Search Results

In a two-stroke engine, carbon is a natural by-product of incomplete combustion. Fuel and oil quality vary leading to various degrees of carbon deposit build up on critical engine parts over time. If the carbon deposits are left on engine components and allowed to accumulate, it can lead to reduced horsepower, reduced fuel economy, increased emissions, and in the worst case the deposits can cause engine damage. A novel two-stroke engine oil was developed specifically to remove these deposits, restore the operating efficiency, and potentially lengthen the useful life of the two-stroke engine. In order to prove the restorative ability of this novel technology, dynamometer tests and field trials were conducted. In the dynamometer portion, the oil was tested in two of the standard TC-W3® certification tests for marine engine oils. The first was the OMC 40HP and the second was the OMC 70HP test.

A new field test procedure for evaluation of the sludge formation tendencies of lubricants has been developed. The procedure has the benefits of short running time, reduced variability, and dramatic separation of API SF vs API SG oils. This paper discusses development of the operational procedure and evaluation of four lubricants, including commercial-type API SF and API SG oils as well as experimental future oils. Significantly improved sludge ratings were obtained with an experimental API SG oil. The sludge formation process was studied using infrared spectroscopy, TAN, dielectric measurements, viscosity, quasielastic light scattering particle size, and transmission electron microscopy techniques. These analyses show production of contaminants which form insoluble particles that build up and precipitate out of suspension as sludge. Certain drain analyses can be used as tools for predicting field sludge deposition time.

As the motorcycle market grows, the fuel efficiency of motorcycle oils is becoming an important issue due to concerns over the conservation of natural resources and the protection of the environment. Fuel efficient engine oils have been developed for passenger cars by moving to lower viscosity grades and formulating the additive package to reduce friction. Motorcycle oils, however, which operate in much higher temperature regimes, must also lubricate the transmission and the clutch, and provide gear protection. This makes their requirements fundamentally very different from passenger car oils. Developing fuel efficient motorcycle oils, therefore, can be a difficult challenge. Formulating to reduce friction may cause clutch slippage and reducing the viscosity grade in motorcycles must be done carefully due to the need for gear protection.

The automotive vehicle market has seen an increase in the number of hybrid electric vehicles (HEVs), and forecasts predict additional growth. In HEVs, the hybrid drivetrain hardware can combine electric motor, clutches, gearbox, electro-hydraulics and the control unit. In HEV hardware the transmission fluid can be designed to be in contact with an integrated electric motor. One transmission type well-suited to such hybridization is the increasingly utilized dual clutch transmission (DCT), where a lubricating fluid is in contact with the complete motor assembly as well as the DCT driveline architecture. This includes its electrical components and therefore raises questions around the suitability of standard transmission fluids in such an application. This in turn drives the need for further understanding of fluid electrical properties in addition to the more usually studied engineering hardware electrical properties.

Conventional methods for determining automotive powertrain efficiency include (1) component-level testing, such as engine dynamometer, transmission stand or axle stand testing, (2) simulations based on component level test data and (3) vehicle-level testing, such as chassis dynamometer or on-road testing. This paper focuses on vehicle-level testing to show where energy is lost throughout a complete vehicle powertrain. This approach captures all physical effects of a vehicle driving in real-world conditions, including torque converter lockup strategies, transmission shifting, engine control strategies and inherent mechanical efficiency of the components. A modern rear-wheel drive light duty pickup truck was instrumented and tested on a chassis dynamometer. Power was measured at the engine crankshaft output, the rear driveshaft and at the dynamometer.

Increased awareness of preserving the environment has motivated the development of a wide variety of environmentally compatible products. Such products include environmentally compatible lubricants. Sale and use of these types of lubricants illustrates diligence by the lubricant manufacturer, original equipment manufacturer (OEM), and the consumer in contributing to a cleaner environment. The use of this type of lubricant could enhance the image of the lubricant manufacturer and vendor as well as the equipment manufacturer who employs such a fluid. To base such a lubricant on a vegetable oil creates a product environmentally friendly by its farming origin and its ability to readily biodegrade if released. No machinery is so uniquely suited to using vegetable oil based lubricants as agricultural equipment. Since this equipment is particularly close to the environment, the lubricant can easily come in contact with the soil, ground water, and crops.

Automatic transmission clutches are complex tribological systems. Frictional performance is controlled by the interaction of base fluids, additive components, composition clutches, and steel reaction plates with varying energy inputs and thermal stresses in an oxidizing environment. This paper, rather than addressing fully formulated fluid performance in such a system, takes a more fundamental approach where the number of system variables is reduced and the relative effects of formulation variables on system performance can be better examined. Relationships among observed friction performance, system oxidation, friction member condition, and representative performance additives are explored using a synthetic base fluid and a conventionally refined mineral base fluid.

