Search Results

The blade crossing event of a coaxial counter-rotating rotor is a potential source of noise and impulsive blade loads. Blade crossings occur many times during each rotor revolution. In previous research by the authors, this phenomenon was analyzed by simulating two airfoils passing each other at specified speeds and vertical separation distances, using the compressible Navier-Stokes solver OVERFLOW. The simulations explored mutual aerodynamic interactions associated with thickness, circulation, and compressibility effects. Results revealed the complex nature of the aerodynamic impulses generated by upper/lower airfoil interactions. In this paper, the coaxial rotor system is simulated using two trains of airfoils, vertically offset, and traveling in opposite directions. The simulation represents multiple blade crossings in a rotor revolution by specifying horizontal distances between each airfoil in the train based on the circumferential distance between blade tips.

In February 2004 NASA released “The Vision for Space Exploration.” The important goals outlined in this document include extending human presence in the solar system culminating in the exploration of Mars. Unprocessed waste poses a biological hazard to crew health and morale. The waste processing methods currently under consideration include incineration, microbial oxidation, pyrolysis and compaction. Although each has advantages, no single method has yet been developed that is safe, recovers valuable resources including oxygen and water, and has low energy and space requirements. Thus, the objective of this project is to develop a low temperature oxidation process to convert waste cleanly and rapidly to carbon dioxide and water. In the Phase I project, TDA Research, Inc. demonstrated the potential of a low temperature oxidation process using ozone. In the current Phase II project, TDA and NASA Ames Research Center are developing a pilot scale low temperature ozone oxidation system.

Some selected segments of the ascent and the on-orbit data from the Space Shuttle flight, STS114, as well as some selected laboratory test article data have been analyzed using wavelets, power spectrum and autocorrelation function. Additionally, a simple approximate noise test was performed on these data segments to confirm the presence or absence of white noise behavior in the data. This study was initially directed at characterizing the on-orbit background against which a signature due to an impact during on-orbit operation could be identified. The laboratory data analyzed here mimic low velocity impact that the Orbiter may be subjected to during the very initial stages of ascent.

An innovative design that meets both Shuttle and Space Station requirements for a user-friendly, volume-efficient, portable glovebox system has been developed at Ames Research Center (ARC). The Standard Interface Glovebox (SIGB) has been designed as a two Middeck locker-sized system that mounts in a Middeck Rack Structure (MRS) or in any rack using the Standard Interface Rack (SIR) rail spacing. The MRS provides structural support for the SIGB during all aspects of the mission and is an interface consistent with NASA's desire for commonality of mechanical interfaces, allowing the SIGB to be flown on essentially any manned space platform. The SIGB provides an enclosed work volume which operates at negative pressure relative to ambient, as well as excellent lighting and ample work volume for anticipated life sciences-related experiment operations inflight.

Pressure-sensitive paint (PSP) technology is a technique used to experimentally determine surface pressures on models during wind tunnel tests. The key to this technique is a specially formulated pressure-sensitive paint that responds to, and can be correlated with the local air pressure. Wind tunnel models coated with pressure-sensitive paint are able to yield quantitative pressure data on an entire model surface in the form of light intensity values in recorded images. Quantitative results in terms of pressure coefficients (Cp) are obtained by correlating PSP data with conventional pressure tap data. Only a small number of surface taps are needed to be able to obtain quantitative pressure data with the PSP method. This technique is gaining acceptance so that future automotive wind tunnel tests can be done at reduced cost by eliminating most of the expensive pressure taps from wind tunnel models.

Samples of Mars surface material will return to Earth in 2014. Prior to curation and distribution to the scientific community the returned samples will be isolated in a special facility until their biological safety has been assessed following protocols established by NASA’s Planetary Protection Office. The primary requirements for the pre-release handling of the Martian samples include protecting the samples from the Earth and protecting the Earth from the sample. A testbed will be established to support the design of such a facility and to test the planetary protection protocols. One design option that is being compared to the conventional Biological Safety Level 4 facility is a double walled differential pressure chamber with airlocks and automated equipment for analyzing samples and transferring them from one instrument to another.

