Search Results

For Automatic transmission application, crankshaft torque is transferred to torque converter through flex plate. As the flex plate has no functional requirement of storing energy as in case of Manual Transmission (MT) flywheel, flex plate design can be optimized to great extent. Flex plate structure must have compliance to allow the axial deformation of torque convertor due to ballooning pressure generated inside the converter. Flex plate experiences dynamic torque and centrifugal forces due to high rotational speed. It should have compliance to accommodate the assembly misalignments with torque convertor in both axial and radial directions. In this paper, sequential and hybrid optimization techniques are described to optimize the flex plate design with stress, stiffness and mass as design constraints. The load path, corrugation length and axial stiffness of flex plate captured accurately using this hybrid optimization.

Precise control over mixture formation withhigh fuel pressure and multiple injections allows Gasoline Direct Injection (GDI) engines to be operated satisfactorily at extreme conditions wherePort Fuel Injection (PFI) engines wouldnormally struggle due to combustion instability issues. Catalyst heating phase is one such important condition which is initiated after a cold engine start to improve the effectiveness of the three-way catalyst (TWC). For a given TWC specification, fast light-offof TWC is achieved in the catalyst heating phase by increasing the exhaust gas temperature with higher exhaust mass flow. The duration of this phase must be as short as possible, as it is a trade-off between achieving sufficient TWC light off performance and fuel efficiency.

In the recent past a lot of emphasis is given for the overall weight reduction of the sound package used in the vehicles. The paper presents a study of one of such materials used in the automotive market. The dash panel is a primary area for the engine noise transmission to the cabin. Hence the material selection of the dash inner acoustic insulation is critical. In the conventional method a barrier (EVA) and a decoupler (foam) is used. In the conventional design the surface weight of the barrier has to be substantially high for the dash insulation to perform effectively and hence adds to more weight. In the present application of light weight material also known as dual density absorbers and barrier is used for the dash acoustic insulator. The study reveals the good acoustic performance of the light weight dash mat in terms of passenger cabin noise reduction and improved sound quality along with weight reduction.

Aerodynamic simulation using commercial CFD (Computational Fluid Dynamics) codes is now an integral part of the vehicle design process. Aerodynamic prediction and vehicle development program runs in parallel. This requires a good agreement between experimental measurements and CFD prediction of aerodynamic behavior of a vehicle. The comparison between experimental and simulation results show differences, as it may not be possible to replicate effect of all the wind tunnel parameters in the simulation. This paper presents the details of aerodynamic simulation process of a Crossover and its validation with the experimental results available from the wind tunnel tests. The results are compared for different configurations such as- closing the grille openings, removing the rearview mirror, adding ski-rack and using different tyres. This study also includes the effect of different wind speeds and yaw angles on the coefficient of drag.

Continually increasing customer demands and legislative Requirements regarding fuel economy, emissions, Performance, drive ability and comfort need to be met by every OEM's developing vehicles worldwide. There is a serious pressure to reduce CO2 emission from automotive application which contributes to around 15.9% of the total CO2 production based on the Surveys done time to time. In a developing market like India, many foreign players are entering with lots of option for offering to this market. The parameters of prime importance here are fuel efficiency with good drive ability and at the same time affordable price. Diesel engines are finding these benefits and attracting the buyer over its counterpart (Gasoline). The road condition and the driving pattern in India compared with developed countries differ to a major extent. In India, the Low speed uses are predominating in Cities and in Ghats.

Reducing the vibrations in the powertrain is one of the prime necessities in today's automobiles from NVH and strength perspectives. The necessity of 4×4 powertrain is increasing for better control on normal road and off-road vehicles. This leads to bulky powertrains. The vehicle speeds are increasing, that requires engines to run at higher speeds. Also to save on material costs and improve on fuel economy there is a need for optimizing the mass of the engine/vehicle. The reduced stiffness and higher speeds lead to increased noise and vibrations. One more challenge a powertrain design engineer has to face during design of its transmission housings is the bending / torsional mode vibrations of powertrain assembly. This aggravates other concerns such as shift lever vibrations, shift lever rattle, rise in in-cab noise, generation of boom noise at certain speeds, etc. Hence, reducing vibrations becomes an important and difficult aspect in design of an automobile.

The automotive industry is currently facing the challenge of significantly stringent requirements regarding CO₂ emission and fuel economy coming from both legislations and customer demand. Advanced engine technologies play a vital role for downsizing of gasoline engine. The development of key design technologies for high efficiency gasoline engines is required for the improvement of competitive power in the global automobile industry. This paper focused on effect of geometry of intake manifold of gas exchange process and consequently the performance of the engine. Specially, the optimal design technologies for the intake manifold and intake port shape must be established for high performance, increasingly stringent fuel economy and emission regulations. Space in vehicle or packaging constraints and cost are also important factors while consideration of the design.