The Cooperative Lubrication Research (CLR) Oil Test Engine, usually called the L-38, has been used for nearly 25 years to evaluate copper-lead journal bearing protection of gasoline rnotoroils under high-temperature, heavy-duty conditions. The test is sensitive to aggressive surface active additives that may encourage bearing corrosion. The L-38 also provides an estimate of oil durability, assessing the resistance of an oil to the accumulation of acidic by-products of combustion that could attack copper-lead bearings. However, the L-38 engine dynamometer test uses a heavily leaded gasoline that is no longer representative of the commercial fuels available in North America, Europe, or Japan. Rather than discard the L-38, this paper describes work to modify the L-38 procedure to run with unleaded gasoline.

Nylon is used as a material in the design of various components of automatic transmissions. Pump rotor guides and thrust washers are among components designed from nylon. Nylon must be compatible with automatic transmission fluid (ATF). An immersion test using nylon strips in various test fluids was developed. The nylon color change was independent of the physical properties (as measured by change of tensile force) of the material. Testing indicated that nylon color change is catalyzed by oxidation effects, and the change in tensile strength is related to thermal degradation. An automatic transmission fluid (ATF) containing calcium sulfonate detergent showed better oxidation resistance and caused less loss of tensile strength in nylon 6 (PA6).

THIS paper presents the results of a controlled field test of heavy-duty crankcase oils in a fleet of 15 Chevrolet cars. Operating conditions were selected to represent average or typical passenger-car service. After 15 months of operation (approximately 14,000 miles on each car) it was found that, in comparison with the results obtained with a nonadditive oil, a heavy-duty oil of MIL-0-2104 performance level reduced piston-ring wear by 37%, reduced cylinder-bore wear by 42%, and significantly improved engine cleanliness.

Diesel engine oils containing a balanced additive package composed of oxidation, corrosion, wear, rust and foam inhibitors plus ashless dispersants and metallic detergents provide long engine life. The major factor is metallic detergent component which contributes alkalinity to the oil and has a direct effect on engine cleanliness and durability. Increased detergent alkalinity reduces deposits and wear, resulting in improved oil control and longer engine life. Careful selection of detergent components is required to control cylinder-bore polishing in diesel engines to assure optimum antiwear and oil control performance.

The wet clutch system (WCS) is a complex combination of friction plates, separator plates and fluid (lubricant). The basic function of the WCS is to transfer torque under various operating conditions such as slipping, shifting, start/launch and/or torque converter clutch (TCC) operation. Under these conditions the slope of the coefficient of friction (μ or COF) versus slip speed (μ-v) curve must be positive to prevent shudder of the WCS, a highly undesirable condition in the lubricated friction system. An extended durability duty cycle test procedure is required to evaluate the WCS during which the μ-v curve is monitored for a negative slope, a condition indicating the potential for shudder. The friction plates, separator plates, and lubricant must be tested together and remain together during the test to be properly evaluated as a WCS.

The specific goal of this project was to determine if there is a difference in the lube oil degradation rates in a heavy-duty diesel engine equipped with an EGR system, as compared to the same configuration of the engine, but minus the EGR system. A secondary goal was to develop FTIR analysis of used lube oil as a sensitive technique for rapid evaluation of the degradation properties of lubricants. The test engine selected for this work was a Caterpillar 3176 engine. Two engine configurations were used, a standard 1994 design and a 1994 configuration with EGR designed to meet the 2004 emissions standards. The most significant changes in the lubricant occurred during the first 50-100 hours of operation. The results clearly demonstrated that the use of EGR has a significant impact on the degradation of the engine lubricant.

It has long been understood that the piston assembly of the internal combustion engine accounts for a significant proportion of total engine friction. Modern engines are required to have better fuel economy without sacrificing durability. The pursuit of better fuel economy drives trends like downsizing, turbocharging and direct injection fuelling systems that increase cylinder pressures and create a more arduous operating environment for the piston ring / cylinder bore tribocouple. The power-cylinder lubricant is therefore put under increased stress as modern engine technology continues to evolve. The conventional approach to investigating fundamental power-cylinder tribology employs bench-tests founded on assumptions which allow for simplification of experimental conditions.

An oil consumption test procedure has been developed in a 6-cyl, 425 hp, turbocharged and after-cooled diesel engine. Tests conducted on reference oils agree with good and poor oil consumption characteristics found with these same oils in the field. This paper includes evaluations using the engine test procedure as well as various laboratory bench tests which measure the effects of viscosity, volatility, and oxidation stability. Both bench and engine test results indicate that traditional properties, such as viscosity and volatility, do not completely account for variations in oil consumption. The data indicate that the problam of obtaining low diesel engine oil consumption may involve a complex combination of factors.

Deposit formation within turbocharger compressor housings can lead to compressor efficiency degradation. This loss of turbo efficiency may degrade fuel economy and increase CO2 and NOx emissions. To understand the role that engine oil composition and formulation play in deposit formation, five different lubricants were run in a fired engine test while monitoring turbocharger compressor efficiency over time. Base stock group, additive package, and viscosity modifier treat rate were varied in the lubricants tested. After each test was completed the turbocharger compressor cover and back plate deposits were characterized. A laboratory oil mist coking rig has also been constructed, which generated deposits having the same characteristics as those from the engine tests. By analyzing results from both lab and engine tests, correlations between deposit characteristics and their effect on compressor efficiency were observed.