CO2 removal, recovery and reduction are essential processes for a closed loop air revitalization system in a crewed spacecraft. Typically, a compressor is required to recover the low pressure CO2 that is being removed from the spacecraft in a swing bed adsorption system. This paper describes integrated tests of a Temperature-Swing Adsorption Compressor (TSAC) with high-fidelity systems for carbon dioxide removal and reduction assemblies (CDRA and Sabatier reactor). It also provides details of the TSAC operation at various CO2 loadings. The TSAC is a solid-state compressor that has the capability to remove CO2 from a low-pressure source, and subsequently store, compress, and deliver it at a higher pressure. TSAC utilizes the principle of temperature-swing adsorption compression and has no rapidly moving parts.

A series of tests has been completed in which suckdown and fountain forces and pressures were measured on circular plates and twin-tandem-jet generic STOVL (short takeoff and vertical landing) configurations. The tests were conducted using a small-scale hover rig, for jet pressure ratios up to 6 and jet temperatures up to 700°F. The measured suckdown force on a circular plate with a central jet was greater than that found with a commonly used empirical prediction method. The present data showed better agreement with other sets of data. The tests of the generic STOVL configurations were conducted to provide force and pressure data with a parametric variation of parameters so that an empirical prediction method could be developed. The effects of jet pressure ratio and temperature were found to be small. Lift improvement devices were shown to substantially reduce the net suckdown forces. Paper to be presented at SAE Aerospace Meeting, Dayton, Ohio, April 24-27, 1990

Pyrolysis processing of solid waste in space will inevitably lead to carbon formation as a primary pyrolysis product. The amount of carbon depends on the composition of the starting materials and the pyrolysis conditions (temperature, heating rate, residence time, pressure). Many paper and plastic materials produce almost no carbon residue upon pyrolysis, while most plant biomass materials or human wastes will yield up to 20-40 weight percent on a dry, as-received basis. In cases where carbon production is significant, it can be stored for later use to produce CO2 for plant growth. Alternatively it can be partly gasified by an oxidizing gas (e.g., CO2, H2O, O2) in order to produce activated carbon. Activated carbons have a unique capability of strongly absorbing a great variety of species, ranging from SO2 and NOx, trace organics, mercury, and other heavy metals.

The wing of the Learjet Model 60 was tailored for improved aerodynamic characteristics using the TRANAIR transonic full-potential CFD code. A root leading edge glove and wing tip fairing were shaped to reduce shock strength, improve cruise drag and extend the buffet limit. The aerodynamic design was validated by wind tunnel test and flight test data.

A new oil-fringe imaging skin friction (FISF) technique to measure skin friction on wind tunnel models is presented. In the method used to demonstrate the technique, lines of oil are applied on surfaces that connect the intended sets of measurement points, and then a wind tunnel is run so that the oil thins and forms interference fringes that are spaced proportional to local skin friction. After a run the fringe spacings are imaged with a CCD-array digital camera and measured on a computer. Skin friction and transition measurements on a two-dimensional wing are presented and compared with computational predictions.

A method of estimating the load-bearing fuselage weight and wing weight of transport aircraft based on fundamental structural principles has been developed. This method of weight estimation represents a compromise between the rapid assessment of component weight using empirical methods based on actual weights of existing aircraft, and detailed, but time-consuming, analysis using the finite element method. The method was applied to eight existing subsonic transports for validation and correlation. Integration of the resulting computer program, PDCYL, has been made into the weights-calculating module of the AirCraft SYNThesis (ACSYNT) computer program. ACSYNT has traditionally used only empirical weight estimation methods; PDCYL adds to ACSYNT a rapid, accurate means of assessing the fuselage and wing weights of unconventional aircraft.

A three country effort (U.S., Russia, and Bulgaria) has upgraded the plant growth facilities on the Mir Space Station and used the new facility to grow wheat for 90 days. The Svet plant-growth facility was reactivated and used in an initial experiment as part of the Shuttle/Mir program, August to November, 1995. The Svet system, used first to grow cabbage and radish during a 1990 experiment, was augmented by the addition of a U.S. developed Gas Exchange Measurement System (GEMS) that measures a range of environmental parameters plus transpiration, photosynthesis, and possibly respiration. Environmental parameters include cabin, chamber, root-zones, and leaf temperatures. Light levels, relative humidity, oxygen, and atmospheric pressure are also measured. High-accuracy water-vapor and carbon-dioxide concentrations and differences are measured using specially developed IRGA systems.