This work discusses about the emission development of a 4 cylinder inline 3.3 liter CRDe to meet BS III emission norms applicable to 3.5 Ton and above category and upgradable to BS IV emission by suitable after treatment. This engine is developed from a 3.2l mechanical pump engine. During development the focus was on the usage of higher swept volume, selection of engine hardware like piston bowl, turbocharger, injectors and optimization of the injection parameters. A cost-effective solution for meeting the BS III norms in the LCV category without application of EGR and exhaust after treatment even though there is 15% increase of the power rating and 10% increase in Peak torque of the engine. Injection parameters like injection timing, injection quantity and pilot injection were optimized to meet the emission target.

In today's fast growing automobile world, the Emission limits are stringent; customer expectations of vehicle performance and Fuel economy are more. Achieving these parameters for the given engine are challenging task for any automobile engineers. BS4 Emission limits are 50% more stringent than BS3 limits and from April 2010 onwards, all passenger cars which will be selling in 13 metro cities in India should be BS4 emission compliant. In this paper, we have described how BS4 limits were achieved in a MPV with 2.49 l, 70kW Common Rail Direct Injection Turbocharged Diesel engine, with push rod. During Emission development, the following processes were followed to meet BS4 emission limits without sacrificing the engine performance, Fuel Economy and Noise. Selecting suitable hardwares like Turbocharger, EGR cooler at engine level to reduce NOx and Unburned Hydrocarbon Emissions with best Brake specific fuel consumption.

In current competitive environment automobile industry is under heavy pressure to reduce time to market. First time right design is an important aspect to achieve the time and cost targets. CAE is a tool which helps designer to come up with first time right design. This also calls for high degree of confidence in CAE simulation results which can only be achieved by undertaking correlation exercises. In automobiles most of the structures are subjected to vibration from dynamic loads. All the dynamic road loads are random in nature and can be very easily expressed in terms of power spectral density functions. In the current scenario structural durability of the parts subjected to vibration is done partially through modal performance and partially though frequency response analysis. The only question that arises is what amplitude to use at what frequency and how to map all the accelerated tests dynamic load frequency spectrum to simulation domain.

This article is focused on the development of hydrogen fuelled engine with detailed exposure on its derivation from base Compressed Natural Gas (CNG) engine to discuss the phenomenon on backfiring, control strategies (to avoid knocking and backfiring) and its performance, emission characteristics. In this work, timed manifold injection system was developed to have efficient control over the fuel supply. To achieve the best performance and emission out of the engine, governing parameter like injector pulse width and ignition timing were optimized at full load, part load and idling. For comparison of the results with the same engine experiments were also conducted with base fuel CNG and gasoline using the conventional fuel supply system. It was experimentally observed that engine when fuelled with Hydrogen (H2) produces less maximum power compared to CNG and gasoline.

In today's competitive automobile market, customers have become more sensitive towards NVH behavior of the vehicle than ever. The noise generated by gear rattle is one of the main contributors towards customer's overall NVH perception. This paper adopts a model based design approach towards gear rattle phenomenon to predict the tendency of gear rattle at a very early stage of design. This up-front understanding of gear rattle will potentially reduce the expensive design changes and iterations at later stages. A single unloaded gear pair is modeled in AMESim software, which is then extended to the complete gearbox in neutral condition. The sensitivity of rattle index for different input parameters is studied. Analysis on uncertainty propagation is carried out to find the rattle index distribution for Gaussian variation of input parameters. A novel rattle index based on Jerk is proposed and compared with the existing index.

Ground clearance plays an important role in Sports Utility Vehicles (SUV). Designers are good in designing their own systems but when it comes to integration of systems, the impact of one system on others and cascading effects become the major problems in full vehicle development. The test vehicle is a monocoque construction with power train in transverse (east-west) direction. Vehicle shudder is observed in lateral direction exciting the steering column, floor during the low gear power train run up in Wide Open Throttle (WOT) condition. The shudder is felt predominantly on the front half of the vehicle. Being a low frequency phenomenon with high energy it becomes critical and the phenomenon is easily perceivable by passenger. The paper discusses the measurement and analysis procedures to identify the root cause of shudder. Different modifications are tried out based on the analysis and an optimum solution is selected.

