Search Results

Due to modern trends in the automotive industry, such as vehicle electrification, light-weighting, reduced NVH (Noise, Vibration and Harshness) packaging space, etc., it is desirable to have a low profile and light-weight acoustic material with multi-functionality. If one single layer of a thin acoustic material can provide comparable absorption and transmission loss to a multilayer treatment, it will benefit the industry by saving weight, packaging space and system cost. Acoustic absorption and sound transmission loss performance of a new dissipative material at reduced weight and thickness is introduced in this paper. The acoustic performance of the material was evaluated by using random incidence absorption and transmission loss as well as in-vehicle experiment. Further potential applications for this material have been identified using the Statistical Energy Analysis (SEA) method with panel leakage considered.

The damping effect that is observed when a fibrous acoustical treatment is applied to a thin metal panel typical of automotive structures has been modeled by using three independent techniques. In the first two methods the fibrous treatment was modeled by using the limp frame formulation proposed by Bolton et al., while the third method makes use of a general poro-elastic model based on the Biot theory. All three methods have been found to provide consistent predictions that are in excellent agreement with one another. An examination of the numerical results shows that the structural damping effect results primarily from the suppression of the nearfield acoustical motion within the fibrous treatment, that motion being closely coupled with the vibration of the base panel. The observed damping effect is similar in magnitude to that provided by constrained layer dampers having the same mass per unit area as the fibrous layer.

The combustion process after auto-ignition is investigated. Depending on the non-uniformity of the end gas, auto-ignition could initiate a flame, produce pressure waves that excite the engine structure (acoustic knock), or result in detonation (normal or developing). For the “acoustic knock” mode, a knock intensity (KI) is defined as the pressure oscillation amplitude. The KI values over different cycles under a fixed operating condition are observed to have a log-normal distribution. When the operating condition is changed (over different values of λ, EGR, and spark timing), the mean (μ) of log (KI/GIMEP) decreases linearly with the correlation-based ignition delay calculated using the knock-point end gas condition of the mean cycle. The standard deviation σ of log(KI/GIMEP) is approximately a constant, at 0.63. The values of μ and σ thus allow a statistical description of knock from the deterministic calculation of the ignition delay using the mean cycle properties

In recent years, interest in microperforated panels (MPPs) has been growing in the automotive industry and elsewhere. Acoustic performance prediction is an important step toward understanding and designing MPPs. This paper outlines a start-to-finish procedure to predict the transfer impedance of a particular MPP based on its hole geometry and to further use this information in a simple plane wave application. A computational fluid dynamics (CFD) approach was used to calculate the impedance of the MPP and the results compared to impedance tube and flow resistance measurements. The transfer impedance results were then used to create a computationally efficient acoustic finite element (FE) model. The results of the acoustic FE model were also compared to impedance tube measurements.

Cabin acoustic comfort is a major contributor to the potential sales success of new aircraft, cars, trucks, and trains. Recent design challenges have included the increased use of composites, and the switch to electrically powered vehicles, each of which change the interior noise spectral content and level. The role of acoustic absorption in cabins is key to the optimisation of cabin acoustic comfort for modern vehicles, with acoustic impedance data needed in order to assess and optimise the impact of each component of a given lay-up. Measurements of absorbing interior trim are traditionally performed using either sample holder tests in a static impedance tube (impedance and absorption), or through tests in reverberation rooms (absorption only). Both of these procedures present challenges. In-tube absorption and impedance measurements are destructive, requiring highly accurate sample cutting and sealing.

In recent work, it has been shown that conventional sound absorbing materials (e.g., lightweight fibrous media) can provide structural damping when placed adjacent to vibrating structures, including infinite panels, partially-constrained panels and periodically-supported panels typical of aircraft structures. Thus, a fibrous layer may serve two functions at once: absorption of airborne sound and the reduction of structure-borne vibration. It has also been found that the damping is primarily effective below the critical frequency of the structure, and that the damping results from viscous interaction between the fibrous layer and the evanescent near-field of the panel, in the region where incompressible flow caused by the panel vibration oscillates primarily parallel with the panel surface.

A multilayer acoustic treatment constructed of fibrous acoustic absorption material combined with dissipative acoustic material achieves a low profile and is lightweight and multi-functional, with properties that are desirable for NVH (noise, vibration, and harshness) treatments. The dissipative material consists of microfibers and acoustically active particles; this material was introduced in the last SAE NVH conference: A Novel Dissipative Acoustic Material [1]. In this paper, the acoustic performance of the multilayer treatment was evaluated by using random incidence absorption and transmission loss measurements, as well as in-vehicle experiments. Absorption and transmission loss were additionally modeled using the transmission matrix method (TMM). In the in-vehicle test, an OEM wheelhouse liner with Trim, for an SUV, was evaluated utilizing this new multilayer 3M treatment.