Search Results

Far-side occupants are not addressed in current government regulations around the world even though they account for up to 40% of occupant HARM in side impact crashes. Consequently, there are very few crash tests with far-side dummies available to researchers. Sled tests are frequently used to replicate the dynamic conditions of a full-scale crash test in a controlled setting. However, in far-side crashes the complexity of the occupant kinematics is increased by the longer duration of the motion and by the increased rotation of the vehicle. The successful duplication of occupant motion in these crashes confirms that a sled test is an effective, cost-efficient means of testing and developing far-side occupant restraints or injury countermeasures.

The increasing use of diesel and gasoline particulate filters requires advanced on-board diagnostics (OBD) to prevent and detect filter failures and malfunctions. Early detection of upstream (engine-out) malfunctions is paramount to preventing irreversible damage to downstream aftertreatment system components. Such early detection can mitigate the failure of the particulate filter resulting in the escape of emissions exceeding permissible limits and extend the component life. However, despite best efforts at early detection and filter failure prevention, the OBD system must also be able to detect filter failures when they occur. In this study, radio frequency (RF) sensors were used to directly monitor the particulate filter state of health for both gasoline particulate filter (GPF) and diesel particulate filter (DPF) applications.

The Gas Turbine Laboratory of the National Research Council of Canada (NRC) has been involved in icing certification testing of gas turbine engines for over 60 years. It has become evident from flight incident reports in recent years, that ice crystals can have serious effects on the performance of the core of a gas turbine. This has led to the proposal of a new certification requirement for turbofan engines. This paper describes the test facilities and procedures, as well as the analysis and verification methods, which have been used recently to develop a new ice crystal generating system. The paper describes the ice crystal production and delivery systems, as well as the design and development version for business jet sized engines. In addition, a description of some component testing using ice crystals on a heated flat plate is included to demonstrate that the facility can replicate rapid ice crystal build-up on surfaces which are significantly above the melting point.

The National Highway Traffic Safety Administration (NHTSA) routinely measures the force exerted on the barrier in crash tests. Thirty-six load cells on the face of the rigid barrier measure the force. This study examines the load cell barrier data collected during recent years of NCAP testing to determine how it can be used to assess vehicle compatibility in vehicle-to-vehicle front-to-side crashes. The height of the center-of-force measured by the columns of load cells is proposed as a metric for quantitatively describing the geometric properties of the crash forces. For front-to-side crashes, the geometric and stiffness properties of frontal structures during the early stages of crush are applicable. Consequently, geometric and stiffness measurements at a crush of 125 mm are presented in this paper. This paper shows the range of the compatibility and stiffness parameters measured on cars, pickups, vans, and multi-purpose vehicles.

Efficient aftertreatment management requires accurate sensing of both particulate filter soot and ash levels for optimized feedback control. Currently a combination of pressure drop measurements and predictive models are used to indirectly estimate the loading state of the filter. Accurate determination of filter soot loading levels is challenging under certain operating conditions, particularly following partial regeneration events and at low flow rate (idle) conditions. This work applied radio frequency (RF)-based sensors to provide a direct measure of the particulate filter soot levels in situ. Direct measurements of the filter loading state enable advanced feedback controls to optimize the combined engine and aftertreatment system for improved DPF management. This study instrumented several cordierite and aluminum titanate diesel particulate filters with RF sensors. The systems were tested on a range of light- and heavy-duty applications, which included on- and off-road engines.

This paper presents the results of a study of how people interacted with a production voice-command based interface while driving on public roadways. Tasks included phone contact calling, full address destination entry, and point-of-interest (POI) selection. Baseline driving and driving while engaging in multiple-levels of an auditory-vocal cognitive reference task and manual radio tuning were used as comparison points. Measures included self-reported workload, task performance, physiological arousal, glance behavior, and vehicle control for an analysis sample of 48 participants (gender balanced across ages 21-68). Task analysis and glance measures confirm earlier findings that voice-command interfaces do not always allow the driver to keep their hands on the wheel and eyes on the road, as some assume.

