Search Results

The objective of this work was to develop an experimental system to support development and validation of a model for the lubrication of two-piece Twin-Land-Oil-Control-Rings (hereafter mentioned as TLOCR). To do so, a floating liner engine was modified by opening the head and crankcase. Additionally, only TLOCR was installed together with a piston that has 100 micron cold clearance to minimize the contribution of the skirt to total friction. Friction traces, FMEP trend, and repeatability have been examined to guarantee the reliability of the experiment results. Then, engine speed, liner temperature, ring tension, and land widths were changed in a wide range to ensure all three lubrication regimes were covered in the experiments.

Currently, states that are out of compliance with the National Ambient Air Quality Standards must, according to the Clean Air Act Amendments of 1990 (CAAA), develop and implement control strategies that demonstrate specific degrees of reduction in emissions-with the degree of reduction depending upon the severity of the problem. One tool that has been developed to aid regulators in both deciding an appropriate course of action and to demonstrate the desired reductions in mobile emissions is EPA's Mobile 5a emission estimation model. In our study, Mobile 5a has been used to examine the effects of regulatory strategies, as applied to the Northeast United States, on vehicle emissions under worst-case ozone-forming conditions.

The MIT-based Mars Gravity Biosatellite payload engineering team has been engaged in designing and prototyping sensor and control systems for deployment within the rodent housing zone of the satellite, including novel video processing and atmospheric management tools. The video module will be a fully autonomous real-time analysis system that takes raw video footage of the specimen mice as input and distills those parameters which are of primary physiological importance from a scientific research perspective. Such signals include activity level, average velocity and rearing behavior, all of which will serve as indicators of animal health and vestibular function within the artificial gravity environment. Unlike raw video, these parameters require minimal storage space and can be readily transmitted to earth over a radio link of very low bandwidth.

Three fuels with cetane numbers of 45, 36 and 29 have been run at four load levels at each of three speeds in a Detroit: Diesel 3–71 engine with standard injectors. Measurements of temperatures, pressures, Load, fuel flow, cylinder pressure in one cylinder, strain gauge measurements from the rocker arm operating one injector and exhaust emissions were all recorded. Comparisons show little change in operation except for increases in ignition delay and rate of cylinder pressure rise with the low cetane fuels. It was concluded, on the basis of these short runs, that the intermediate fuel probably would not cause major difficulties but the lowest cetane fuel could possibly present problems with noise and engine durability.

Japan’s recent dominance of the international auto industry does not result from some major single factor, such as technological superiority or advanced automation. It derives from twenty years of building flexible, durable industrial systems integrating assemblers, suppliers, and related companies. Current competitive advantages result from combinations of seemingly unrelated company, government, and labor practices. Japan’s position of leadership will instigate major changes in international labor forces, corporate strategies, and government policies, as former auto powers adapt to new competition, and simultaneous shifts in energy and economics.

The present day measure of the ignition quality of a diesel fuel is the cetane number. Cetane number determination is carried out using a special single cylinder engine with reproducible operating conditions and variable compression ratio. The importance of the carbon skeletal structure of the fuel on the ignition quality is qualitatively well known, but the practice of defining the ignition quality of diesel fuels by a term, whose physical and/or chemical meaning is not well understood, has not been abandoned yet. The correlations that have been proposed recently, which relate the total fuel aromaticity or mid-boiling point, hydrogen content and density to the cetane number, suffer from the lack of representation of the fuel's compositional structure, and of well defined relationship, if any, between boiling point, hydrogen content, density and ignition quality.

Six experimental fuels representative of Canadian future fuel options were tested against a reference fuel in a Bombardier 12 cylinder, 4 stroke, 3000 hp, medium speed diesel. The reference fuel was a straight run ASTM #2-D. The first test fuel blend consisted of heavy atmospheric gas oil that extended the distillation range (higher end point) of the other blend component ASTM #2-D. The second fuel was a blend of a distillate cut from a mixture of conventional and tar sands crude with hydrogen treated cracked stock. This provided a fuel with substantial levels of aromatic and cracked components. The third fuel was gas oil side stream: a low cetane number, high aromatics level tar sands distillate. The fourth fuel was an equal portion blend of tar sands crude components, gas oil side-stream and heavy unifined gas oil. The fifth fuel was a blend of ASTM #2-D heating oil and a substantial portion of stabilized cracked stock.

