Search Results

Austempered ductile iron (ADI) is a material having excellent mechanical properties and damping capacity. However practical mass production of ADI gears has not been possible due to ADI's poor machinability and distortion during the austempering heat treatment. With a new process method of carrying out hobbing before austempering when the material is in its soft condition, then austempering it and lastly, conducting the shave finishing process, we have diminished the above defects and developed practical ADI gears. These new gears generate less noise than ordinary nitrocarburized steel gears and are superior in pitting resistance.

Several different steel sheets were tested for energy absorption, using hat square columns and dynamic crash testing. Results indicate that steel sheets containing large volume fraction of retained austenite have relatively high energy absorption. The relationship between retained austenite and energy absorption was analyzed. These special steel sheets have already been successfully used for production body parts, such a front-side-member, without difficulties arising in volume production.

This paper describes a calculating method to predict the quasi-static collapsing behaviors of spot-welded closed-hat section curved beams under axial compression. The overall deformat ions and the local buckling modes of beams were calculated using a geometrical model. Force-displacement relations were predicted by a elastic-plastic structural analysis method using the ‘plastic hinge’ concept. Collapsing tests were made on beams which are differenting section size, rotation angle, and metal sheet thickness. Comparisons between the calculated and experimental results of deformed shapes of beams, the local buckling modes and the force displacement relations are discussed.

Vulcanized rubber hoses are difficult to recycle and have a complicated manufacturing process. Recently, we have developed the vacuum hose for engine control out of thermoplastic elastomers. As a result of this development, scrap material from the manufacturing process can be recycled and, in addition, about a 30 percent weight reduction and a 20 percent cost reduction are achievable by virtue of the lower specific gravity and by the more simplified manufacturing process. In order to assess the feasibility of using thermoplastic elastomers for vacuum hoses, we developed a heat aging simulation test method. This was achieved by first investigating the actual vehicle environmental conditions of currently used vacuum hoses by retrieving and examining these hoses from used vehicles. We then extrapolated what the condition of such hoses would be after being subjected to heat aging for 200,000 km of service in an actual vehicle, and applied this calculation to our newly developed hoses.

A new prototype oxygen storage componented oxygen sensor has been developed which shows significant emission reductions of a 3-way catalyst system. This sensor is composed of ceria, as an oxygen storage component and supported pellets as a buffer layer surrounding the protective coating of the sensor element. This sensor offers a more rapid response than conventional ones under lean and rich fuel mixture excursions, which is caused by CO or O2 electrode poisoning.

The sodium β″-Al2O3 is one of the prime candidate as the solid state electrolyte in using the Alkali Metal Thermo-Electric Converter (AMTEC). This paper reports the properties of β″-Al2O3/ZrO2 composite electrolyte in order to improve the durability of the cell and its performance for the power generation as the AMTEC. It is shown that the addition of ZrO2 to the β″-Al2O3 is able to control the microstructure, and the fabrication procedure of the electrolyte with the ZrO2 addition is selected. This paper also reports the new concepts of the AMTEC cells that are connected in series in order to raise generation voltage and shows that the adaptability of the AMTEC for terrestrial power generation is improved by these concept.

Mitsubishi Motors Corporation uses spiral bevel gears in the transfer system for 4-wheel drive passenger cars modified from the front wheel drive configuration. This transfer gear ratio is near 1:1, and gears have uniform depth teeth cutting by the continuous generating method of OERLIKON cutting machine. In this method, the cutter and the work rotations are timed together to accomplish continuous indexing and cutting in order to enable high productivity. In general, it is difficult to reduce the meshing noise of spiral bevel gears and control its quality. The authors established the tooth surface coordinates, to reduce the meshing noise, by studying the influence of tooth surface coordinates on the meshing transmission error (MTE).

We have developed a tappet with a cam lobe contacting tip made of a hard sintered material whose base material is cobalt, which adheres less to the steel of camshafts, and which also contains fine particles of tungsten carbide and chrome carbide. We have established a new evaluation method to access wear resistance performance of the tappet. It enables us to measure directly the friction force generated between the cam lobe and tappet and to evaluate anti-scuffing performance with high accuracy because we can clarify the time, load and cam angle at which scuffing occures.

