Search Results

A review of the research accomplished in 2009 in the System-Level Design, Analysis and Simulation Tools (SLDAST) of the NASA's Airspace Systems Program is presented. This research thrust focuses on the integrated system-level assessment of component level innovations, concepts and technologies of the Next Generation Air Traffic System (NextGen) under research in the ASP program to enable the development of revolutionary improvements and modernization of the National Airspace System. The review includes the accomplishments on baseline research and the advancements on design studies and system-level assessment, including the cluster analysis as an annualization standard of the air traffic in the U.S. National Airspace, and the ACES-Air MIDAS integration for human-in-the-loop analyzes within the NAS air traffic simulation.

Conventional hydraulic steering systems keep improving performance and driving comfort by introducing advanced features via mechanical design. The ever increasing mechanical complexity requires the advanced modeling and simulation technology to mitigate the risks in the early stage of the development process. In this paper, we focus on advanced modeling tools environment with an example of a load sensing hydraulic steering system. The complete system architecture is presented. Analytical equations are developed for a priority valve and a steering control unit as the foundation of modeling. The full version of hydraulic steering system model is developed in Dymola platform. In order to capture interaction between steering and vehicle, the co-simulation platform between the hydraulic steering system and vehicle dynamics is established by integrating Dymola, Carsim and Simulink.

This paper presents a method for indirect measurement of tire slip angles from chassis acceleration, yaw rate, and steer angle measurements. The chassis is assumed to be rigid so that acceleration data can be integrated to estimate velocities of the front and rear of the vehicle, from which slip angles can be predicted. The difference in front and rear slip angles is indicative of vehicle oversteer/understeer. Understeer data can then be correlated with position on the track to better understand vehicle handling behavior, aiding the tuning process. The technique is presented, and shown to work well with simulated data, even when the data is corrupted with up to 20% noise. Therefore, the inversion process presented here is theoretically sound. However, when the technique is applied to measured data from race cars, it is shown to be inaccurate. One suspected problem is the difficulty of getting accurate yaw rate data.

Experimental measurements of a 1:20-scale tractor-trailer configuration were obtained in the 48- by 32-Inch Subsonic Wind Tunnel at NASA Ames Research Center. The model included significant details of the underbody geometries of both the tractor and trailer. In addition, the tractor included a flow-through grill and a simplified engine block to provide an approximation of the flow through the engine compartment. The experiment was conducted at a Reynolds Number of 430,000 for yaw angles between ±14 deg. The measurements included forces and moments and static surface pressures for various underbody configurations. Simple fairings on the underbodies of the tractor and trailer both yielded a reduction in the wind-averaged drag coefficient of 0.018 (2.7%) when tested separately. A horizontal plate designed to block vertical flow in the tractor-trailer gap provided marginally higher drag reduction (0.021, or 3.2%).

Hover and ground-effect tests were conducted with the Lockheed-Martin Large Scale Powered Model (LSPM) during June-November 1995 at the Outdoor Aerodynamics Research Facility (OARF) located at NASA Ames Research Center. This was done in support of the Joint Strike Fighter (JSF) Program being lead by the Department of Defense. The program was previously referred to as the Joint Advanced Strike Technology (JAST) Program. The tests at the OARF included: engine thrust calibrations out of ground effect, measurements of individual nozzle jet pressure decay characteristics, and jet-induced hover force and moment measurements in and out of ground effect. The engine calibrations provide data correlating propulsion system throttle and nozzle settings with thrust forces and moments for the bare fuselage with the wings, canards, and tails removed. This permits measurement of propulsive forces and moments while minimizing any of the effects due to the presence of the large horizontal surfaces.

The NASA Specialized Center of Research and Training in Advanced Life Support (ALS/NSCORT) Education and Outreach Program is designed to engage audiences through concepts and technologies highlighted in the NSCORT research program. The outreach program is composed of three thrust areas. These areas are technical outreach (graduate education, technology transfer, presentations to industry, etc.), educational outreach (professional development, undergraduate, K-12), and public outreach (museums, state fairs, etc.) Program design of the technical and educational outreach began in January 2003. This paper reports anecdotal data on one ALS/NSCORT outreach program and gives a brief description of the other programs in their pilot stages. Technical and educational outreach programs developed to date include: 1) Summer Fellowship Research Program, 2) Distance Learning Course, 3) Key Learning Community Collaborative Project and 4) Mission to Mars.

