Search Results

Diesel particulate filters (DPFs) are a technology likely to be deployed to meet future stringent emission levels for heavy and light duty diesel powertrains in North America and Europe. This paper discusses experimental results in the active regeneration of DPFs. Attention is given to the system components, the information based on which regeneration is triggered, and the means to achieve a regeneration. The paper will report on successful regenerations under several extreme conditions.

Some communication buses are too powerful and expensive for simple digital on/off operations such as activating lights, wipers, windows, etc. For these applications the LIN bus is currently the most promising communication protocol across the world's automotive industry. This paper addresses a study using LIN (Local Interconnect Network) for Ford South America vehicles. This will propose a new electrical architecture designed with LIN network, which will be replacing the conventional rear and front lights cables in Trucks, where other higher protocols, such as CAN, are not cost effective. LIN is a new low cost serial communication system intended to be used for distributed electronic system that will allow gaining further quality enhancement and cost reduction on cables, connectors and switches.

Urea SCR is an established method to reduce NOx in dilute exhaust gas. The method is being used currently with stationary powerplants, and successful trials on motor vehicles have been conducted. The reason most often cited for rejecting urea SCR is lack of urea supply infrastructure, yet urea and other high nitrogen products are traded as commodities on the world market as a fertilizer grade, and an industrial grade is emerging. For a subset of commercial vehicles, urea can be provided by service personnel at designated terminals. But this approach does not support long distance carriers and personal use vehicles. The preferred delivery method is to add urea during vehicle refueling through a common fuel nozzle and fill pipe interface: urea / diesel co-fueling. Aqueous urea is well suited to delivery in this fashion.

It has been observed that a certain percentage of diesel particulate filters (DPFs) from the field form mid-channel ash plugs both in light duty and heavy duty applications. As revealed in a post mortem study, some field samples have ash plugs of 3-10 cm length in the middle of DPF inlet channels, which can potentially reduce the inlet channel volume by more than 50%. As a result, the mid-channel ash plug reduces the effective filtration area and decreases the effective channel open width in the middle of the channel. This explains why these filters are reported as having large increases in pressure drop. Moreover, the mid-channel ash deposits reduce the DPF service life and render the filter cleaning process ineffective. In the present study, an open source CFD tool is applied to study the 3D flow crossing two representative inlet and outlet DPF channels where the inlet channels have mid-channel ash plugs.

Commercial vehicles are being developed for long decades in Brazil creating a deep background on manufacturing process. With the current scenario a variety of different vehicles specifications (weight capacity, load distribution, torque, size, etc.) are being required by the market. Joints with bolts and nuts are the engineering solution for the most of the problems found in automotive engineering regarding commercial vehicles. Screw processes were made during the last 150 years. Nowadays current frame modifications on aftermarket are made with arc weld process that affects directly the material properties and the process needs to be performed by critical personal with training and capacity. In addition cost and timing does not fit for the best equation on how to proceed with the modifications. The solution proposed brings more flexibility on frame assemblies that can be extended to other products.

To meet stringent 2010 NOx emissions, many manufacturers are expected to deploy urea selective catalytic reduction systems. Indications from ARB are that a threshold monitor must be developed to monitor their performance. The most capable monitoring technology at this time relies on NOx sensors. This paper assesses the capability of the NOx sensor as an SCR monitoring device. To this end, the NOx sensor must be able to distinguish between a marginal and a threshold catalyst with enough separation to allow for variability. We present the noise factors associated with the NOx conversion of the SCR system, and analyze what NOx sensor accuracy we need to preserve separation in the face of those noise factors. It is shown that a 1.75 threshold monitor is not feasible with current NOx sensor technology. We analyze the benefit of a partial volume monitor, and show there is no advantage unless the slope error of the NOx sensor is drastically reduced from current levels.

Hydroformed truck frame side rails from circular tubes are studied for gage variations and pre-strain to be used in crash FEA modeling practice. This study provides simplified models that achieve feasible correlation with actual tests. Meanwhile, from plasticity theory we derive a forming equation in conjunction with forming limit diagrams to estimate material properties for hydroformed rails.

The growing competition of the automotive market makes more and more necessary the reduction of development time and consequently, the increase of the capacity to quickly respond to the launching of the competitors. One of the most costly phases on the vehicle development process is the field durability test, both in function of the number of prototypes employed and the time needed to its execution. More and more diffused, the fatigue life prediction methods have played an important part in the durability analysis via CAE. Nevertheless, in order they can be reliable and really being able to reduce the development time and cost, they need to be provided with load cases that can accurately represent the field durability tests. This work presents a CAE approach used for light trucks in order to get a reasonable understanding of component durability behavior due to payload increase. In general, road load data is not available for a new payload condition.

This paper discusses the possible impact of the FM tape recorder and servo-hydraulic actuators on the testing of automotive structures. The use of tape recorders and automatic data reduction systems will permit more accurate definition of service conditions and properly “set-the-stage” for laboratory testing. Servo-hydraulic strokers should encourage better laboratory simulation because of their great flexibility. Test set-up time is reduced, fixtures can be simplified and load control is more precise. Simultaneous multiple inputs can be controlled as to amplitude and phase relationships.

This paper analyzes the potential benefit of a model based DPF leakage monitor over a conventional DPF leakage monitor that checks pressure drop after a complete regeneration. We analyze the most important noise factors involved in both approaches and demonstrate that the model based leakage monitor does not improve on the conventional leakage monitor in accuracy. It does improve on completion frequency, but at the expense of a great modeling effort.

This study focused on occupant responses in very large pickup trucks in rollovers and was conducted in three phases. Phase 1 - Field data analysis: In a prior study [9], 1998 to 2020 FARS data were analyzed; Pickup truck drivers with fatality were 7.4 kg heavier and 4.6 cm taller than passenger car drivers. Most pickup truck drivers were males. Phase 1 extended the study by focusing on the drivers of very large pickup trucks. The size of 1999-2016 Ford F-250 and F-350 drivers involved in fatal crashes was analyzed by age and sex. More than 90% of drivers were males. The average male driver was 179.5 ± 7.5 cm tall and weighed 89.6 ± 18.4 kg. Phase 2 – Surrogate study: Twenty-nine male surrogates were selected to represent the average size of male drivers of F-250 and F-350s involved in fatal crashes. On average, the volunteers weighed 88.6 ± 5.2 kg and were 180.0 ± 3.2 cm tall with a 95.2 ± 2.2 cm seated height.