The customer perception about the door slam noise and its feel would indicate the brand image of the car. In this paper the authors have made an effort to improve the door slam noise quality of the vehicle, which is currently in production. This paper describes the probable areas in the door to improve the slam noise quality by attempting modifications in the door design factors, such as door alignments, door panel stiffness, door trims, window glass rattle, latch striker alignment, door seals, air extractor. Since the door closing event is a transient phenomenon, it requires special tools such as wavelet transforms, Zwicker loudness to understand the slam events precisely. Subjective jury evaluations have been conducted to understand the effect of these modifications and rank the modifications based on their contributions to the door slam quality.

BSR (Buzz, Squeak and Rattle) is one of the oldest concerns in automobiles which directly reflect the build, assembly and manufacturing quality of a vehicle. In a cabin all the areas where there is relative motion between two components, such as trims, instrument panel and seats, are prone to squeak. This paper explains the study of seat squeak measurement and diagnosis which is a major concern for one of the products which is already in the market. Since squeak is a friction induced non stationary phenomenon, lot of effort was required to generate squeak in both component as well as vehicle level. At component level, electrodynamic shaker was extensively used for generation of squeak signals. In Vehicle level, driving through different road patterns, pave track and forced excitation on four posters are performed for generation of squeak signals. In this paper usage of wavelet and Zwikker loudness are explained for the diagnosis of seat squeak to identify the problematic frequencies.

Whole Body Vibration (WBV) of tractors was measured on different surfaces in real world usage pattern of Indian customers on tractors of various capacities. Vibration levels were measured at the interface of the seat and the operator, on the seat base/floor and on the head. The mean weighted Root Mean Square (RMS) values along the different axes, the vector sum of weighted RMS values along the three orthogonal axes, the crest factor, Vibration Dose Value (VDV) and 8 h exposure levels were calculated according to ISO 2631-1. In addition to the above parameters, the transmissibility between the seat base and the seat interface (SEAT) and between the seat interface and the operator head (TR) were also calculated. Finally, these parameters were correlated with the subjective feel of customers which was captured through suitable questionnaires. It is observed that the Indian tractor operators are exposed to WBV that exceeds the cautionary boundaries set in place by the ISO 2631-1.

This paper establishes quick and accurate methods to experimentally determine the rigid body properties of a powertrain unit namely, the centre of gravity, the moment of inertia and the torque roll axis and also the rigid body dynamics of mounting system such as the rigid body modes, kinetic energy distribution, and elastic roll axis. The centre of gravity is determined using single point suspension and laser pointer to locate the axis passing through the centre of gravity. A special unifilar pendulum test rig is developed for determining the moment of inertia where an accelerometer measures the rotational oscillations for a given time period and the moment of inertia is determined by solving a set of inertial ellipsoid equations. An easy method of reorienting the powertrain is demonstrated in this paper.

One of the most essential components of automotive HVAC system is compressor. In a vehicle it is directly mounted on the engine. It derives power from the engine feed system to keep refrigerant moving in the HVAC system of the vehicle. It is also essential to complete the vapor compression cycle. During the operation, it causes considerable load on the engine and thus results in lower fuel efficiency and higher pollution. There are several types of compressors available globally. According to construction it can be classified as reciprocating piston type, scroll type and rotary vane type. The reciprocating piston types of compressors are further classified as fixed displacement and variable displacement. Normally the fixed displacement compressors have good idling cooling performance, but it increases the load on the engine. To reduce the load on the engine and to have good idling cooling performance, generally a variable displacement compressor is used.

The traditional approach of engine thermal behavior of engine during startup has largely been dependent on experimental studies and high fidelity simulations like CFD. However, these techniques require considerable effort, cost and time. The low fidelity simulations validated with experimental results are becoming more popular due to their ease in handling the several parameters such as cost effectiveness and quick predictive results. A four point mass model of engine thermal behavior during cold start has been developed to study the engine warm up temperature behavior. The four point mass model considers the lumped mass of coolant, mass of engine directly associated with the coolant, mass of engine oil and mass of engine directly associated with the engine oil. The advantage of four point model is to predict the coolant temperature as well as lubricant temperature during the transient warm up cycle of the engine.

For the thermal management of an automobile, the induced airflow becomes necessary to enable the sufficient heat transfer with ambient. In this way, the components work within the designed temperature limit. It is the engine-cooling fan that enables the induced airflow. There are two types of engine-cooling fan, one that is driven by engine itself and the other one is electrically driven. Due to ease in handling, reduced power consumption, improved emission condition, electrically operated fan is becoming increasingly popular compared to engine driven fan. The prime mover for electric engine cooling fan is DC motor. Malfunction of DC motor due to overheating will lead to engine over heat, Poor HVAC performance, overheating of other critical components in engine bay. Based upon the real world driving condition, 1D transient thermal model of engine cooling fan motor is developed. This transient model is able to predict the temperature of rotor and casing with and without holes.