Rolling element bearings provide near frictionless relative motion between two rotating parts. Automotive transmissions use various ball and rolling element bearings to accommodate the relative motion between rotating elements. In order to understand changes in bearing performance due to the loads imposed through the transmission, advanced modeling of the bearing is required. This paper focuses on the effects of cage flexibility on bearing performance. A flexible cage model was developed and incorporated into a six degree-of-freedom dynamic, deep groove ball bearing model. A lumped mass approach was used to represent the cage flexibility and was validated through an ANSYS forced response analyses of the cage. Results from the newly developed Flexible Cage Model (FCM) and an identical numerical model employing a rigid bearing cage were compared to determine the effects of varying ball-to-cage pocket clearance and cage stiffness on cage motion and ball-to-cage pocket contact forces.

Conventional suspension analysis of three-dimensional suspensions typically use two-dimensional analyses. This is done by projecting suspension components onto two-dimensional planes and then performing a two-dimensional analysis in each of these orthogonal planes or neglecting motions in one of the planes entirely. This requires multiple iterations because changes in one plane require a checking of their effects on motion in the other orthogonal planes. In doing so, much of the insight and accuracy gained from a three-dimensional analysis can be lost. A three-dimensional kinematic analysis approach is presented and applied to a dual A-Arm suspension system. All motions are considered instantaneously about a screw axis instead of a point as used by the usual two-dimensional modeling approach. The model predicts deflections of suspension components in response to the three-dimensional forces present at the contact patch.

Typical vehicle dynamics simulations demand a trade-off between short computation times and accuracy. Many of the more simple models are based on the kinematic roll center and the more accurate models tend to be multi-body dynamics simulation programs. There is a need for a model that improves the accuracy of the kinematic roll center models while still maintaining short computation times. Such a model could be used track-side during races to guide race teams toward improved handling. The model presented in this paper removes many of the assumptions and limitations of the kinematic roll center model. The model accounts for three-dimensional forces present at the contact patch and predicts deflections of suspension components. The modeling approach is applied to a NASCAR Craftsman Truck to predict the effects of suspension design and tuning on steady-state understeer characteristics of the vehicle. Braking and acceleration forces can also be applied to the vehicle.

Propulsion system sizing for mechanical flap and externally blown flap aircraft is demonstrated. Included in this study is the effect of various levels of noise suppression on the aircraft final design characteristics. Both aircraft are sized to operate from a 3000 ft runway and perform the same mission. For each aircraft concept, propulsion system sizing is demonstrated for two different engine cycles-one having a fan pressure ratio of 1.5 and a bypass ratio of 9 and the other having a fan pressure ratio of 1.25 and a bypass ratio of 17.8. The results presented include the required thrust to weight ratio, wing loading, resulting gross weight and direct operating costs as functions of the engine noise level for each combination of engine cycle and aircraft concept.

The short takeoff and landing capabilities that characterize the performance of powered-lift aircraft are dependent on engine thrust and are, therefore, severely affected by loss of an engine. This paper shows that the effects of engine loss on the short takeoff and landing performance of powered-lift aircraft can be effectively mitigated by cross-shafting the engine fans in a twin-engine configuration. Engine-out takeoff and landing performances are compared for three powered-lift aircraft configurations: one with four engines, one with two engines, and one with two engines in which the fans are cross-shafted. The results show that the engine-out takeoff and landing performance of the cross-shafted two-engine configuration is significantly better than that of the two-engine configuration without cross-shafting.

This paper summarizes the recent development of an adaptive aeroelastic wing shaping control technology called variable camber continuous trailing edge flap (VCCTEF). As wing flexibility increases, aeroelastic interactions with aerodynamic forces and moments become an increasingly important consideration in aircraft design and aerodynamic performance. Furthermore, aeroelastic interactions with flight dynamics can result in issues with vehicle stability and control. The initial VCCTEF concept was developed in 2010 by NASA under a NASA Innovation Fund study entitled “Elastically Shaped Future Air Vehicle Concept,” which showed that highly flexible wing aerodynamic surfaces can be elastically shaped in-flight by active control of wing twist and bending deflection in order to optimize the spanwise lift distribution for drag reduction. A collaboration between NASA and Boeing Research & Technology was subsequently funded by NASA from 2012 to 2014 to further develop the VCCTEF concept.

Lower cervical spine injuries are more common in survivors of motor vehicle crashes sustaining neck trauma. Injury criteria are determined using upper neck loads in dummies although a lower neck load cell exists. Due to a paucity of lower neck data from post mortem human subject (PMHS) studies, this research was designed to determine the head-neck biomechanics with a focus on lower neck metrics and injuries. Sixteen frontal impact tests were conducted using five belted PMHS. Instrumentation consisted of a pyramid-shaped nine accelerometer package on the head, tri-axial accelerometer on T1, and uniaxial accelerometer on the sled. Three-dimensional kinematics of the head-neck complex were obtained using a 20-camera high-speed motion analysis system. Testing sequence was: low (3.6 m/s), medium (6.9 m/s), repeat low, and high (15.8 m/s) velocities. Trauma evaluations were made between tests. Testing was terminated upon confirmation of injuries.