A critical evaluation of the current ASTM method of rating diesel fuels, and of the available non-engine techniques for the estimation of cetane nunbers of diesel fuels is presented. The relationship between ignition quality and fuel composition is reviewed and it is shown that each member of an homologous series of hydrocarbons does not have the same ignition characteristics as the other members of the series. It is emphasized that the belief that paraffins have relatively high cetane ratings as compared to aromatics and cycloparaffins is not always correct. The basic flaw in the cetane index correlations, which use the easily measurable physical properties of the fuels as independent parameters, is explained. A fuel data base has been used to compare the different correlations.

Four experimental diesel fuels with cetane numbers (CN) of 40, 37, 35 and 27 have been tested in a Detroit Diesel Allison 3-71 engine using the standard N65 injectors. The 35 CN fuel was a blend of distillates from conventional and tar sands crude with hydrogen treated cat-cracked stock. This provided a fuel typical of the 1990's and beyond, with substantial levels of aromatic and cracked components. The 27 CN fuel was a blend of the same components as the 35 CN fuel only with a larger portion of the hydrogen treated cat-cracked component. The 40 CN fuel was identical to the 35 CN fuel with a .2% DII-3 Diesel Ignition Improver. The 37 CN fuel was a blend of Canadian winter diesel fuel oil and 24% Light Cycle Oil (LCO), The four experimental fuels and one reference fuel were tested at four load levels at each of three engine speeds. The performance and combustion characteristics were compared with the physical and chemical fuel properties.

Two Canadian tar sands derived experimental diesel fuels with cetane numbers of 26 and 36 and a reference fuel with a cetane number of 47 were tested in a Deutz (F1L511D), single cylinder, A stroke, naturally aspirated research engine. The fuels were tested at intake and cooling air temperatures of 30 and 0°C. The 36 cetane number fuel was tested with advanced, rated and retarded injection timings. Poor engine speed stability at light loads and excessive rates of combustion pressure rise were experienced with the lowest cetane number fuel. Detailed performance/combustion behavior is presented and a correlation with fuel structural composition is made. The analytical techniques used to characterize the fuels included liquid chromatography, gas chromatography mass spectrometry (GC-MS) and proton nuclear magnetic resonance spectrometry (PNMR).

One of the goals of designing engineering systems is to maximize the system's reliability. A reliable system must satisfy its functional requirements without failure throughout its intended lifecycle. The typical means to achieve a desirable level of reliability is through preventive maintenance of a system; however, this involves cost. A more fundamental approach to the problem is to maximize the system's reliability by preventing failures from occurring. A key question is to find mechanisms (and the means to implement them into a system) that will prevent its system range from going out of the design range. Functional periodicity is a means to achieve this goal. Three examples are discussed to illustrate the concept. In the new electrical connector design, it is the geometric functional periodicity provided by the woven wire structure. In the case of integrated manufacturing systems, it is the periodicity in scheduling of the robot motion.

Topology of liner finish is critical to the performance of internal combustion engines. Proper liner finish simulation processes lead to efficient engine design and research. Fourier methods have been well studied to numerically generate liner topology. However, three major issues wait to be addressed to make the generation processes feasible and reliable. First, in order to simulate real plateau honed liners, approaches should be developed to calculate accurate liner geometric parameters. These parameters are served as the input of the generation algorithm. Material ratio curve, the common geometry calculation method, should be modified so that accurate root mean square of plateau height distribution could be obtained. Second, the set of geometric parameters used in generating liner finish (ISO 13565-2) is different from the set of parameters used in manufacturing industry (ISO 13565-3). Quantitative relations between these two sets should be studied.