect control that is optimally suited to the type of failure, this system switches between three types of failure modes. These failure modes are designed to minimize risks in case of a failure and maximize the operational capability while the rider is on the way to have the motorcycle repaired.