Search Results

This paper reports on the experimental study of carbide and polycrystalline diamond (PCD) drills used for drilling composite/titanium stacks. Materials systems used in this study were multi-directional carbon fiber in an epoxy matrix and titanium 6Al-4V. The drill materials included tungsten carbide (WC; 9%Co ultra fine grain) and polycrystalline diamond (PCD; bimodal grade). Torque and thrust force were measured during the drilling experiments. Tool wear of both drills was periodically examined during the drilling tests using various microscopic techniques such as optical and Scanning Electron Microscope (SEM). Effect of tool materials and process condition on hole quality parameters such as hole diameter, surface roughness, and titanium burrs, were examined. Dissimilar mechanical and thermal properties of the stacks affected the tool life and resulted in the decreased hole quality for both cutting tool materials, although to a differing degree.

This paper describes the application of the Design for Manufacture and Assembly (DFMA) method at Chrysler. Attention is focused on the development of the clutch and brake pedal and bracketry system of the PL project in the Small Car Platform. The Chrysler DFMA procedure including competitive evaluation and value engineering was utilized during the initial design phase involving product concept development from the original functional and manufacturing requirements. After the first laboratory tests, a number of key design and manufacturing concerns surfaced and led to a second cycle of DFMA analysis. The procedure permits major design functions and manufacturing and assembly process issues and criteria to be incorporated in the initial design stages.

The automobile industry has been using high-density polyethylene (HDPE) as a material to fabricate fuel tanks. Because untreated HDPE is permeable to the primary constituents of gasoline, these fuel tanks are now being produced with various barrier technologies that significantly reduce this permeation rate. Four currently available barrier technologies are fluorination, sulfonation, coextrusion, and the laminar barrier technology. These technologies have successfully proven to decrease the permeation rate of pure gasoline. However, it is suspected that their effectiveness may be reduced when alcohols are introduced into the fuel blend. In this work, we determine the permeation rates of gasoline-alcohol fuel blends through HDPE by conducting tests on 22-gallon HDPE fuel tanks and on small HDPE bottles fabricated with and without these barrier technologies. The goal of this study is to provide a comprehensive evaluation of these four barrier technologies.

A unique opportunity arose to make a direct comparison of aluminum, sheet molding compound (SMC) and steel using a common hood design. In considering all possible material combinations of inner and outer panels, it was discovered that some of the combinations were incompatible due to material properties. Only the compatible material combinations were considered. Three different joining techniques - welding, bonding and bonded hem flanging - were evaluated. The cost, weight and structural performance of the chosen hood material combinations were established. Areas of further development were identified, including design optimization for specific material combinations.

An OEM Natural Gas Vehicle (NGV) has been developed to address recently enacted Clean-Fuel Vehicle legislation. The NGV incorporates advanced fuel storage and fuel metering technologies to produce very low emissions and to provide superior customer value compared to aftermarket conversion units.

A selection of commercially available chromium and chromium-free post phosphate rinses along with a deionized water rinse were evaluated over several zinc and zinc-alloy coated sheet steels. The test specimens were pretreated and electrocoated on-line in an automotive assembly plant. The effect of the rinse treatments on the cosmetic corrosion performance of the substrates, after 5 years of exposure in an outdoor scab corrosion test was determined. After this exposure none of the rinse treatments had performed better than deionized water rinse on zinc and zinc-iron coated sheet. The zinc-nickel coating showed improved scribe creepage when treated with the Cr+6/Cr+3 rinse. Data is provided comparing the concentration of the treatments used vs scribe creepage and chipping corrosion paint loss.

A comprehensive selection of automotive sheet steels were exposed in an outdoor scab corrosion test to provide a base-line of cosmetic corrosion performance. Eighteen different coated sheet steels along with CRS as a control were processed using two commercially available zinc phosphate chemistries. The phosphating was done using both immersion and spray phosphate processes in a laboratory and an automotive assembly plant. Scribe creepage results are reported for 5 years outdoor scab exposure. Comparisons of the scribe creepage behavior of CRS, zinc, and zinc alloy coatings and the effect of the phosphate treatment are provided. An estimate of 10 years field performance is made.

The compression characteristics of thermoformable glass mat reinforcements with polyester binders have been studied as functions of temperature and platen closure rate. The mats were found to be more compliant and more compressible with increasing platen closure rate. At low closure rates, increasing the platen temperature has less of an effect on compressibility than at higher rates. Increasing the temperature also causes the mat to become more compliant. The compaction curves for the mats are described well with a logarithmic relation. This information is of interest to composite consolidation processes.

Typical sand-casting techniques have been shown to be inappropriate in pouring particulate reinforced aluminum metal matrix composite (Al-MMC) castings. New gating/risering configurations were necessary to produce castings of acceptable soundness. Several automotive components, including brake rotors, cylinder liners and camshaft thrust plates, were prepared using special techniques. Initial durability test results of several Al-MMC prototype components are presented.

The effect of compaction and fiber volume fraction on the transverse permeability of a fluid flowing through stacked layers of fiber mats has been experimentally studied. A Unifilo-101 random mat of continuous glass strands, held together with a binder soluble in styrene was used. The stacked layers were compacted using a Wabash instrumented press. Changing the maximum load, resulted in different fiber volume fractions. Mixtures of glycerol and water with viscosities between 85 and 100 mPa-s were used. This fluid is passed in a rectangular cell, through the fibers arranged transverse to the direction of flow. The pressure drop across the mat and the flow rate were monitored. The study was carried out at different flow rates of the fluid and was repeated for other fiber volume fractions. A power-law relation was observed between the permeability and the fiber volume fraction.

