Search Results

Inverse numerical acoustics is a method which reconstructs the source surface normal velocity from the sound measured in the near-field around the source. This is of particular interest when the source is rotating or moving, too light or too hot to be instrumented by accelerometers. The use of laser vibrometers is often of no remedy due to the complex shape of the source. The Inverse Numerical Acoustics technique is based on the inversion of transfer relations (Acoustic Transfer Vectors) using truncated Singular Value Decomposition (SVD). Most of the time the system is underdetermined which results in a non unique solution. The solution obtained by the truncated SVD is the minimal solution in the RMS sense. This paper is investigating the impact of non homogeneities in the mesh density (local mesh refinement) on the retrieved solution for underdetermined systems. It will be shown that if transfer quantities are inverted as such, big elements get a higher weight in the inversion.

Impact noise, inside a car, due to tire-launched gravel on the road can lead to loss of quality perception. Gravel noise is mainly caused by small-sized particles which are too small to be seen on the road by the driver. The investigation focuses on the identification of the mechanisms of excitation and transfer. The spatial distribution of the particles flying from a tire is determined, as well as the probable impact locations on the vehicle body-panels. Finally the relative noise contributions of the body-panels are estimated by adding the panel-to-ear transfer functions. This form of Transfer-Path-Analysis allows vehicle optimization and target setting on the level of the tires, exterior panel treatment and isolation.

This paper presents four methodologies for modeling gear mesh excitations in simple and compound planetary gear sets. The gear mesh excitations use simplified representations of the gear mesh contact phenomenon so that they can be implemented in a numerically efficient manner. This allows the gear mesh excitations to be included in transmission system-level, multibody dynamic models for the assessment of operating noise and vibration levels. After presenting the four approaches, a description is made regarding how they have been implemented in software. Finally, example models are used to do a comparison between the methods

While CAE methods allow improving nominal product design using virtual prototypes, uncertainty and variability in properties and manufacturing processes lead to scatter in actual performances. Uncertainty must hence be incorporated in the CAE process to guarantee the robustness and reliability of the design. This paper presents an overview of uncertainty-based design in automotive and aerospace engineering. Fuzzy methods take uncertainty into account, whereas reliability analysis and a reliability-based design optimization framework can deal with variability. Key enabling technologies to alleviate the computational burden, such as workflow automation, substructuring and design of experiments, are discussed, and industrial applications are presented.

The firewall design of a BMW1 is optimized for interior noise and weight using a Hybrid Interior Noise Synthesis (HINS) approach. This method associates a virtual firewall with a test based body model. A vibro-acoustic model of the firewall panel, including trim elements and full vehicle boundary conditions, is used for predictions in the 40 Hz - 400 Hz range. The short calculation time of this set-up allows multiple design iterations. The firewall noise is reduced by 0.9 dB and its mass by 5.1% through structural changes. Crashworthiness is maintained at its initial level using advanced steel processing. The total interior noise shows improvement in the 90 Hz - 140 Hz range.

This paper presents a CAE based approach to accurately simulate and optimize Ride and Handling metrics. Because of the wide range of vehicle phenomena involved, across the variety of frequency ranges, it is essential that the vehicle model includes proper representation of the dynamic properties of the various subsystems (e.g. tires, steering, PT, etc.) Precise correlation between test and simulation for standalone vehicle components and systems is achieved by replicating in the MBS (Multi-body Simulation) the same tests and boundary conditions. This allows the analyst to correctly define those crucial elements and parameters which have the greatest effect on the R&H attribute to be investigated. Setting up the simulation to correctly represent only one single maneuver simulation at a time would not allow the analyst to consider how the dynamic properties of the chassis design variables should be tuned to achieve to best balance and trade-offs.

The development of new design tools to predict the vibro-acoustic behavior within the vehicle development process is of essential importance to achieve better products in an ever shorter timeframe. In this paper, an energy flow post-processing tool for structural dynamic analysis is presented. The method is based on the conversion of conventional finite element (FE) results into energy quantities corresponding with each of the vehicle subcomponents. Based on the global dynamic system behavior and local subcomponent descriptions, one can efficiently evaluate the energy distribution and analyze the vibro-acoustic behavior in complex structures. By using energy as a response variable, instead of conventional design variables as pressure or velocity, one can obtain important information regarding the understanding of the vibro-acoustic behavior of the system.