EQUIPMENT for measuring vibration in airplane structures and powerplants during actual flight is described in this paper. This development is the result of a cooperative research program carried out by the Bureau of Aeronautics of the U. S. Navy and the Massachusetts Institute of Technology with contributions of improvements in design and new features by the Sperry Gyroscope Co., Inc. In its essentials, the M.I.T.-Sperry Apparatus consists of a number of electrical pickup units which operate a central amplifying and recording unit. The recorder is a double-element photographic oscillograph. Each pickup is adapted especially to the type of vibration that it is intended to measure and is made so small that it does not appreciably affect the vibration characteristics of the member to which it is attached rigidly. By using a number of systematically placed pickups, all the necessary vibration information on an airplane can be recorded during a few short flights.

A human-centered systems analysis was applied to the adverse aircraft weather encounter problem in order to identify desirable functions of weather and icing information. The importance of contingency planning was identified as emerging from a system safety design methodology as well as from results of other aviation decision-making studies. The relationship between contingency planning support and information on regions clear of adverse weather was investigated in a scenario-based analysis. A rapid prototype example of the key elements in the depiction of icing conditions was developed in a case study, and the implications for the components of the icing information system were articulated.

Reliable means for on-board detection of particulate filter failures or malfunctions are needed to meet diagnostics (OBD) requirements. Detecting these failures, which result in tailpipe particulate matter (PM) emissions exceeding the OBD limit, over all operating conditions is challenging. Current approaches employ differential pressure sensors and downstream PM sensors, in combination with particulate filter and engine-out soot models. These conventional monitors typically operate over narrowly-defined time windows and do not provide a direct measure of the filter’s state of health. In contrast, radio frequency (RF) sensors, which transmit a wireless signal through the filter substrate provide a direct means for interrogating the condition of the filter itself.

The Cu-zeolite (CuZ) SCR catalyst enables higher NOx conversion efficiency in part because it can store a significant amount of NH3. “NH3 storage control”, where diesel exhaust fluid (DEF) is dosed in accord with a target NH3 loading, is widely used with CuZ catalysts to achieve very high efficiency. The NH3 loading actually achieved on the catalyst is currently estimated through a stoichiometric calculation. With future high-capacity CuZ catalyst designs, it is likely that the accuracy of this NH3 loading estimate will become limiting for NOx conversion efficiency. Therefore, a direct measurement of NH3 loading is needed; RF sensing enables this. Relative to RF sensing of soot in a DPF (which is in commercial production), RF sensing of NH3 adsorbed on CuZ is more challenging. Therefore, more attention must be paid to the “microwave resonance cavity” created within the SCR assembly. The objective of this study was to develop design guidelines to enable and enhance RF sensing.

Reducing cold-start emissions to meet increasingly stringent emissions limits requires fast activation of exhaust system sensors and aftertreatment control strategies. One factor delaying the activation time of current exhaust sensors, such as NOx and particulate matter (PM) sensors, is the need to protect these sensors from water present in the exhaust system. Exposure of the ceramic sensing element to water droplets can lead to thermal shock and failure of the sensor. In order to prevent such failures, various algorithms are employed to estimate the dew point of the exhaust gas and determine when the exhaust system is sufficiently dry to enable safe sensor operation. In contrast to these indirect, model-based approaches, this study utilized radio frequency (RF) sensors typically applied to monitor soot loading levels in diesel and gasoline particulate filters, to provide a direct measurement of stored water levels on the ceramic filter elements themselves.

MIT Lincoln Laboratory is tasked by the U.S. Federal Aviation Administration to investigate the use of the NEXRAD polarimetric radars* for the remote sensing of icing conditions hazardous to aircraft. A critical aspect of the investigation concerns validation that has relied upon commercial airline icing pilot reports and a dedicated campaign of in situ flights in winter storms. During the month of February in 2012 and 2013, the Convair-580 aircraft operated by the National Research Council of Canada was used for in situ validation of snowstorm characteristics under simultaneous observation by NEXRAD radars in Cleveland, Ohio and Buffalo, New York. The most anisotropic and easily distinguished winter targets to dual pol radar are ice crystals.