This paper presents a study of the effects of a resin soluble thermoplastic preform binder on the Resin Transfer Molding (RTM) process. The focus of the study is the rate of dissolution of the binder in the resin and the associated viscosity changes in the resin. Tests on the rate of binder dissolution from continuous strand glass mats show that after one minute of exposure to styrene, roughly half of the medium solubility binder from Unifilo 750 will dissolve and all of the high solubility binder from Unifilo 101 will dissolve. As the concentration of binder in the resin increases from 0 to 5 wt. percent, the viscosity of a vinyl ester resin increases from 125 cps to 280 cps. The viscosity of the resin has also been monitored in continuous flow experiments through the mats placed in a rectangular plague mold, at different flowrates. In these runs, the viscosity varied from 245 mPa-s to 145 mPa-s when the fill time was 2.2 minutes.

There are important changes unfolding in domestic industry. In the face of increased competition and the reality that traditional practices are no longer sufficient, manufacturers are taking daring new looks at the ways that they do business. Platforms and small business units are being formed within large companies to manage product lines. Cross-functional teams are replacing functional organizations as the driving forces in product development. Authority and leadership are being shifted lower and lower Into the working ranks, and the reengineering of work processes is becoming the challenge. This paper presents part of the story of Chrysler's Small Car Platform. It begins with an overview of the platform system. Then it focuses on the Process Phase of a vehicle program. The story is told to illustrate our experience in a continuous improvement process.

Resin transfer molding (RTM) is the process of choice for the Body Panels of the Viper Sports car. The objective of this paper is to outline the reasons for the choice of RTM, and discuss development of technology for Class A surfaces and the paint system. Accomplishments to date and finally the work yet to be completed will also be defined. Conclusions from the work to date indicate that the RTM process enables a reduction in vehicle development time through faster prototypes and tool build times and that high quality, Class A surfaces can be successfully achieved even with epoxy tools. Additional work is ongoing to reduce cycle times and finishing costs, and to improve the in-process dimensional stability.

To evaluate and refine interior architecture of the new Dodge Ram pickup truck three years before production, a road worthy interior package validation buck was built using a fiberglass body shell. Molds for the shell were made using CAD/CAM techniques. Advanced CAD/CAM techniques were used to build the interior buck of a subsequent model from individual panels molded in carbon fiber. This buck also included inner structural panels and interior trim components taken from CAD data. For this and subsequent new vehicle programs, refinement of construction techniques allows the bucks to serve as aids in product design and manufacturing feasibility studies.

Chrysler Corporation has developed an 8.0-liter engine for light truck applications. Numerous features combine to produce the highest power and torque ratings of any gasoline-fueled light truck engine currently available while also providing commensurate durability. These features include: a deep-skirt ten-cylinder 90° “V” block, a Helmholtz resonator intake manifold that enhances both low and mid-range torque, light die cast all-aluminum pistons for low vibration, a unique firing order for smooth operation, a “Y” block configuration for strength and durability, a heavy duty truck-type thermostat to control warm up, and a direct ignition system.

Chrysler Corporation's Jeep and Truck platform implemented a new design and prototype process for the body-in -white of a new pickup truck. A team approach achieved concurrent body design, stamping die design, assembly process development, and assembly tooling development. The first domestic US industry use of a 100% electronic design and release system was instrumental in the process. The new process produced a prototype body-in-white on time at 95 WBVP (weeks before volume production) with the highest level of production-intent components ever achieved within Chrysler at this stage of development.

Statistical Energy Analysis (SEA) is a useful tool for predicting the transmission of noise and vibration through the structures of automotive vehicles. This work discusses the identification of SEA internal loss factor parameters from experimental measurements of vehicle sound pressure levels and structural accelerations. A simple automotive vehicle SEA model can be constructed from elements idealized as uniform beams, flat plates and acoustic volumes. Such an SEA automotive vehicle model can accurately predict the vibro-acoustic response of an automotive vehicles when appropriate equivalent SEA parameters are identified from in situ experimental data. This paper will present an algorithm for identifying internal loss factors for SEA models. The paper will include an example of the application of the algorithm to identification of automotive vehicle internal loss factors from measured vehicle response data.

Most United States vehicle assembly plants produce significantly more automatic transmission equipped vehicles than manual transmission vehicles. Assembling these two vehicles on a common production line can create complexity problems. This paper describes the design and development of a pre-assembled manual transmission clutch and flywheel modular assembly which reduces most of these problems. This assembly is used on the 1993 model year mini-van with a 2.5L four cylinder engine. This modular clutch system utilizes the same starter ring gear carrier (driveplate) used on automatic transmission equipped vehicles. It pilots into the crankshaft similar to the automatic transmission torque converter. It is balanced as an assembly which results in a lower system imbalance. A significant system piece cost saving, in comparison with today's competitive market, was achieved.

Chrysler Corporation Interior Electrical\Entertainment Department currently has three different mounting tab configurations on the radio escutcheon required by five platforms for radio installation. Prior to the re-organization into platforms, the corporation had one corporate mounting configuration. The reorganization into platforms encouraged diversification including different radio mounting locations. This however, requires three separate part numbers for the same radio unit, resulting in additional cost. How can we assure product diversification between platforms while controlling cost and managing complexity?

Although numerical simulation techniques for sheet metal forming become increasingly maturing in recent years, prediction of springback remains a topic of current investigation. The main point of this paper is to illustrate the effectiveness of a modelling approach where static implicit schemes are used for the prediction of springback regardless whether a static implicit or dynamic explicit scheme is used in the forming simulation. The approach is demonstrated by revisiting the 2-D draw bending of NUMISHEET'93 and numerical results on two real world stampings.