The very first step when starting an experimental modal analysis project is the definition of the geometry used for visualization of the resulting mode shapes. This geometry includes measurement points with a label and corresponding coordinates, and usually also connections and surfaces to allow a good visualization of the measured mode. This step, even if it sounds straightforward, can be quite time consuming and is often done in a rather approximate way. Photogrammetry is a technique that extracts 2D or 3D information through the process of analyzing and interpreting photographs. It is widely used for the creation of topographic maps or city maps, and more and more for quick modeling of civil engineering structures or accident reconstruction. The purpose of this paper is to evaluate the use of this technique in the context of modal testing of automotive structures.

One of the scientific fields where, for already more than 20 years, system identification plays a crucial role is this of structural dynamics and vibro-acoustic system optimization. The experimental approach is based on the “Modal Analysis” concept. The present paper reviews the test procedure and system identification principles of this approach. The main focus though is on the real problems with which engineers, performing modal analysis on complex structures on a daily basis, are currently confronted. The added value of several new testing approaches (laser methods, smart transducers…) and identification algorithms (spatial domain, subspace, maximum likelihood,..) for solving these problems is shown. The discussed elements are illustrated with a number of industrial case studies.

Source identification applied to a truck engine and using inverse numerical acoustics is presented. The approach is based on acoustic transfer vectors (ATV) and truncated singular value decomposition (SVD). Acoustic transfer vectors are arrays of transfer functions between surface normal velocity and acoustic pressure at response points. They can be computed using boundary element methods (indirect, direct or multi-domain direct formulations) or finite element methods (in physical or modal coordinates). Regularization techniques such as the so-called L-curve approach are used to identify the optimum SVD truncation. To increase the reliability of the source identification, the approach can use velocity measurements on the boundary surface as well as the standard nearfield pressure measurements. It also allows for linear or spline interpolation of the acoustic transfer vectors in the frequency domain, to increase computational speed.

“Noise and vibration are not invented here!”. Undesirable structural dynamic behaviour is normally experienced on final assemblies, by which time the underlying cause of the problem is difficult to solve intuitively. Solving the problems classically involves the partial breakdown of assemblies and the application of various structural dynamics testing and analysis procedures. Preferably, noise and vibration problems should be avoided by designing the product right the first time, by the use of various integrated analysis and testing disciplines, from the component level to the final assembly. Such an approach is referred to, in a broader sense, by trendy themes as concurrent engineering, forward engineering, simultaneous engineering.... This paper analyzes trends in analytical and experimental structural dynamics toward better integration of the various discipline oriented techniques that are currently used.

During the last ten years, there is a significant tendency in automotive design to use lower aspect ratio tires and meanwhile also more and more run-flat tires. In appropriate publications, the influences of these tire types on the dynamic loads - transferred from the road passing wheel center into the car - have been investigated pretty well, including comparative wheel force transducer measurements as well as simulation results. It could be shown that the fatigue input into the vehicle tends to increase when using low aspect ratio tires and particularly when using run-flat tires. But which influences do we get for the loading and fatigue behavior of the respective rims? While the influences on the vehicle are relatively easy to detect by using wheel force transducers, the local forces acting on the rim flange (when for example passing a high obstacle) are much more difficult to detect (in measurement as well as in simulation).

With the introduction of hybrid vehicles and the associated elimination of engine and exhaust masking noises, sounds from other sources is becoming more noticeable. Fuel tank sloshing is one of these sources. Fuel sloshing occurs when a vehicle is accelerated in any direction and can create noise that may be perceived as a quality issue by the customer. To reduce slosh noise, a fuel tank has to be carefully designed. Reduction in slosh noise using test- based methods can be very costly and timely. This paper shows how, using the combination of CFD (Computational Fluid Dynamic), FE (Finite Element) and Acoustic simulation methods, the radiated fuel tank slosh noise performance can be evaluated using CAE methods. Although the de-coupled fluid /structure interaction (FSI) method was used for the examples in this paper, the acoustic simulation method is not limited to the decoupled FSI method.

Tip-in/Tip-out of the accelerator pedal generates transient torque oscillations in the driveline. These oscillations may be amplified by P/T, suspension and body modes and will eventually be sensible at the receiver side in the vehicle, for example at the seat or at the steering-wheel. The forces that are active during this transient excitation are influenced by non-linear effects in both the suspension and the power train mounts. In order to understand the contribution of each of these forces to the total interior target response (e.g. seat rail vibration) a detailed investigation is performed. Traditional force identification methods are not suitable for low-frequent, transient phenomena like tip-in/tip-out. Mount stiffness method can not be used because of non-linear effects in the P/T and suspension mounts. Application of matrix inversion method based on trimmed body vibration transfer functions is not possible due to numerical condition problems.