During 1995, we tested instruments and attempted a seed-to-seed experiment with Super-Dwarf wheat in the Russian Space Station Mir. Utah instrumentation included four IR gas analyzers (CO2 and H2O vapor, calculate photosynthesis, respiration, and transpiration) and sensors for air and leaf (IR) temperatures, O2, pressure, and substrate moisture (16 probes). Shortly after planting on August 14, three of six fluorescent lamp sets failed; another failed later. Plastic bags, necessary to measure gas exchange, were removed. Hence, gases were measured only in the cabin atmosphere. Other failures led to manual watering, control of lights, and data transmission. The 57 plants were sampled five times plus final harvest at 90 d. Samples and some equipment (including hard drives) were returned to earth on STS-74 (Nov. 20). Plants were disoriented and completely vegetative. Maintaining substrate moisture was challenging, but the moisture probes functioned well.

Hover and ground-effect tests were conducted with the Lockheed-Martin Large Scale Powered Model (LSPM) during June-November 1995 at the Outdoor Aerodynamics Research Facility (OARF) located at NASA Ames Research Center. This was done in support of the Joint Strike Fighter (JSF) Program being lead by the Department of Defense. The program was previously referred to as the Joint Advanced Strike Technology (JAST) Program. The tests at the OARF included: engine thrust calibrations out of ground effect, measurements of individual nozzle jet pressure decay characteristics, and jet-induced hover force and moment measurements in and out of ground effect. The engine calibrations provide data correlating propulsion system throttle and nozzle settings with thrust forces and moments for the bare fuselage with the wings, canards, and tails removed. This permits measurement of propulsive forces and moments while minimizing any of the effects due to the presence of the large horizontal surfaces.

The 1/8-scale Generic Conventional Model was studied experimentally in two wind tunnels at NASA Ames Research Center. The investigation was conducted at a Mach number of 0.15 over a Reynolds number range from 1 to 6 million. The experimental measurements included total and component forces and moments, surface pressures, and 3-D particle image velocimetry. Two configurations (trailer base flaps and skirts) were compared to a baseline representative of a modern tractor aero package. Details of each configuration provide insight into the complex flow field and the resulting drag reduction was found to be sensitive to Reynolds number.

Propulsion system sizing for mechanical flap and externally blown flap aircraft is demonstrated. Included in this study is the effect of various levels of noise suppression on the aircraft final design characteristics. Both aircraft are sized to operate from a 3000 ft runway and perform the same mission. For each aircraft concept, propulsion system sizing is demonstrated for two different engine cycles-one having a fan pressure ratio of 1.5 and a bypass ratio of 9 and the other having a fan pressure ratio of 1.25 and a bypass ratio of 17.8. The results presented include the required thrust to weight ratio, wing loading, resulting gross weight and direct operating costs as functions of the engine noise level for each combination of engine cycle and aircraft concept.

Accurate root zone moisture control in microgravity plant growth systems is problematic. With gravity, excess water drains along a vertical gradient, and water recovery is easily accomplished. In microgravity, the distribution of water is less predictable and can easily lead to flooding, as well as anoxia. Microgravity water delivery systems range from solidified agar, water-saturated foams, soils and hydroponics soil surrogates including matrix-free porous tube delivery systems. Surface tension and wetting along the root substrate provides the means for adequate and uniform water distribution. Reliable active soil moisture sensors for an automated microgravity water delivery system currently do not exist. Surrogate parameters such as water delivery pressure have been less successful.

The desire to provide integrated surface pressures for aerodynamic loads measurements has been a driving force behind the development of pressure-sensitive paint (PSP). To demonstrate the suitability of PSP for this purpose, it is not sufficient to simply show that PSP is accurate as compared to pressure taps. PSP errors due to misregistration or temperature sensitivity may be high near model edges, where pressure taps are rarely installed. Thus, PSP results will appear good compared to the taps, but will yield inaccurate results when integrated. A more stringent technique is to compare integrated PSP data over the entire model surface with balance and/or CFD results. This paper describes a simple integration method for PSP data and presents comparisons of balance and PSP results for three experiments. PSP is shown quite accurate for normal force measurements, but less effective at determining axial force and moments.

An overset grid approach is used to analyze a 3-element trapezoidal wing high-lift configuration. A new software system was developed to automate the overset computational fluid dynamics process. A three-dimensional grid resolution study is conducted, and comparisons of numerical results are made to experimental data which were obtained after the simulations. Comparisons between numerical and experimental data are in good agreement for the lift coefficient over a wide range of angles of attack, up to and including CLmax. Comparisons of chordwise distributions of the pressure coefficient between numerical and experimental data are in good agreement for all three elements, except the lift is under-predicted for the tip region when the wing is near CLmax.