Search Results

The combustion and exhaust emission characteristics of a DME fueled HCCI engine were investigated. Different fuel injection strategies were tested under various injection quantities and timings with exhaust gas recirculation (EGR). The combustion phase in HCCI was changed by an in-cylinder direct injection and EGR, due to changes in the in-cylinder temperature and mixture homogeneity. The gross indicated mean effective pressure (IMEPgross) increased and the hydrocarbon (HC) and carbon monoxide (CO) emissions decreased as the equivalence ratio was augmented. The IMEPgross with direct injection was greater than with the port injection due to retarded ignition timing resulting from latent heat of direct injected DME fuel. It was because that most of burn duration was completed before top dead center owing to higher ignitability for DME with high cetane number. However, HC and CO emissions were similar for both injection locations.

The vast stores of biomass available worldwide have the potential to displace significant amounts of petroleum fuels. Fast pyrolysis of biomass is one of several possible paths by which we can convert biomass to higher value products. Pyrolysis oil (PO) derived from wood has been regarded as an alternative fuel to be used in diesel engines. However, the use of PO in a diesel engine requires engine modifications due to the low energy density, high acidity, high viscosity, and low cetane number of PO. Therefore, PO should be blended or emulsified with other fuels that have a high cetane number or used through pilot injection. PO has poor miscibility with light petroleum fuel oils; the most suitable candidate fuels for direct fuel mixing are alcohol fuels. Early mixing with alcohol fuels has the added benefit of significantly improving the storage and handling properties of the PO.

Characteristics of syngas combustion at various reforming ratios were studied numerically. The syngas was formed by the partial oxidation of methane to mainly hydrogen and carbon monoxide and cooled to ambient temperature. Stiochiometric and lean premixed flames of the mixtures of methane and the syngas were compared at the atmospheric temperature and pressure conditions. The adiabatic flame temperature decreased with the reforming ratio. The laminar burning velocity, however, increased with the reforming ratio. For stretched flames in a counterflow, the high temperature region was broadened with the reforming ratio. The maximum flame temperature decreased with the reforming ratio for the stoichiometric case, but increased for the lean case except for the region of very low stretch rate. The extinction stretch rate increased with the reforming ratio, implying that the syngas assisted flame is more resistance to turbulence level.

Various alternative diesel fuels such as gas to liquid (GTL) fuels, blends of diesel and biodiesel (D + BD20), and blends of GTL and biodiesel (G + BD20) were tested in a 2.0 L four-cylinder turbocharged diesel engine. A noticeable reduction in exhaust emissions as compared to diesel fuel, except for NOx emissions, was observed by blending biodiesel with diesel and GTL fuel under selected part load conditions. There was a maximum reduction of 33% for THC emissions and 27% for CO emissions for G + BD20 fuel as compared to diesel fuel. For PM size distributions, a noticeable decrease in the PM number concentration for all particle sizes less than 300 nm was observed with the blending of biodiesel. In contrast, there was a slight increase in the number concentration of PM with diameters of less than 50 nm for the cases of EGR. In the case of particulate matter (PM) mass concentration, there were reductions of 31~59% for D + BD20 fuel and 57~71% for G + BD20 fuel.

Combustion and emission characteristics of LPG(Liquefied Petroleum Gas) and gasoline fuels were compared in a single cylinder engine with direct fuel injection. While fuel injection pressure and IMEP(indicated mean effective pressure) were varied with 60, 90, 120 bar and 2 to 10 bar, another parameters for the engine operation as engine speed, air excess, and fuel injection timing were fixed at 1500 rpm, 1.0, and BTDC 300 CA respectively. Experimental results showed that MBT timing for LPG was less sensitive to IMEP, and high injection pressure made combustion stability worse at IMEP=2 bar. Through heat release analysis LPG showed shorter 10 and 90% MBD(mass burn duration) than gasoline due to fast flame speed and for both fuels injection pressure hardly affected burn duration. It was also found that thermal efficiency of LPG had a little higher than that of gasoline. Hydrocarbon emissions of gasoline rose to a level of three-fold than those of LPG.

Owing to the presence of oxygen atoms in biodiesel, the use of this fuel in compression ignition (CI) engines has the advantage of reducing engine-out harmful emissions. In this context, biodiesel fuel can also be used to extend the low temperature combustion (LTC) regime because it inherently suppresses soot formation within the combustion chamber. Therefore, in this study, LTC characteristics of biodiesel were investigated in a single cylinder CI engine; the engine performance and emission characteristics with biodiesel and conventional petro-diesel fuels were evaluated and compared. A modulated kinetics (MK)-like approach was employed to realize LTC operation. The engine test results showed that LTC operation was achieved by retardation of the fuel injection timing. The results also showed that using biodiesel reduced smoke, THC, and CO emissions but increased NOx emissions.

Because of the concerns regarding global warming caused by greenhouse gases and the high cost of fossil fuels, research on improving the fuel economy and emissions in internal combustion engines has become important. Specifically for spark ignition engines, lean-burning direct injection is the most promising technology because the fuel economy and emissions can be improved using a stable combustion of a stratified mixture. This study aimed to develop a spray-guided, lean-burning liquefied petroleum gas (LPG) direct injection engine through optimizing the combustion parameter controls. In previous research, the brake thermal efficiency in an LPG direct injection engine was significantly increased and stable combustion was secured with an interinjection spark ignition (ISI) strategy under low-load operating conditions.

Natural gas produced from coal or biomass is known as synthetic natural gas (SNG), which is expected to replace compressed natural gas (CNG). In this study, we used an 11-l heavy-duty CNG engine in a feasibility study of SNG. SNG, which is composed of 90.95% methane, 6.05% propane, and 3% hydrogen, was produced for the experiment and used as fuel to estimate its effects on combustion and emission characteristics. The torque, fuel flow rate, efficiency, fuel consumption, combustion stability, combustion phase, and emissions characteristics obtained using SNG were compared to those obtained using CNG in an engine speed range of 1,000-2,100 rpm under full load conditions. In addition, an engine fueled with SNG was given an overall evaluation using the World Harmonized Stationary Cycle (WHSC) emission test. The engine's knock characteristic was analyzed at 1,260 rpm under a full load condition. The results showed that there was no difference in power output.

Plasma burner of a new concept is suggested, developed and characterized as a unique SCR catalyst warm-up technology. This study shows a promising potential of using a plasma burner for rapid warm-up performance, minimizing fuel consumption and maximizing flame stability regardless of the temperature, oxygen concentration and flow velocity of exhaust gas in diesel engines. Since the oxygen and fuel source of the plasma burner are separated from the exhaust gas line, the performance of the plasma burner can be used regardless of engine conditions, such as engine speed and oxygen concentration. This study shows that the plasma burner can be used as an effective and promising tool for clean and energy efficient NOx and HC aftertreatment system for diesel engines.