Road-tire induced vibrations are in many vehicles determining the interior noise levels in (semi-) constant speed driving. The understanding of the noise contributions of different connections of the suspension systems to the vehicle is essential in improvement of the isolation capabilities of the suspension- and body-structure. To identify these noise contributions, both the forces acting at the suspension-to-body connections points and the vibro-acoustic transfers from the connection points to the interior microphones are required. In this paper different approaches to identify the forces are compared for their applicability to road noise analysis. First step for the force identification is the full vehicle operational measurement in which target responses (interior noise) and indicator responses (accelerations or other) are measured.

The present work attempts a complete noise and vibration analysis for an electric vehicle at concept stage. The candidate vehicle is the Future Steel Vehicle (FSV), a lightweight steel body with an electric motor developed by WorldAutoSteel [1,2,3]. Measurements were conducted on two small Mitsubishi vehicles that both share the same body, yet one is equipped with an internal combustion engine and the other with an electric motor. The outcome was used as a starting point to identify assets and pitfalls of electric motor noise and draw a set of Noise Vibration and Harshness (NVH) targets for FSV. Compared to a combustion engine, the electric motor shows significantly lower sound pressure levels, except for an isolated high frequency peak heard at high speeds (3500 Hz when the vehicle drives at top speed). The prominence of this peak is lowered by increased use of acoustic absorbent materials in the motor compartment.

Acoustic performance of vehicle engines is a real challenge for powertrain design engineers. Quiet engines are required to reduce noise pollution and satisfy pass-by noise regulations, but also to improve the driving comfort. Simulation techniques such as the Boundary Element Method (BEM) have already been available for some time and allow predicting the vibro-acoustic response of engines. Although the accuracy of these simulation techniques has been proven, a challenge still remains in the required computation time. Given the large amount of speeds for a full engine run-up and the need to cover a large frequency range, computation times are significant, which limits the possibility to perform many design iterations to optimize the system. In 2001, Acoustic Transfer Vectors (ATV) [1] have been presented to adequately deal with multiple rpm. The ATV provide the acoustic response for unit surface velocities and are therefore independent from the engine's actual surface vibrations.

This paper presents a method and corresponding software implementation for powertrain (PWT) mounting system layout design for decoupling rigid-body modes in the torque roll axis system. The novelty in the proposed method is that it requires a minimal set of inputs for determining mount topology, orientation and stiffness properties for decoupling powertrain modes, and as such it can be used at early design stages, unlike the conventional approaches based on analysis and optimization techniques. Consequently, PWT mounts can be positioned and oriented close to their optimal configuration, allowing to develop more realistic full vehicle models for conceptual (or early stage) designs and to run a more accurate dynamic analysis concerning secondary ride and vibrations. The proposed methodology is illustrated on a powertrain mounting system design example case.

A key issue in noise emission studies of noise producing machinery concerns the identification and analysis of the noise sources and their interaction and radiation into the far field. This paper presents a new acoustic measurement technique for noise source identification in stationary applications. The core of the technology is a handheld measurement instrument combining a position and orientation tracking device with a 3D sound intensity probe. The technique allows an on-line 3D visualization of the sound field while moving the probe freely around the test object. By focusing on the areas of interest, troublesome areas can be identified that require further in-depth analysis. The measurement technique is flexible, interactive and widely applicable in industrial applications. This paper explains the working principle and characteristics of this new technology and positions it to existing methods like traditional sound intensity testing and array techniques.

The paper presents first a description of the methods used for the analysis of global dynamics of rotating systems like jet engines but also auxiliary power units. Different methodologies are described so to model rotating parts using beam, but also Fourier multi-harmonic, three dimensional models or to take into account cyclic symmetry and multistage cyclic symmetry concepts. Advantages and disadvantages of the different model types are discussed and compared. The coupling of the rotating parts with casings and stators is then discussed both in the inertial frame and in the rotating frame. The effect on global dynamics of bearing and other linking devices is taken into account for different type of analysis from critical speed analysis, to harmonic and transient analysis. The effect of gears and gear boxes coupling different rotors (like it is the case for auxiliary power units in a jet engine) is then discussed and appropriate methods described so to model this coupling effect.