Many dynamic test systems currently exist to assess rollover. This paper introduces a new test device that combines features from a multitude of different tests. It also covers the concept development, a scaled prototype design and test results from both physical and virtual tests. The Guided Rollover Test (GRT) device subjects vehicles to repeatable initial conditions by having a cart follow a guided maneuver similar to a forward J-turn with an increasing curvature sufficient to roll most vehicles. A test vehicle is carried on the cart at constant longitudinal velocity until it rolls. The cart is fitted with a tripping edge to eliminate slipping and remove the influence of tire properties and road-surface friction. Vehicles are subjected to a rollover based on their own performance characteristics which define the dynamics and consequently the roof to ground contact.

The Global Aerospace Centre for Icing and Environmental Research Inc. (GLACIER) facility is located in Thompson, Manitoba, Canada. This facility provides icing certification tests for large gas turbine engines, as well as performance, endurance and other gas turbine engine qualification testing. This globally unique outdoor engine test and certification facility was officially opened back in 2010. The prime purpose of this facility is for icing certification of aero gas turbines. As a generic engine test facility, it includes the infrastructure and test systems necessary for the installation of both current and future gas turbine engines. The GLACIER facility completed its commissioning in the winter of 2010/2011, and has now experienced five years of full icing seasons. Rolls-Royce and Pratt and Whitney have both successfully performed certification and engineering icing testing with 5 engines completing their icing certification.

This paper describes the thermal management and design challenges of testing packaged integrated circuit (IC) devices, specifically device thermal conditioning and device-under-test (DUT) temperature control. The approach taken is to discuss the individual thermal design issues as defined by the device type (e.g. memory, microcontroller) and tester capabilities. The influence of performance-parameter specifications, such as the DUT parallelism, test time, index time, test-temperature range and test-temperature tolerance are examined. An understanding of these performance requirements and design constraints enables consideration of existing test handler thermal processing systems (e.g., gravity feed, pick and place), future test handler thermal concepts, and future high-parallelism testing needs for high-wattage memory and microprocessor devices. New thermal designs in several of these areas are described.

This study tracks vehicle design changes and frontal crash test performance in NHTSA's NCAP and IIHS consumer information tests since the mid-90s for the Honda Accord and Toyota Camry. The objective was to provide insights into how passenger cars have changed in response to frontal consumer information tests. The history of major design changes for each model was researched and documented. The occupant injury measures from both NHTSA and IIHS were computed and the ratings compiled for several generations of both vehicles. Changes in vehicle crash pulse and occupant injury measures from both NCAP and IIHS tests, and from Canadian low speed rigid barrier tests, when available, were used to assess driver frontal protection for various vehicle generations. Loading of the rigid barrier in NCAP tests was used to evaluate front end stiffness changes over the years.

A significant number of documented ankle injuries incurred in automobile accidents indicate some form of lateral loading is present to either cause or influence injury. A high percentage of these cases occur in the absence of occupant compartment intrusion. To date, no specific ankle injury mechanism has been identified to explain these types of injuries. To investigate this problem, several resources were used including full-scale crash test data, finite element models, and case study field data. Results from car-to-car, offset frontal crash tests indicate a significant lateral acceleration (10-18 g) occurs at the same time as the peak in longitudinal acceleration. The combined loading condition results in a significant lateral force being applied to the foot-ankle region while the leg region is under maximum compression.

In this study, the comparative stiffness of vehicle side and frontal structures is determined by available static test and crash test data. NHTSA has conducted a series of staged crash tests where a Honda Accord is impacted by different bullet vehicles at a closing velocity of 32.5 mph. These staged front-to-side crash tests are examined to assess the extent of damage to both the bullet and struck vehicle. The load cell barrier data for the bullet vehicles used in NHTSA's vehicle-to-vehicle front-to-side crash tests are examined to determine the geometric and stiffness properties of the frontal structures as measured in the NCAP tests. The geometric and stiffness measurements during the early stages of frontal crush are most influential in front-to-side crashes. The barrier data provides useful stiffness information. However, the number of rows of load cells may be insufficient to provide geometric information.