Wet multiple plate clutches consist of friction plates, on which a friction material is bonded, and mating plates that are plain metal plates. Since the frequency and the range of load in the field of forklift trucks vary widely and are more severe than those for passenger cars, the wet multiple plate clutches on forklift trucks are often damaged. Damaged clutches that were returned from the field typically had 3 types of symptoms: 1.Only the friction material was damaged, 2.Only the mating plates were deformed, 3.Both symptoms were observed. It was clear that the cause of these symptoms depended on the difference of the operating application and the strength criteria of each part. This showed that a design guide for wet multiple plate clutches considering the strength balance between the two parts according to the work application was required. The relevant flow chart of this design process was proposed.

One of the important feature in the Environment Control and Life Support System required to support long duration mission at the Space Station is an oxygen supply for the human metabolism. The recovery of oxygen from the concentrated carbon dioxide through chemical methods will give significant advantage to the Space Station by reducing the supply requirement of the consumables, such as oxygen bottles. Oxygen recovery plants using the Bosch reaction and the Sabatier reaction are experimentally developed and tested. The Bosch reaction has been considered to produce carbon and water directly from carbon dioxide by the hydrogenization process. But it seems to proceed through two steps with carbon monoxide as the intermediate product. Also the total production rate is relatively low and the carbon deposited is less solid. The Sabatier reaction requires two steps to achieve carbon and water, with methane as the intermediate product.

Experimental study on a turbine housing with inner insulation structure has been conducted for rapid light-off of the catalyst unit, which is located at the downstream side of turbochargers. The turbine housing with feasible inner-insulation structures has been designed and prototyped. It is referred to as the inner-insulated turbine housing. The concept of inner-insulation structures is a combination of sheet metals and insulators. The turbine housing was built using metal additive manufacturing with powder bed fusion technique. The gas stand test demonstrates the inner-insulated turbine housing under cold start-up with high temperature and idle condition to evaluate the time reduction for activation of the catalyst unit. To acquire the thermal and flow characteristic of the catalyst element, sheathed thermocouples were installed in the catalyst element.

Improvement of an air revitalization technology of ECLSS (Environment Control and Life Support System) is one of the key elements in development and operation of future human space systems. The paper summarizes a trace-contaminant control system which employs “thermal storage / combustion” method for reduction of cabin and equipment-generated off-gases. For comparison, the International Space Station will be equipped with a trace-contaminant system utilizing “oxidization” method with catalyst substances. Preliminary functions of the processor were also evaluated to determine the designing parameters for a space system hardware. The results indicate the capability of processor under large volumes and high concentration of trace gases, and its systematic feasibility.

In recent year, higher strength for truck and bus transmission gear has become necessary. For the transmission gears, carburized gears have generally been used. We have examined the effects of shot peening and grinding using a CBN grindstone on the pitting strength and the bending fatigue strength of a carburized gear, and further evaluated a material which reduces the structual anomalies produced during carburization. As a result, it has been found that shot peening or CBN grinding is more effective for improving both pitting strength and bending fatigue strength than improving the material composition. Therefore, it is evident that residual compressive stress caused by shot peening or CBN grinding suppresses the propagation of cracks.

This paper describes the results of the study and research on ovate wire helical springs which have been jointly conducted by the members of the Japan Society for Spring Research consisting of the engineers from material suppliers, wire and spring producers and automotive manufacturers as well as researchers at Japanese universities. Attention is focused particularly on two types of wire cross sections, typical elliptical shape and Fuchs' egg-shape. Stresses on these two cross sections were analyzed by numerical calculations within the range of practical specification, and then the results have been compared with those of round wire spring. As a result, it has been found that the elliptical wire spring is superior to Fuchs- egg-shaped one for general application. Simple designing methods for the both types of wire helical springs have been developed based on the findings from the stress analysis.